ES51F2E30V-20000M

Marketing Bulletin DATE: TO: FROM: RE: May 10, 2004 Affected Customers Mark Stoner Product Termination To all concerned parties, This bulletin is to notify all customers of the termination of the following Ecliptek series effective May 10th, 2004: Series EB51F2 ES51F2 EB52F2 ES52F2 Description 5V 14 Pin DIP TCXO, HCMOS 5V 14 Pin DIP TCXO, Sinewave 3.3V 14 Pin DIP TCXO, HCMOS 3.3V 14 Pin DIP TCXO, Sinewave Recommended Replacement None None None None Because of the circumstances surrounding this termination, there will be no end-of-life policy exercised. The series will be terminated with no purchasing or lifetime buy window available. We will however have a recommended alternative product for these series within the next ninety (90) days. All of us at Ecliptek Corporation apologize for any inconvenience this may have caused and can assure you we are taking measures to insure this will not happen again in the future. If there are any questions pertaining to this bulletin, please feel free to contact me. Thank you for your cooperation. Best Regards, Mark W. Stoner Director of Marketing Ecliptek Corporation 3545 CADILLAC AVENUE • COSTA MESA, CA 92626-1401 • (714) 433-1200 • Fax (714) 433-1234 STANDARD SPECIFICATIONS Frequency Range: Frequency Tolerance/Stability: Initial Frequency Tolerance vs. Operating Temperature Range vs. Input Voltage Change vs. Load Change vs. Aging Operating Temperature Range Storage Temperature Range Supply Voltage (VDD ) Input Current (Steady State @25°C) Output Voltage Logic High Output Voltage Logic Low Rise/Fall Time Duty Cycle Load Drive Capabillity Phase Noise (Typical) Frequency Deviation Control VoltageRange(VCR ) Control Voltage /TransferFunction Linearity Input Impedance Fine Leak Test: Gross Leak Test: Mechanical Shock: Vibration: Lead Integrity: 1.544MHz to 44.736MHz ±1ppm (at Nominal Vdd and Vc) See Table 1 for Maximum Values ±0.3ppm Maximum (VDD ±5%) ±0.2ppm Maximum (±10%) ±1ppm/year Maximum (@25°C) See Table 1 for Operating Temperature Range -55°C to +125°C 5.0Vdc ±5% 15mA Maximum < 20.000MHz 30mA Maximum > 20.000MHz VDD-0.5Vdc Minimum 0.5Vdc Maximum 6nSec (20% to 80% of waveform) 50% ±5% (@ 50% of waveform) 30pF HCMOS Load -60dBc/Hz at 10Hz Offset, -90dBc/Hz at 100Hz Offset, -125dBc/Hz at 1kHz Offset, -135dBc/Hz at 10kHz Offset, -140dBc/Hz at 100kHz Offset, ±7ppm Minimum, ±20ppm Maximum (Referenced to Fo at Vc=2.5Vdc; Vdd=5.0Vdc) 0.0VDC to VDD 2.5VDC ±2.0VDC / Positive Transfer Characteristic ±10% Maximum 10kOhms Typical OBSOLETE ENVIRONMENTAL & MECHANICAL MIL-STD-883, Method MIL-STD-883, Method MIL-STD-202, Method MIL-STD-883, Method MIL-STD-883, Method 1014, Condition A 1014, Condition C 213, Condition C 2007, Condition A 2004 Solderability: Temperature Cycling: Resistance to Soldering Heat: Resistance to Solvents: MIL-STD-883, Method 2002 MIL-STD-883, Method 1010 MIL-STD-202, Method 210 MIL-STD-202, Method 215 TABLE 1: PART NUMBERING CODES FREQUENCY STABILITY X Denotes availability from 1.544MHz to 32.768MHz Y Denotes availability for any valid frequency Range Code 50 30 20 15 Code ±1.5ppm ±2.0ppm ±3.0ppm ±5.0ppm Range 0°C to +50°C Y Y Y Y A 0°C to +70°C Y Y Y X B Y