B32672L8103J189

Film Capacitors Metallized Polypropylene Film Capacitors (MKP) Series/Type: B32671L, B32672L Date: August 2019 © TDK Electronics AG 2020. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without TDK Electronics' prior express consent is prohibited. Metallized polypropylene film capacitors (MKP) B32671L, B32672L High V AC, high temperature (wound) Typical applications Electronic ballasts (resonant circuits) SMPS High-frequency AC loads Pulse circuits Dimensional drawing Climatic Max. operating temperature: 125 °C Climatic category (IEC 60068-1:2013): 55/110/56 Construction Dielectric: metallized polypropylene (PP) Wound capacitor technology Plastic case (UL 94 V-0) Epoxy resin sealing Dimensions in mm Features Very high AC voltages for all frequency ranges Very small dimensions High peak voltage for short time periods High peak current High pulse withstand capability RoHS-compatible Halogen-free capacitors available on request AEC-Q200D compliant Lead spacing ±0.4 10 15 Terminals Parallel wire leads, lead-free tinned Special lead lengths available on request Marking Manufacturer's logo lot number, series number Rated capacitance (coded) Capacitance tolerance (code letter) Rated voltage Date of manufacture (coded) Delivery mode Bulk (untaped) Taped (Ammo pack or reel) For notes on taping, refer to chapter "Taping and packing“. Please read Cautions and warnings and Important notes at the end of this document. Page 2 of 39 Lead diameter Type d1 ±0.05 0.6 B32671L 0.8 B32672L B32671L, B32672L High V AC, high temperature (wound) Overview of available types Lead spacing 10 mm 15 mm Type B32671L B32672L Page 4 6 VRMS (V AC) 200 250 250 500 600 700 160 200 250 250 500 600 700 900 VR (V DC) 400 630 1000 1000 1600 2000 250 450 630 1000 1300 1600 2000 2000 CR (nF) 1.0 1.2 1.5 2.2 2.7 3.3 3.9 4.7 5.6 6.2 6.8 8.2 10 12 15 22 33 47 56 68 100 150 220 330 390 470 680 1000 Please read Cautions and warnings and Important notes at the end of this document. Page 3 of 39 B32671L High V AC, high temperature (wound) Ordering codes and packing units (lead spacing 10 mm) VRMS VR CR f ≤1 kHz V AC V DC nF 200 400 22 33 47 68 100 250 630 15 22 33 47 56 250 1000 4.7 6.8 10 15 22 500 1000 3.3 3.9 4.7 5.6 6.2 6.8 8.2 10 12 Max. dimensions w×h×l mm 4.0 × 9.0 × 13.0 4.0 × 9.0 × 13.0 5.0 × 11.0 × 13.0 5.0 × 11.0 × 13.0 6.0 × 12.0 × 13.0 4.0 × 9.0 × 13.0 5.0 × 11.0 × 13.0 5.0 × 11.0 × 13.0 6.0 × 12.0 × 13.0 6.0 × 12.0 × 13.0 4.0 × 9.0 × 13.0 4.0 × 9.0 × 13.0 5.0 × 11.0 × 13.0 5.0 × 11.0 × 13.0 6.0 × 12.0 × 13.0 4.0 × 9.0 × 13.0 4.0 × 9.0 × 13.0 4.0 × 9.0 × 13.0 5.0 × 11.0 × 13.0 5.0 × 11.0 × 13.0 5.0 × 11.0 × 13.0 6.0 × 12.0 × 13.0 6.0 × 12.0 × 13.0 6.0 × 12.0 × 13.0 Ordering code (composition see below) B32671L4223+*** B32671L4333+*** B32671L4473+*** B32671L4683+*** B32671L4104+*** B32671L6153+*** B32671L6223+*** B32671L6333+*** B32671L6473+*** B32671L6563+*** B32671L9472+*** B32671L9682+*** B32671L9103+*** B32671L9153+*** B32671L9223+*** B32671L0332+*** B32671L0392+*** B32671L0472+*** B32671L0562+*** B32671L0622+*** B32671L0682+*** B32671L0822+*** B32671L0103+*** B32671L0123+*** Ammo pack pcs./MOQ 4000 4000 3320 3320 2720 4000 3320 3320 2720 2720 4000 4000 3320 3320 2720 4000 4000 4000 3320 3320 3320 2720 2720 2720 Reel Untaped pcs./MOQ 6800 6800 5200 5200 4400 6800 5200 5200 4400 4400 6800 6800 5200 5200 4400 6800 6800 6800 5200 5200 5200 4400 4400 4400 pcs./MOQ 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series, intermediate capacitance values and closer tolerances on request. Composition of ordering code + = Capacitance tolerance code: K = ±10% J = ±5% Please read Cautions and warnings and Important notes at the end of this document. *** = Packaging code: 289 = Straight