Film Capacitors
Metallized Polypropylene Film Capacitors (MKP)
Series/Type:
B32671P ... B32673P
Date:
November 2019
© TDK Electronics AG 2020. Reproduction, publication and dissemination of this publication, enclosures hereto
and the information contained therein without TDK Electronics' prior express consent is prohibited.
Metallized polypropylene film capacitors (MKP)
B32671P ... B32673P
Power Factor Correction
Typical applications
PFC (Power Factor Correction)
Dimensional drawing
Climatic
Max. operating temperature: 125 °C
Climatic category (IEC 60068-1:2013):
55/110/56
Construction
Dielectric: polypropylene (PP)
Wound capacitor technology
Plastic case (UL 94 V-0)
Epoxy resin sealing
Dimensions in mm
Features
Very compact design
Very small dimensions
Very high ripple and peak current
High frequency AC operation capability
High voltage capability
Excellent self-healing property
RoHS-compatible
Halogen-free capacitors available on request
AEC-Q200D compliant
Lead spacing
±0.4
10
15
22.5
Terminals
Parallel wire leads, lead free, tinned
Special lead lengths available on request
Marking
Manufacturer's logo
Lot number, series number
Rated capacitance (coded)
Capacitance tolerance (code letter)
Rated DC voltage
Date of manufacture (coded)
Delivery mode
Bulk (untaped)
Taped (Ammo pack or reel)
For notes on taping, refer to chapter "Taping and packing“.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 2 of 28
Lead diameter
d1 ±0.05
0.6
0.8
0.8
Type
B32671P
B32672P
B32673P
B32671P ... B32673P
Power Factor Correction
Overview of available types
Lead spacing 10 mm
15 mm
22.5 mm
Type
B32671P
B32672P
B32673P
Page
4
5
6
VRMS (V AC)
160
200
200
160
200
200
160
200
200
VR (V DC)
450
520
630
450
520
630
450
520
630
CR (μF)
0.068
0.082
0.10
0.15
0.18
0.22
0.27
0.33
0.39
0.47
0.56
0.68
1.0
1.5
2.0
2.2
Please read Cautions and warnings and
Important notes at the end of this document.
Page 3 of 28
B32671P
Power Factor Correction
Ordering codes and packing units (lead spacing 10 mm)
VR
V DC
450
520
630
VRMS
CR
f ≤1 kHz
V AC
μF
160
0.10
0.15
0.18
0.22
0.27
0.33
0.39
0.47
0.68
1.0
200
0.082
0.10
0.15
0.22
0.33
0.47
200
0.068
0.082
0.10
0.15
0.18
0.22
0.33
0.39
Ordering code
(composition see
below)
B32671P4104+***
B32671P4154+***
B32671P4184+***
B32671P4224+***
B32671P4274+***
B32671P4334+***
B32671P4394+***
B32671P4474+***
B32671P4684+***
B32671P4105+***
B32671P5823+***
B32671P5104+***
B32671P5154+***
B32671P5224+***
B32671P5334+***
B32671P5474+***
B32671P6683+***
B32671P6823+***
B32671P6104+***
B32671P6154+***
B32671P6184+***
B32671P6224+***
B32671P6334+***
B32671P6394+***
Max. dimensions
w×h×l
mm
4.0 × 9.0 × 13.0
4.0 × 9.0 × 13.0
5.0 × 11.0 × 13.0
5.0 × 11.0 × 13.0
5.0 × 11.0 × 13.0
6.0 × 12.0 × 13.0
6.0 × 12.0 × 13.0
6.0 × 14.0 × 13.0
7.0 × 16.0 × 13.0
8.0 × 17.5 × 13.0
4.0 × 9.0 × 13.0
5.0 × 11.0 × 13.0
5.0 × 11.0 × 13.0
6.0 × 12.0 × 13.0
7.0 × 16.0 × 13.0
8.0 × 17.5 × 13.0
4.0 × 9.0 × 13.0
5.0 × 11.0 × 13.0
5.0 × 11.0 × 13.0
6.0 × 12.0 × 13.0
6.0 × 12.0 × 13.0
6.0 × 14.0 × 13.0
8.0 × 17.5 × 13.0
8.0 × 17.5 × 13.0
Ammo
pack
pcs./MOQ
4000
4000
3320
3320
3320
2720
2720
2720
4000
3320
3320
2720
4000
3320
3320
2720
2720
2720
Reel
Untaped
pcs./MOQ
6800
6800
5200
5200
5200
4400
4400
4400
6800
5200
5200
4400
6800
5200
5200
4400
4400
4400
pcs./MOQ
4000
4000
4000
4000
4000
4000
4000
4000
4000
2000
4000
4000
4000
4000
4000
2000
4000
4000
4000
4000
4000
4000
2000
2000
MOQ = Minimum Order Quantity, consisting of 4 packing units.