Y X X -20°C to +70°C C Y Y X -30°C to +75°C D Y X -40°C to +85°C E OPERATING TEMPERATURE PART NUMBERING GUIDE EB51F2 A 10 V - 20.000M Frequency Voltage Control Option V = Voltage Control on Pin 1 N = No Connect on Pin 1 Frequency Stability Code Per Table 1 Operating Temperature Range Code Per Table 1 MARKING GUIDE (Line #1) ECLIPTEK (Line #2) XX.XXXM ECLIPTEK XX.XXXM XXYZZ 1 15.240 ±0.203 Frequency 7 0.6 MAX (Line #3) XX Y ZZ 7.620 ±0.203 ∅0.457 ±0.100 (X4) 8 Week of Year Last Digit of Year Ecliptek Manufacturing Code (TEN02-001-000) NOTE: Pin 1 shall be marked with a dot. Marking shall conform to conditions listed in TQC41-001-000. 8.3 MAX 14 20.3 ±0.5 5.08 MIN 13.0 ±0.5 SPECIFICATION CONTROL DRAWING Drawing Number CSC26-140-001 Title ALL DIMENSIONS IN MILLIMETERS 5.0V Full Size (VC)TCXO Revision Effectivity Date PIN CONNECTION 1 No Connect or Voltage Control 7 Ground/Case Ground 8 Output 14 Supply Voltage A ECN Number 09-09-03 PAGE 1 OF 2 Date Released By Date 8159 Approved By STANDARD SPECIFICATIONS Frequency Range: Frequency Tolerance/Stability: Initial Frequency Tolerance vs. Operating Temperature Range vs. Input Voltage Change vs. Load Change vs. Aging Operating Temperature Range Storage Temperature Range Supply Voltage (VDD ) Input Current (Steady State @25°C) Output Voltage Load Drive Capabillity Phase Noise (Typical) Frequency Deviation Control VoltageRange(VCR ) Control Voltage /TransferFunction Linearity Input Impedance Fine Leak Test: Gross Leak Test: Mechanical Shock: Vibration: Lead Integrity: 9.600MHz to 44.736MHz ±1ppm (at Nominal Vdd and Vc) See Table 1 for Maximum Values ±0.3ppm Maximum (VDD ±5%) ±0.2ppm Maximum (±10%) ±1ppm/year Maximum (@25°C) See Table 1 for Operating Temperature Range -55°C to +125°C 5.0Vdc ±5% 10mA Maximum 1.0Vp-p Minimum Clipped Sinewave 10kOhms//10pF -60dBc/Hz at 10Hz Offset, -90dBc/Hz at 100Hz Offset, -125dBc/Hz at 1kHz Offset, -135dBc/Hz at 10kHz Offset, -140dBc/Hz at 100kHz Offset ±7ppm Minimum, ±20ppm Maximum (Referenced to Fo at Vc=2.5Vdc; Vdd=5.0Vdc) 0.0VDC to VDD 2.5VDC ±2.0VDC / Positive Transfer Characteristic ±10% Maximum 10kOhms Typical OBSOLETE ENVIRONMENTAL & MECHANICAL MIL-STD-883, Method MIL-STD-883, Method MIL-STD-202, Method MIL-STD-883, Method MIL-STD-883, Method 1014, Condition A 1014, Condition C 213, Condition C 2007, Condition A 2004 Solderability: Temperature Cycling: Resistance to Soldering Heat: Resistance to Solvents: MIL-STD-883, Method 2002 MIL-STD-883, Method 1010 MIL-STD-202, Method 210 MIL-STD-202, Method 215 TABLE 1: PART NUMBERING CODES FREQUENCY STABILITY X Denotes availability from 9.600MHz to 32.768MHz Y Denotes availability for any valid frequency Range Code 50 30 20 15 Code ±1.5ppm ±2.0ppm ±3.0ppm ±5.0ppm Range 0°C to +50°C Y Y Y Y A 0°C to +70°C Y Y Y X B -20°C to +70°C Y Y X C Y Y D -30°C to +75°C Y X -40°C to +85°C E OPERATING TEMPERATURE PART NUMBERING GUIDE ES51F2 A 10 V - 20.000M Frequency Voltage Control Option V = Voltage Control on Pin 1 N = No Connect on Pin 1 Frequency Stability Code Per Table 1 Operating Temperature Range Code Per Table 1 MARKING GUIDE (Line #1) ECLIPTEK (Line #2) XX.XXXM Frequency (Line #3) XX Y ZZ 1 ECLIPTEK XX.XXXM XXYZZ 15.240 ±0.203 7 0.6 MAX Week of Year Last Digit of Year Ecliptek Manufacturing Code (TEN02-001-000) NOTE: Pin 1 shall be marked with a dot. Marking shall conform to conditions listed in TQC41-001-000. 