terminals, Ammo pack 189 = Straight terminals, Reel 003 = Straight terminals, untaped (lead length 3.2 ± 0.3 mm) 000 = Straight terminals, untaped (lead length 61 mm) Page 4 of 39 B32671L High V AC, high temperature (wound) Ordering codes and packing units (lead spacing 10 mm) VRMS VR CR f ≤1 kHz V AC V DC nF 600 1600 1.2 1.5 2.2 2.7 3.3 3.9 4.7 700 2000 1.0 1.2 1.5 2.2 2.7 3.3 3.9 4.7 Max. dimensions w×h×l mm 4.0 × 9.0 × 13.0 4.0 × 9.0 × 13.0 5.0 × 11.0 × 13.0 5.0 × 11.0 × 13.0 6.0 × 12.0 × 13.0 6.0 × 12.0 × 13.0 6.0 × 12.0 × 13.0 4.0 × 9.0 × 13.0 4.0 × 9.0 × 13.0 4.0 × 9.0 × 13.0 5.0 × 11.0 × 13.0 5.0 × 11.0 × 13.0 5.0 × 11.0 × 13.0 6.0 × 12.0 × 13.0 6.0 × 12.0 × 13.0 Ordering code (composition see below) B32671L1122+*** B32671L1152+*** B32671L1222+*** B32671L1272+*** B32671L1332+*** B32671L1392+*** B32671L1472+*** B32671L8102+*** B32671L8122+*** B32671L8152+*** B32671L8222+*** B32671L8272+*** B32671L8332+*** B32671L8392+*** B32671L8472+*** Ammo pack pcs./MOQ 4000 4000 3320 3320 2720 2720 2720 4000 4000 4000 3320 3320 3320 2720 2720 Reel Untaped pcs./MOQ 6800 6800 5200 5200 4400 4400 4400 6800 6800 6800 5200 5200 5200 4400 4400 pcs./MOQ 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series, intermediate capacitance values and closer tolerances on request. Composition of ordering code + = Capacitance tolerance code: K = ±10% J = ±5% Please read Cautions and warnings and Important notes at the end of this document. *** = Packaging code: 289 = Straight terminals, Ammo pack 189 = Straight terminals, Reel 003 = Straight terminals, untaped (lead length 3.2 ± 0.3 mm) 000 = Straight terminals, untaped (lead length 61 mm) Page 5 of 39 B32672L High V AC, high temperature (wound) Ordering codes and packing units (lead spacing 15 mm) VRMS VR CR f ≤1 kHz V AC V DC nF 160 250 150 220 330 470 680 1000 200 450 68 100 150 220 330 470 680 250 630 33 47 68 100 150 220 390 Max. dimensions w×h×l mm 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 11.0 × 18.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 7.0 × 12.5 × 18.0 8.0 × 14.0 × 18.0 9.0 × 17.5 × 18.0 11.0 × 18.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 11.0 × 18.5 × 18.0 Ordering code (composition see below) B32672L2154+*** B32672L2224+*** B32672L2334+*** B32672L2474+*** B32672L2684+*** B32672L2105+*** B32672L4683+*** B32672L4104+*** B32672L4154+*** B32672L4224+*** B32672L4334+*** B32672L4474+*** B32672L4684+*** B32672L6333+*** B32672L6473+*** B32672L6683+*** B32672L6104+*** B32672L6154+*** B32672L6224+*** B32672L6394+*** Ammo pack pcs./MOQ 4680 3840 3320 2720 2560  4680 4680 3840 3320 2920 2560  4680 4680 3840 3320 2720 2560  Reel Untaped pcs./MOQ 5200 4400 3600 2800 2800 2200 5200 5200 4400 3600 3000 2800 2200 5200 5200 4400 3600 2800 2800 2200 pcs./MOQ 4000 4000 4000 2000 2000 1200 4000 4000 4000 4000 2000 2000 1200 4000 4000 4000 4000 2000 2000 1200 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series, intermediate capacitance values and closer tolerances on request. Composition of ordering code + = Capacitance tolerance code: K = ±10% J = ±5% Please read Cautions and warnings and Important notes at the end of this document. *** = Packaging code: 289 = Straight terminals, Ammo pack 189 = Straight terminals, Reel 003 = Straight terminals, untaped (lead length 3.2 ± 0.3 mm) 000 = Straight terminals, untaped (lead length 61 mm) Page 6 of 39 B32672L High V AC, high temperature (wound) Ordering codes and packing units (lead spacing 15 mm) VRMS VR CR f ≤1 kHz V AC V DC nF 250 1000 10 15 22 33 47 68 100 150 500 1300 6.8 10 22 33 47 68 600 1600 6.2 6.8 8.2 10 12 15 22 33 47 Max. dimensions w×h×l mm 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 11.0 × 18.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 11.0 × 18.