Further E series, intermediate capacitance values and closer tolerance on request.
Composition of ordering code
+ = Capacitance tolerance code:
J = ±5%
K = ±10%
M = ±20%
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Packaging code:
289 = Straight terminals, Ammo pack
189 = Straight terminals, Reel
003 = Straight terminals, untaped (lead length
3.2 ± 0.3 mm)
000 = Straight terminals, untaped (lead length
61 mm)
Page 4 of 28
B32672P
Power Factor Correction
Ordering codes and packing units (lead spacing 15 mm)
VR
V DC
450
520
630
VRMS
CR
f ≤1 kHz
V AC
μF
160
0.10
0.22
0.33
0.47
0.56
0.68
1.0
1.5
2.0
2.2
200
0.15
0.22
0.33
0.47
0.68
1.0
1.5
200
0.15
0.22
0.33
0.47
0.68
1.0
Ordering code
(composition see
below)
B32672P4104+***
B32672P4224+***
B32672P4334+***
B32672P4474+***
B32672P4564+***
B32672P4684+***
B32672P4105+***
B32672P4155+***
B32672P4205+***
B32672P4225+***
B32672P5154+***
B32672P5224+***
B32672P5334+***
B32672P5474+***
B32672P5684+***
B32672P5105+***
B32672P5155+***
B32672P6154+***
B32672P6224+***
B32672P6334+***
B32672P6474+***
B32672P6684+***
B32672P6105+***
Max. dimensions
w×h×l
mm
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
6.0 × 11.0 × 18.0
6.0 × 12.0 × 18.0
7.0 × 12.5 × 18.0
9.0 × 17.5 × 18.0
9.0 × 17.5 × 18.0
11.0 × 18.5 × 18.0
5.0 × 10.5 × 18.0
5.0 × 10.5 × 18.0
6.0 × 11.0 × 18.0
7.0 × 12.5 × 18.0
8.5 × 14.5 × 18.0
9.0 × 17.5 × 18.0
11.0 × 18.5 × 18.0
5.0 × 10.5 × 18.0
6.0 × 11.0 × 18.0
7.0 × 12.5 × 18.0
8.0 × 14.0 × 18.0
9.0 × 17.5 × 18.0
11.0 × 18.5 × 18.0
Ammo
pack
pcs./MOQ
4680
4680
4680
4680
3840
3840
3320
2560
2560
4680
4680
3840
3320
2720
2560
4680
3840
3320
2920
2560
Reel
Untaped
pcs./MOQ
5200
5200
5200
5200
4400
4400
3600
2800
2800
2200
5200
5200
4400
3600
2800
2800
2200
5200
4400
3600
3000
2800
2200
pcs./MOQ
4000
4000
4000
4000
4000
4000
4000
2000
2000
1200
4000
4000
4000
4000
2000
2000
1200
4000
4000
4000
2000
2000
1200
MOQ = Minimum Order Quantity, consisting of 4 packing units.
Further E series, intermediate capacitance values and closer tolerance on request.