7.620 ±0.203 ∅0.457 ±0.100 (X4) 8 14 20.3 ±0.5 5.08 MIN 13.0 ±0.5 8.3 MAX SPECIFICATION CONTROL DRAWING Drawing Number CSC26-160-001 Title ALL DIMENSIONS IN MILLIMETERS 5.0V Clipped Sinewave Full Size (VC)TCXO Revision Effectivity Date PIN CONNECTION 1 No Connect or Voltage Control 7 Ground/Case Ground 8 Output 14 Supply Voltage A ECN Number 09-09-03 PAGE 1 OF 2 Date Released By Date 8163 Approved By STANDARD SPECIFICATIONS Frequency Range: Frequency Tolerance/Stability: Initial Frequency Tolerance vs. Operating Temperature Range vs. Input Voltage Change vs. Load Change vs. Aging Operating Temperature Range Storage Temperature Range Supply Voltage (VDD ) Input Current (Steady State @25°C) Output Voltage Logic High Output Voltage Logic Low Rise/Fall Time Duty Cycle Load Drive Capabillity Phase Noise (Typical) Frequency Deviation Control VoltageRange(VCR ) Control Voltage /TransferFunction Linearity Input Impedance Fine Leak Test: Gross Leak Test: Mechanical Shock: Vibration: Lead Integrity: 1.544MHz to 44.736MHz ±1ppm (at Nominal Vdd and Vc) See Table 1 for Maximum Values ±0.3ppm Maximum (VDD ±5%) ±0.2ppm Maximum (±10%) ±1ppm/year Maximum (@25°C) See Table 1 for Operating Temperature Range -55°C to +125°C 3.3Vdc ±5% 15mA Maximum < 20.000MHz 25mA Maximum > 20.000MHz 90% of Vdd Minimum 10% of Vdd Maximum 6nSec (20% to 80% of waveform) 50% ±5% (@ 50% of waveform) 15pF HCMOS Load -60dBc/Hz at 10Hz Offset, -90dBc/Hz at 100Hz Offset, -125dBc/Hz at 1kHz Offset, -135dBc/Hz at 10kHz Offset, -140dBc/Hz at 100kHz Offset, ±7ppm Minimum, ±20ppm Maximum (Referenced to Fo at Vc=1.65Vdc; Vdd=3.3Vdc) 0.0VDC to VDD 1.65VDC ±1.35VDC / Positive Transfer Characteristic ±10% Maximum 10kOhms Typical OBSOLETE ENVIRONMENTAL & MECHANICAL MIL-STD-883, Method MIL-STD-883, Method MIL-STD-202, Method MIL-STD-883, Method MIL-STD-883, Method 1014, Condition A 1014, Condition C 213, Condition C 2007, Condition A 2004 Solderability: Temperature Cycling: Resistance to Soldering Heat: Resistance to Solvents: MIL-STD-883, Method 2002 MIL-STD-883, Method 1010 MIL-STD-202, Method 210 MIL-STD-202, Method 215 TABLE 1: PART NUMBERING CODES FREQUENCY STABILITY X Denotes availability from 1.544MHz to 32.768MHz Y Denotes availability for any valid frequency Range Code 50 30 20 15 Code ±1.5ppm ±2.0ppm ±3.0ppm ±5.0ppm Range 0°C to +50°C Y Y Y Y A 0°C to +70°C Y Y Y X B Y Y X -20°C to +70°C C Y Y -30°C to +75°C D Y X -40°C to +85°C E OPERATING TEMPERATURE PART NUMBERING GUIDE EB52F2 A 10 V - 20.000M Frequency Voltage Control Option V = Voltage Control on Pin 1 N = No Connect on Pin 1 Frequency Stability Code Per Table 1 Operating Temperature Range Code Per Table 1 MARKING GUIDE (Line #1) ECLIPTEK (Line #2) XX.XXXM ECLIPTEK XX.XXXM XXYZZ 1 15.240 ±0.203 Frequency 7 0.6 MAX (Line #3) XX Y ZZ 7.620 ±0.203 ∅0.457 ±0.100 (X4) 8 Week of Year Last Digit of Year Ecliptek Manufacturing Code (TEN02-001-000) NOTE: Pin 1 shall be marked with a dot. Marking shall conform to conditions listed in TQC41-001-000. 