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 6.0 × 11.0 × 18.0 6.0 × 12.0 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 11.0 × 18.5 × 18.0 Ordering code (composition see below) B32672L0103+*** B32672L0153+*** B32672L0223+*** B32672L0333+*** B32672L0473+*** B32672L0683+*** B32672L0104+*** B32672L0154+*** B32672L7682+*** B32672L7103+*** B32672L7223+*** B32672L7333+*** B32672L7473+*** B32672L7683+*** B32672L1622+*** B32672L1682+*** B32672L1822+*** B32672L1103+*** B32672L1123+*** B32672L1153+*** B32672L1223+*** B32672L1333+*** B32672L1473+*** Ammo pack pcs./MOQ 4680 4680 4680 3840 3320 2720 2560  4680 4680 3320 2720 2560  4680 4680 3840 3840 3840 3320 2720 2560  Reel Untaped pcs./MOQ 5200 5200 5200 4400 3600 2800 2800 2200 5200 5200 3600 2800 2800 2200 5200 5200 4400 4400 4400 3600 2800 2800 2200 pcs./MOQ 4000 4000 4000 4000 4000 2000 2000 1200 4000 4000 4000 2000 2000 1200 4000 4000 4000 4000 4000 4000 2000 2000 1200 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series, intermediate capacitance values and closer tolerances on request. Composition of ordering code + = Capacitance tolerance code: K = ±10% J = ±5% Please read Cautions and warnings and Important notes at the end of this document. *** = Packaging code: 289 = Straight terminals, Ammo pack 189 = Straight terminals, Reel 003 = Straight terminals, untaped (lead length 3.2 ± 0.3 mm) 000 = Straight terminals, untaped (lead length 61 mm) Page 7 of 39 B32672L High V AC, high temperature (wound) Ordering codes and packing units (lead spacing 15 mm) VRMS VR CR f ≤1 kHz V AC V DC nF 700 2000 1.0 1.2 1.5 2.2 2.7 3.3 3.9 4.7 5.6 6.2 6.8 8.2 10 12 15 22 33 Max. dimensions w×h×l mm 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 6.0 × 11.0 × 18.0 6.0 × 11.0 × 18.0 6.0 × 12.0 × 18.0 7.0 × 12.5 × 18.0 8.5 × 14.5 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 11.0 × 18.5 × 18.0 Ordering code (composition see below) B32672L8102+*** B32672L8122+*** B32672L8152+*** B32672L8222+*** B32672L8272+*** B32672L8332+*** B32672L8392+*** B32672L8472+*** B32672L8562+*** B32672L8622+*** B32672L8682+*** B32672L8822+*** B32672L8103+*** B32672L8123+*** B32672L8153+*** B32672L8223+*** B32672L8333+*** Ammo pack pcs./MOQ 4680 4680 4680 4680 4680 4680 4680 4680 3840 3840 3840 3840 3320 2720 2720 2560  Reel Untaped pcs./MOQ 5200 5200 5200 5200 5200 5200 5200 5200 4400 4400 4400 4400 3600 2800 2800 2800 2200 pcs./MOQ 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 2000 2000 2000 1200 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series, intermediate capacitance values and closer tolerances on request. Composition of ordering code + = Capacitance tolerance code: K = ±10% J = ±5% Please read Cautions and warnings and Important notes at the end of this document. *** = Packaging code: 289 = Straight terminals, Ammo pack 189 = Straight terminals, Reel 003 = Straight terminals, untaped (lead length 3.2 ± 0.3 mm) 000 = Straight terminals, untaped (lead length 61 mm) Page 8 of 39 B32672L High V AC, high temperature (wound) Ordering codes and packing units (lead spacing 15 mm) VRMS VR CR f ≤1 kHz V AC V DC nF 900 2000 1.0 1.2 1.5 2.2 2.7 3.3 3.9 4.7 5.6 6.2 6.8 Max. dimensions w×h×l mm 5.0 × 10.5 × 18.0 6.0 × 11.0 × 18.0 6.0 × 11.0 × 18.0 7.0 × 12.5 × 18.0 8.0 × 14.0 × 18.0 8.5 × 14.5 × 18.0 9.0 × 17.5 × 18.0 9.0 × 17.5 × 18.0 11.0 × 18.5 × 18.0 11.0 × 18.5 × 18.0 11.0 × 18.5 × 18.0 Ordering code (composition see below) B32672L9102+*** B32672L9122+*** B32672L9152+*** B32672L9222+*** B32672L9272+*** B32672L9332+*** B32672L9392+*** B32672L9472+*** B32672L9562+*** B32672L9622+*** B32672L9682K*** Ammo pack pcs./MOQ 4680 3840 3840 3320 2920 2720 2560 2560    Reel Untaped pcs./MOQ 5200 4400 4400 3600 3000 2800 2800 