Composition of ordering code
+ = Capacitance tolerance code:
J = ±5%
K = ±10%
M = ±20%
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Packaging code:
289 = Straight terminals, Ammo pack
189 = Straight terminals, Reel
003 = Straight terminals, untaped (lead length
3.2 ± 0.3 mm)
000 = Straight terminals, untaped (lead length
61 mm)
Page 5 of 28
B32673P
Power Factor Correction
Ordering codes and packing units (lead spacing 22.5 mm)
VR
V DC
450
520
630
VRMS
CR
f ≤1 kHz
V AC
μF
160
1.0
1.5
2.2
200
0.47
0.56
0.68
1.0
1.5
2.2
200
0.33
0.47
0.56
0.68
1.0
1.5
2.2
Ordering code
(composition see
below)
B32673P4105+***
B32673P4155+***
B32673P4225+***
B32673P5474+***
B32673P5564+***
B32673P5684+***
B32673P5105+***
B32673P5155+***
B32673P5225+***
B32673P6334+***
B32673P6474+***
B32673P6564+***
B32673P6684+***
B32673P6105+***
B32673P6155+***
B32673P6225+***
Max. dimensions
w×h×l
mm
6.0 × 15.0 × 26.5
7.0 × 16.0 × 26.5
8.5 × 16.5 × 26.5
6.0 × 15.0 × 26.5
6.0 × 15.0 × 26.5
6.0 × 15.0 × 26.5
7.0 × 16.0 × 26.5
10.5 × 16.5 × 26.5
10.5 × 20.5 × 26.5
6.0 × 15.0 × 26.5
6.0 × 15.0 × 26.5
6.0 × 15.0 × 26.5
7.0 × 16.0 × 26.5
8.5 × 16.5 × 26.5
10.5 × 18.5 × 26.5
12.0 × 22.0 × 26.5
Ammo
pack
pcs./MOQ
2720
2320
1920
2720
2720
2720
2320
1560
2720
2720
2720
2320
1920
1560
Reel
Untaped
pcs./MOQ
2800
2400
2000
2800
2800
2800
2400
1600
2800
2800
2800
2400
2000
1600
pcs./MOQ
2880
2520
2040
2880
2880
2880
2520
2160
2160
2880
2880
2880
2520
2040
2160
1800
MOQ = Minimum Order Quantity, consisting of 4 packing units.
Further E series, intermediate capacitance values and closer tolerance on request.
Composition of ordering code
+ = Capacitance tolerance code:
J = ±5%
K = ±10%
M = ±20%
Please read Cautions and warnings and
Important notes at the end of this document.
*** = Packaging code:
289 = Straight terminals, Ammo pack
189 = Straight terminals, Reel
003 = Untaped (lead length 3.2 ± 0.3 mm)
000 = Untaped (lead length 61 mm)
Page 6 of 28
B32671P ... B32673P
Power Factor Correction
Technical data
Reference standard: IEC 60384-16:2005 and AEC-Q200D. All data given at T = 20 °C, unless
otherwise specified.
Rated temperature TR
+85 °C
Operating temperature
range
Dissipation factor tan δ
(in 10-3) at 20 °C
(upper limit values)
Insulation resistance Rins
at 100 V or time constant
τ = CR Rins at 20 °C,
rel. humidity ≤ 65%
(minimum as-delivered
values)
Max. operating temperature Top, max
Upper category temperature Tmax
Lower category temperature Tmin
Rated temperature TR
at
1 kHz: 1.0
at 10 kHz: 2.5
at 100 kHz: 25.0
+125 °C
+110 °C
55 °C
+85 °C
30 GΩ (CR ≤ 0.33 μF)
10000 s (CR > 0.33 μF)
1.4 VR, 2 s
Category voltage VC
Top (°C)
DC voltage derating
AC voltage derating
(continuous operation with Top ≤85
V C = VR
VC,RMS = VRMS
VDC or VAC at f ≤ 1 kHz)
85 4 upper limit values
Insulation resistance Rins
< 150 MΩ (CR ≤ 0.33 μF)
< 50 s (CR ≥ 0.33 μF)
Or time constant τ
DC test voltage
Please read Cautions and warnings and
Important notes at the end of this document.
