521-9632

2mm LED CBI® Circuit Board Indicator (DIN 41494 Compatible), Bi-Level HOUSING TYPE 0 WITHOUT PINS 2.50 [.095] 1.52 ±.20 [.060 ±.008] 13.72 [.540] 1.37 [.054] HOUSING TYPE 1 WITH PINS 1.27 [.050] MAX 5.08 [.20..0] 5.08 [.200] 571-01xx 2.54 ±.05 [.100 ±.002] TYP (3) 8.60 [.339] 3.81 [.150] 2.54 [.100] 1.80 ±.20 [.071 ±.008] 0.38 [.015] 3.00 ±.25 [.118 ±.010] 3.81 [.150] 2.54 [.100] CATHODE 0.46 [.018] 4.83 [.190] Ø 1.02 ±.05 [.040 ±.002] TYP (4) RECOMMENDED PC BOARD HOLE PATTERN 0.38 [.015] 0.41 [.016] 2.54 [.100] 2.54 [.100] CATHODE TOP LED 2.54 [.100] Except where noted Housing Type 1 dimensions are the same as Housing Type 0 Dimensions in mm [inches] Features • Designed to accommodate DIN 41494 • Multiple CBIs form horizontal LED arrays on 2.54mm • • • • (0.100”) center-lines High Contrast, UL 94 V-0 rated, black housing Oxygen index: 32% Polymer content: PBT, 0.290 g Housing stand-offs facilitate PCB cleaning PART NO. WITHOUT PINS 571-0111 571-0112 571-0122 571-0132 571-0133 * Top-Bottom LED PART NO. WITH PINS 571-0111-100 571-0112-100 571-0122-100 571-0132-100 571-0133-100 * Top-Bottom LED COLOR* Red-Red Red-Green Green-Green Yellow-Green Yellow-Yellow COLOR* Red-Red Red-Green Green-Green Yellow-Green Yellow-Yellow • Solderability per MIL-STD-202F, method 208F • LEDs are safe for direct viewing per IEC 825-1, EN-60825-1 Tolerance note: As noted, otherwise: • LED Protrusion: ±0.04 mm [±0.016] • CBI Housing: ±0.02mm[±0.008] PART NUMBER ORDERING CODE Series Top LED Color Array Code Arrays available. See Part Number ordering code. Custom Combinations • Contact factory for information on custom color combinations. EXAMPLE Single unit with pins 571– 01xx –10x LED Type Bottom LED Color 1) With pins Number of Bi-Levels in array LED colors: 0) Blank, 1) Red, 2) Green, 3) Yellow –10x Suffix required only when ordering single units with pins or arrays 571– 01xx –100 102 Two bi-levels in an array (4 LEDs) Typical Operating Characteristics (TA = 25°C) GENERAL PURPOSE Part Number 571-01xx * IF = 10mA See LED data sheet for additional information See Page 3-17 and 3-18 for Reference Only LED Drive Circuit Examples See Page 3-20 for Pin Out Color Red Green Yellow ** IF = 20mA Peak Wavelength nm 635 565 585 IV* mcd 12.6 8.7 12.6 V F ** Volts 2 2.1 2.1 Viewing Angle 2 Θ1/2 38° 38° 38° LED Data sheet 521-9630 521-9632 521-9631 Page # 3-13 3-13 3-13 3-10 Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com 2mm Discrete LED Diffused 521-9630, -9631, -9632 CATHODE I.D. 2.40 [.095] 2.90 [.114] 25.40 [1.00] MIN CATHODE 3.30 [.13] 1.80 [.071] .45 [.018] TYP .40 [.016] TYP 1.00 [.04] MIN 2.54 [.10] NOM PART NO. 521-9630 521-9631 521-9632 COLOR Red Yellow Green R 1.65 [.065] 1.52 [.060] 3.30 [.130] 1.50 [.059] MAX Dimensions in mm [inches] 3 Red Yellow Green ABSOLUTE MAXIMUM RATINGS (TA=25°C) Power Dissipation (mW) Forward Current (mA) Derating (mA/°C) From 25°C Peak Current (mA) Pulse width = 10µs -9630 100 30 .4 120 -55/+100 -55/+100 -9631 60 20 .25 80 -55/+100 -55/+100 -9632 100 30 .4 120 -55/+100 -55/+100 Operating Temperature (°C) Storage Temperature (°C) Soldering Temperature 260°C, 5 seconds, 1.6 mm from case Red Yellow Green OPERATING CHARACTERISTICS (TA=25°C) Luminous Intensity (mcd) IF=10mA Peak Wavelength (nm) λ Peak Viewing Angle (2 Θ1/2) Forward Voltage (V) IF=20mA Reverse Voltage (V), IR=100µA Min. Typical Typical Typical Typical Max. Min. -9630 3.7 12.6 635 38° 2 2.8 5 -9631 3.7 12.6 585 38° 2.1 2.8 5 -9632 2.5 8.7 565 38° 2.1 2.8 5 Θ 1¼2is the off axis angle at which the luminous intensity is half the axial luminous intensity Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com 3-13