2800 2200 2200 2200 pcs./MOQ 4000 4000 4000 4000 2000 2000 2000 2000 1200 1200 1200 MOQ = Minimum Order Quantity, consisting of 4 packing units. Further E series, intermediate capacitance values and closer tolerances on request. Composition of ordering code + = Capacitance tolerance code: K = ±10% J = ±5% Please read Cautions and warnings and Important notes at the end of this document. *** = Packaging code: 289 = Straight terminals, Ammo pack 189 = Straight terminals, Reel 003 = Straight terminals, untaped (lead length 3.2 ± 0.3 mm) 000 = Straight terminals, untaped (lead length 61 mm) Page 9 of 39 B32671L, B32672L High V AC, high temperature (wound) Technical data Reference standard: IEC 60384-16:2005 and AEC-Q200D. All data given at T = 20 °C, unless otherwise specified. Rated temperature TR +85 °C Operating temperature range Max. operating temperature Top,max Upper category temperature Tmax Lower category temperature Tmin Rated temperature TR Dissipation factor tan δ (in 10-3) at 20 °C (upper limit values) at Insulation resistance Rins or time constant τ = CR  Rins at 20 °C, rel. humidity ≤ 65% (minimum as-delivered values) DC test voltage ≤27 nF 27 nF< CR ≤0.1 μF 0.1 μF < CR ≤1 μF 0.8 1 kHz 0.8 10 kHz 1.0 1.0 100 kHz 2.0 3.0 100 GΩ (CR ≤ 0.33 μF) 30000 s (CR > 0.33 μF) 1.6  VR, 2 s Top (°C) DC voltage derating Category voltage VC (continuous operation Top ≤ 85 VC = VR with VDC or VAC at f ≤1 kHz) 851 μF 0.8   AC voltage derating VC,RMS = VRMS VC,RMS=VRMS  (165Top)/80 Top (°C) DC voltage (max. hours) AC voltage (max. hours) Top ≤ 100 Vop = 1.25  VC (2000 h) Vop = 1.0  VC,RMS (2000 h) 100 10% > 4  upper limit values < 1500 MΩ B32671L, B32672L High V AC, high temperature (wound) Pulse handling capability "dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal voltages, expressed in V/μs. "k0" represents the maximum permissible pulse characteristic of the waveform applied to the capacitor, expressed in V2/μs. Note: The values of dV/dt and k0 provided below must not be exceeded in order to avoid damaging the capacitor. These parameters are given for isolated pulses in such a way that the heat generated by one pulse will be completely dissipated before applying the next pulse. For a train of pulses, please refer to the curves of permissible AC voltage-current versus frequency. dV/dt values Lead spacing Type VRMS (V AC) VR (V DC) CR (nF) 1.0 1.2 1.5 2.2 2.7 3.3 3.9 4.7 5.6 6.2 6.8 8.2 10 12 15 22 33 47 56 68 100 10 mm B32671L 200 250 400 630 dV/dt in V/μs                              540 400 540 400 540 400 540  540 400  400  Please read Cautions and warnings and Important notes at the end of this document. 1000 500 1000        810   810  810  810 810      Page 11 of 39      4700 4300 3800 3400 3200 3100 2700 2500 2300        600 1600  6000 5600 5200 5000 4700 4500 4000              700 2000 11000 10000 9500 9000 8600 8500 8200 8000              B32671L, B32672L High V AC, high temperature (wound) dV/dt values Lead spacing 15 mm Type B32672L VRMS (V AC) 160 200 VR (V DC) 250 450 CR (nF) dV/dt in V/μs 1.0   1.2   1.5   2.2   2.7   3.3   3.9   4.7   5.6   6.2   6.8   8.2   10   12   15   22   33   47   56   68  200 100  200 150 170 200 220 170 200 330 170 200 390   470 170 200 680 170 200 1000 170  Please read Cautions and warnings and Important notes at the end of this document. 