8.3 MAX 14 20.3 ±0.5 5.08 MIN 13.0 ±0.5 SPECIFICATION CONTROL DRAWING Drawing Number CSC26-150-001 Title ALL DIMENSIONS IN MILLIMETERS 3.3V FULL SIZE (VC)TCXO Revision Effectivity Date PIN CONNECTION 1 No Connect or Voltage Control 7 Ground/Case Ground 8 Output 14 Supply Voltage A ECN Number 09-09-03 PAGE 1 OF 2 Date Released By Date 8161 Approved By STANDARD SPECIFICATIONS Frequency Range: Frequency Tolerance/Stability: Initial Frequency Tolerance vs. Operating Temperature Range vs. Input Voltage Change vs. Load Change vs. Aging Operating Temperature Range Storage Temperature Range Supply Voltage (VDD ) Input Current (Steady State @25°C) Output Voltage Load Drive Capabillity Phase Noise (Typical) Frequency Deviation Control VoltageRange(VCR ) Control Voltage /TransferFunction Linearity Input Impedance Fine Leak Test: Gross Leak Test: Mechanical Shock: Vibration: Lead Integrity: 9.600MHz to 44.736MHz ±1ppm (at Nominal Vdd and Vc) See Table 1 for Maximum Values ±0.3ppm Maximum (VDD ±5%) ±0.2ppm Maximum (±10%) ±1ppm/year Maximum (@25°C) See Table 1 for Operating Temperature Range -55°C to +125°C 3.3Vdc ±5% 10mA Maximum 0.7Vp-p Minimum Clipped Sinewave 10kOhms//10pF -60dBc/Hz at 10Hz Offset, -90dBc/Hz at 100Hz Offset, -125dBc/Hz at 1kHz Offset, -135dBc/Hz at 10kHz Offset, -140dBc/Hz at 100kHz Offset ±7ppm Minimum, ±20ppm Maximum (Referenced to Fo at Vc=1.65Vdc; Vdd=3.3Vdc) 0.0VDC to VDD 1.65VDC ±1.35VDC / Positive Transfer Characteristic ±10% Maximum 10kOhms Typical OBSOLETE ENVIRONMENTAL & MECHANICAL MIL-STD-883, Method MIL-STD-883, Method MIL-STD-202, Method MIL-STD-883, Method MIL-STD-883, Method 1014, Condition A 1014, Condition C 213, Condition C 2007, Condition A 2004 Solderability: Temperature Cycling: Resistance to Soldering Heat: Resistance to Solvents: MIL-STD-883, Method 2002 MIL-STD-883, Method 1010 MIL-STD-202, Method 210 MIL-STD-202, Method 215 TABLE 1: PART NUMBERING CODES FREQUENCY STABILITY X Denotes availability from 9.600MHz to 32.768MHz Y Denotes availability for any valid frequency Range Code 50 30 20 15 Code ±1.5ppm ±2.0ppm ±3.0ppm ±5.0ppm Range 0°C to +50°C Y Y Y Y A 0°C to +70°C Y Y Y X B -20°C to +70°C Y Y X C Y Y D -30°C to +75°C Y X -40°C to +85°C E OPERATING TEMPERATURE PART NUMBERING GUIDE ES52F2 A 10 V - 20.000M Frequency Voltage Control Option V = Voltage Control on Pin 1 N = No Connect on Pin 1 Frequency Stability Code Per Table 1 Operating Temperature Range Code Per Table 1 MARKING GUIDE (Line #1) ECLIPTEK (Line #2) XX.XXXM Frequency (Line #3) XX Y ZZ 1 ECLIPTEK XX.XXXM XXYZZ 15.240 ±0.203 7 0.6 MAX Week of Year Last Digit of Year Ecliptek Manufacturing Code (TEN02-001-000) NOTE: Pin 1 shall be marked with a dot. Marking shall conform to conditions listed in TQC41-001-000. 7.620 ±0.203 ∅0.457 ±0.100 (X4) 8 14 20.3 ±0.5 5.08 MIN 13.0 ±0.5 8.3 MAX SPECIFICATION CONTROL DRAWING Drawing Number CSC26-170-001 Title ALL DIMENSIONS IN MILLIMETERS 3.3V Clipped Sinewave Full Size (VC)TCXO Revision Effectivity Date PIN CONNECTION 1 No Connect or Voltage Control 7 Ground/Case Ground 8 Output 14 Supply Voltage A ECN Number 09-09-03 PAGE 1 OF 2 Date Released By Date 8165 Approved By