HBL4K

DC COMPONENTS CO., LTD. R HBL4A THRU HBL4M RECTIFIER SPECIALISTS TECHNICAL SPECIFICATIONS OF SINGLE-PHASE SILICON BRIDGE RECTIFIER VOLTAGE RANGE - 50 to 1000 Volts CURRENT - 4.0 Amperes FEATURES * Ideal for printed circuit board * Surge overload rating: 120 Amperes peak HBL MECHANICAL DATA * * * * * Case: Molded plastic Epoxy: UL 94V-0 rate flame retardant Terminals: MIL-STD-202E, Method 208 guaranteed Polarity: Symbols molded or marked on body Mounting position: Any .125(3.2) o 45 Chamfer .81(20.6) .77(19.6) .187(4.7) .148(3.8) .44(11.2) .42(10.7) AC .095(2.4) .065(1.6) .68(17.3) .62(15.7) .080(2.0) .065(1.7) .045(1.1) .035(0.9) .060(1.5) .045(1.1) .020(0.5) .015(0.4) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. .209(5.3) SPACING .189(4.8) Dimensions in inches and (millimeters) SYMBOL Maximum Recurrent Peak Reverse Voltage Maximum RMS Bridge Input Voltage Maximum DC Blocking Voltage Maximum Average Forward Output Current at TA = 5 0 C Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum Forward Voltage Drop per element at 3.0A DC Maximum DC Reverse Current at Rated DC Blocking Voltage per element I t Rating for Fusing (t*8.3ms) Typical Junction Capacitance ( Note1) Typical Thermal Resistance (Note 2) Operating Temperature Range Storage Temperature Range NOTES : 1. Measured at 1 MHZ and applied reverse voltage of 4.0 volts 2 o HBL4A 50 35 50 HBL4B 100 70 100 HBL4D 200 140 200 HBL4G 400 280 400 4.0 120 1.0 10 500 HBL4J 600 420 600 HBL4K 800 560 800 HBL4M 1000 700 1000 UNITS Volts Volts Volts Amps Amps Volts µAmps A 2 Sec pF 0 VRRM VRMS VDC IO I FSM VF IR It CJ RθJ A TJ TSTG 2 @T A = 25 oC @T A = 100 oC 93 40 19 -55 to +150 -55 to +150 C/W 0 0 C C 2.Thermal Resistance from Junction to Case per element Unit mounted on 300x300x1.6mm Aluminum plate heat-sink. RATING AND CHARACTERISTIC CURVES (HBL4A THRU HBL4M) FIG. 1 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, (A) 300 250 200 150 100 50 0 FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE AVERAGE FORWARD OUTPUT CURRENT, (A) 5 8.3ms Single Half Sine-Wave (JEDEC Mathod) 4 3 2 Single Phase Half Wave 60Hz Inductive or Resistive Load 1 1 2 5 10 20 50 100 0 50 100 150 NUMBER OF CYCLES AT 60Hz CASE TEMPERATURE, (oC) FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, (µA) INSTANTANEOUS FORWARD CURRENT, (A) 100 10 FIG. 4 - TYPICAL REVERSE CHARACTERISTICS TJ=25oC TJ=100oC 10 1.0 Pulse Width=300ms 1% Duty Cycle 1 .1 TJ=25oC .1 .6 .8 1.0 1.2 1.4 1.6 1.8 2.0 .01 0 20 40 60 80 100 120 140 INSTANTANEOUS FORWARD VOLTAGE, (V) PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) DC COMPONENTS CO., LTD. R