630 250 1000 500 1300 600 1600 700 2000 900 2000                 300 300  300 300 300 300  300                445  445 445 445 445  445 445 445                 1000  1000   1000 1000 1000  1000                  3600 3500 3100 2800 2600 2300 2000 1700 1400           10000 9400 9000 7500 7100 6800 6000 5500 5000 4700 4500 4200 3900 3600 3300 2900 2300            15000 14100 13500 11000 10600 10000 9000 8200 7500 7000 6700                  Page 12 of 39 B32671L, B32672L High V AC, high temperature (wound) k0 values Lead spacing 10 mm Type B32671L VRMS (V AC) 200 VR (V DC) 400 CR (nF) k0 in V2/μs 1.0  1.2  1.5  2.2  2.7  3.3  3.9  4.7  5.6  6.2  6.8  8.2  10  12  15  22 150000 33 150000 47 150000 56  68 150000 100 150000 250 630 1000               200000 200000 200000 200000 200000          400000   400000  400000  400000 400000      Please read Cautions and warnings and Important notes at the end of this document. 500 1000      9400000 8600000 8200000 7600000 6800000 6200000 5400000 5000000 4600000        Page 13 of 39 600 1600  14400000 14000000 13800000 13600000 13300000 13100000 12000000              700 2000 25000000 23000000 22500000 22000000 21500000 21000000 20900000 20800000 B32671L, B32672L High V AC, high temperature (wound) k0 values Lead spacing Type VRMS (V AC) VR (V DC) CR (nF) 1.0 1.2 1.5 2.2 2.7 3.3 3.9 4.7 5.6 6.2 6.8 8.2 10 12 15 22 33 47 56 68 100 150 220 330 390 470 680 1000 15 mm B32672L 160 200 250 450 k0 in V2/μs                                        120000  120000 100000 120000 100000 120000 100000 120000   100000 120000 100000 100000  Please read Cautions and warnings and Important notes at the end of this document. 250 630 1000                 500000 500000  500000 500000 500000 500000  500000                1000000  1000000 1000000 1000000 1000000  1000000 1000000 1000000       500 1300 700 2000 900 2000   20300000   19600000   19200000   18600000   18200000   18000000   16800000   15800000   13100000  11520000 12700000 3000000 11200000 12300000  9920000 11800000 3000000 8960000 11100000  8320000 10600000  7360000 10400000 3000000 6400000 9300000 3000000 5440000 9000000 3000000 4480000     3000000                           30000000 29400000 28000000 27500000 27300000 27000000 25200000 23500000 19500000 19000000 18400000                  Page 14 of 39 600 1600 B32671L, B32672L High V AC, high temperature (wound) Impedance Z versus frequency f (typical values) Please read Cautions and warnings and Important notes at the end of this document. Page 15 of 39 B32671L High V AC, high temperature (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C) For TA >100 °C, please use derating factor FT. Lead spacing 10 mm 400 V DC/200 V AC 630 V DC/250 V AC 1000 V DC/250 V AC 1000 V DC/500 V AC Please read Cautions and warnings and Important notes at the end of this document. Page 16 of 39 B32671L High V AC, high temperature (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C) For TA >100 °C, please use derating factor FT. Lead spacing 10 mm 1600 V DC/600 V AC Please read Cautions and warnings and Important notes at the end of this document. 2000 V DC/700 V AC Page 17 of 39 B32672L High V AC, high temperature (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C) For TA >100 °C, please use derating factor FT. Lead spacing 15 mm 250 V DC/160 V AC 450 V DC/200 V AC 630 V DC/250 V AC 1000 V DC/250 V AC Please read Cautions and warnings and Important notes at the end of this document. Page 18 of 39 B32672L High V AC, high temperature (wound) Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C) For TA >100 °C, please use derating factor FT. Lead spacing 15 mm 1300 V DC/500 V AC 1600 V DC/600 V AC 2000 V DC/700 V AC 2000 V DC/900 V AC Please read Cautions and warnings and Important notes at the end of this document. Page 19 of 39 B32671L High V AC, high temperature (wound) Permissible current IRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C) For TA >100 °C, please use derating factor FT. Lead spacing 10 mm 400 V DC/200 V AC 630 V DC/250 V AC 1000 V DC/250 V AC 1000 V DC/500 V AC Please read Cautions and warnings and Important notes at the end of this document. Page 20 of 39 B32671L High V AC, high temperature (wound) Permissible current IRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C) For TA >100 °C, please use derating factor FT. Lead spacing 10 mm 1600 V DC/600 V AC Please read Cautions and warnings and Important notes at the end of this document. 2000 V DC/700 V AC Page 21 of 39 B32672L High V AC, high temperature (wound) Permissible current IRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C) For TA >100 °C, please use derating factor FT. Lead spacing 15 mm 250 V DC/160 V AC 450 V DC/200 V AC 630 V DC/250 V AC 1000 V DC/250 V AC Please read Cautions and warnings and Important notes at the end of this document. Page 22 of 39 B32672L High V AC, high temperature (wound) Permissible current IRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C) For TA >100 °C, please use derating factor FT. Lead spacing 15 mm 1300 V DC/500 V AC 1600 V DC/600 V AC 2000 V DC/700 V AC 2000 V DC/900 V AC Please read Cautions and warnings and Important notes at the end of this document. Page 23 of 39 B32671L, B32672L High V AC, high temperature (wound) Maximum AC voltage (VRMS), current (IRMS) versus frequency and temperature for TA >100 °C The graphs described in the previous section for the permissible AC voltage (VRMS) or current (IRMS) versus frequency are given for a maximum ambient temperature TA ≤100 ºC. In case of higher ambient temperatures (TA), the self-heating (ΔT) of the component must be reduced to avoid that temperature of the component (Top= TA + ΔT) reaches values above maximum operating temperature.The factor FT shall be applied in the following way: And FT is given by the following curve: Please read Cautions and warnings and Important notes at the end of this document. Page 24 of 39 B32671L, B32672L High V AC, high temperature (wound) Operation at overvoltages during heating and ignition of lamps (TA ≤40 °C) In lighting applications, the capacitors can be subjected to overvoltages during the heating and ignition periods. An overvoltage occurs when the operating voltage exceeds the permissible AC voltage at the resonant frequency fr. For a repetitive application of on/off switching pulses (as for example in the life tests applied by electronic ballast manufacturers), limits have to be imposed on the time periods under overvoltage and on the duty cycle, in order to keep the capacitance value within the required margins: The overvoltage time tOV should be less than 1 sec. The K0 calculated in the overvoltage period (see general technical information) shall be lower than the maximum K0 provided. The maximum duty cycle of the overvoltage is given by where VRMS,ov is the RMS voltage during period tOV and VRMS is the permissible AC voltage for continuous operation at the resonant frequency fr (given by the “permissible AC voltage versus frequency f” graphics in theprevious pages). The drift of capacitance depends on the Vpp attained, and the total time under overvoltage, which is calculated in hours as follows: (Ni  tOV) / 3600 where Ni is the number of overvoltage impulses and tOV is expressed in seconds. The maximum drift of capacitance as a function of both parameters is provided graphically in the following pages. Please read Cautions and warnings and Important notes at the end of this document. Page 25 of 39 B32671L High V AC, high temperature (wound) Estimation of the maximum drift of capacitance value in function of the number of total hours overvoltage Lead spacing 10 mm 500 V AC/1000 V DC Please read Cautions and warnings and Important notes at the end of this document. 600 V AC/1600 V DC Page 26 of 39 B32672L High V AC, high temperature (wound) Estimation of the maximum drift of capacitance value in function of the number of total hours overvoltage Lead spacing 15 mm 600 V AC/1600 V DC Please read Cautions and warnings and Important notes at the end of this document. 700 V AC/2000 V DC Page 27 of 39 B32671L, B32672L High V AC, high temperature (wound) Testing and Standards Test Reference Conditions of test Electrical parameters IEC 60384-16:2005 Voltage proof, 1.6 VR, 1 minute Insulation resistance, Rins Capacitance, C Dissipation factor, tan δ RobustIEC Tensile strength (test Ua1) ness of ter- 60068-2-21:2006 Wire diameter Tensile force minations 0.5 < d1 ≤ 0.8 mm 10 N Solder bath temperature at 260 ±5 °C, immersion for 10 seconds Performance requirements Within specified limits Capacitance and tan δ within specified limits ΔC/C0 ≤ 2% Δ tan δ ≤ 0.002 Resistance to soldering heat IEC 60068-2-20:2008, test Tb, method 1A Rapid change of temperature IEC 60384-16:2005 TA = lower category temperature TB = upper category temperature Five cycles, duration t = 30 min. Vibration IEC 60384-16:2005 Test Fc: vibration sinusoidal Displacement: 0.75 mm Accleration: 98 m/s2 Frequency: 10 Hz ... 500 Hz Test duration: 3 orthogonal axes, 2 hours each axe No visible damage Bump IEC 60384-16:2005 Test Eb: Total 4000 bumps with 390 m/s2 mounted on PCB No visible damage ΔC/C0 ≤ 2% Δ tan δ ≤ 0.002 Rins ≥ 50% of initial limit No visible damage ΔC/C0 ≤ 3% Δ tan δ ≤ 0.001 Rins ≥ 50% of initial limit Duration: 6 ms Climatic sequence Damp heat, steady state IEC 60384-16:2005 Dry heat Tb / 16 h Damp heat cyclic, 1st cycle +55 °C / 24 h / 95% ... 100% RH Cold Ta / 2 h Damp heat cyclic, 5 cycles +55 °C / 24 h / 95% ... 100% RH IEC 60384-16:2005 Test Ca 40 °C / 93% RH / 56 days Advanced biased humidity Please read Cautions and warnings and Important notes at the end of this document. No visible damage ΔC/C0 ≤ 3% Δ tan δ ≤ 0.001 Rins ≥ 50% of initial limit 60 °C / 95% RH / 1000 hours with VR,DC No visible damage ΔC/C0 ≤ 10% Δ tan δ ≤ 0.002 Rins ≥ 50% of initial limit Page 28 of 39 B32671L, B32672L High V AC, high temperature (wound) Test Reference Conditions of test Endurance IEC 60384-16:2005 85 °C / 1.25 VR / 2000 hours Endurance IEC 60384-16:2005 110 °C / 1.25 VC / 2000 hours Performance requirements No visible damage ΔC/C0 ≤ 5% Δ tan δ ≤ 0.002 Rins ≥ 50% of initial limit No visible damage ΔC/C0 ≤ 10% Δ tan δ ≤ 0.002 Rins ≥ 50% of initial limit Mounting guidelines 1 Soldering 1.1 Solderability of leads The solderability of terminal leads is tested to IEC 60068-2-20, test Ta, method 1. Before a solderability test is carried out, terminals are subjected to accelerated ageing (to IEC 60068-2-2, test Ba: 4 h exposure to dry heat at 155 °C). Since the ageing temperature is far higher than the upper category temperature of the capacitors, the terminal wires should be cut off from the capacitor before the ageing procedure to prevent the solderability being impaired by the products of any capacitor decomposition that might occur. Solder bath temperature 235 ±5 °C Soldering time 2.0 ±0.5 s Immersion depth 2.0 +0/0.5 mm from capacitor body or seating plane Evaluation criteria: Visual inspection Please read Cautions and warnings and Important notes at the end of this document. Wetting of wire surface by new solder ≥90%, free-flowing solder Page 29 of 39 B32671L, B32672L High V AC, high temperature (wound) 1.2 Resistance to soldering heat Resistance to soldering heat is tested to IEC 60068-2-20, test Tb, method 1. Conditions: Series Solder bath temperature Soldering time MKT boxed (except 2.5 × 6.5 × 7.2 mm) 260 ±5 °C coated uncoated (lead spacing >10 mm) MFP MKP (lead spacing >7.5 mm) MKT boxed (case 2.5 × 6.5 × 7.2 mm) MKP (lead spacing ≤7.5 mm) MKT uncoated (lead spacing ≤10 mm) insulated (B32559) 10 ±1 s 5 ±1 s