Page 7 of 28
B32671P ... B32673P
Power Factor Correction
Pulse handling capability
"dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal
voltages, expressed in V/μs.
"k0" represents the maximum permissible pulse characteristic of the waveform applied to the
capacitor, expressed in V2/μs.
Note:
The values of dV/dt and k0 provided below must not be exceeded in order to avoid damaging the
capacitor. These parameters are given for isolated pulses in such a way that the heat generated
by one pulse will be completely dissipated before applying the next pulse. For a train of pulses,
please refer to the curves of permissible AC voltage-current versus frequency.
dV/dt values
Lead spacing
VR
VRMS
V DC V AC
450
160
520
200
630
200
10 mm
15 mm
22.5 mm
dV/dt in V/μs
140
200
250
120
160
180
100
110
130
10 mm
15 mm
22.5 mm
k0 in V2/μs
126000
208000
315000
108000
166000
226000
90000
114000
163000
k0 values
Lead spacing
VR
VRMS
V DC V AC
450
160
520
200
630
200
Please read Cautions and warnings and
Important notes at the end of this document.
Page 8 of 28
B32671P ... B32673P
Power Factor Correction
Impedance Z versus frequency f
(typical values)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 9 of 28
B32671P
Power Factor Correction
Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C)
For TA >100 °C, please use derating factor FT.
Lead spacing 10 mm
450 V DC/160 V AC
520 V DC/200 V AC
630 V DC/200 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
Page 10 of 28
B32672P
Power Factor Correction
Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C)
For TA >100 °C, please use derating factor FT.
Lead spacing 15 mm
450 V DC/160 V AC
520 V DC/200 V AC
630 V DC/200 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
Page 11 of 28
B32673P
Power Factor Correction
Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C)
For TA >100 °C, please use derating factor FT.
Lead spacing 22.5 mm
450 V DC/160 V AC
520 V DC/200 V AC
630 V DC/200 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
Page 12 of 28
B32671P
Power Factor Correction
Permissible AC current IRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C)
For TA >100 °C, please use derating factor FT.
Lead spacing 10 mm
450 V DC/160 V AC
520 V DC/200 V AC
630 V DC/200 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
Page 13 of 28
B32672P
Power Factor Correction
Permissible AC current IRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C)
For TA >100 °C, please use derating factor FT.
Lead spacing 15 mm
450 V DC/160 V AC
520 V DC/200 V AC
630 V DC/200 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
Page 14 of 28
B32673P
Power Factor Correction
Permissible AC current IRMS versus frequency f (for sinusoidal waveforms TA ≤100 °C)
For TA >100 °C, please use derating factor FT.
Lead spacing 22.5 mm
450 V DC/160 V AC
520 V DC/200 V AC
630 V DC/200 V AC
Please read Cautions and warnings and
Important notes at the end of this document.
Page 15 of 28
B32671P ... B32673P
Power Factor Correction
Maximum AC voltage (VRMS), current (IRMS) versus frequency and temperature for TA >100 °C
The graphs described in the previous section for the permissible AC voltage (VRMS) or current
(IRMS) versus frequency are given for a maximum ambient temperature TA ≤100 ºC. In case of
higher ambient temperatures (TA), the self-heating (ΔT) of the component must be reduced to
avoid that temperature of the component (Top= TA + ΔT) reaches values above maximum
operating temperature.The factor FT shall be applied in the following way:
And FT is given by the following curve:
Please read Cautions and warnings and
Important notes at the end of this document.
Page 16 of 28
B32671P ... B32673P
Power Factor Correction
Testing and Standards
Test
Reference
Conditions of test
Performance
requirements
Electrical
parameters
IEC
60384-16:2005
Within specified limits
Robustness
of terminations
IEC
60068-2-21:2006
Voltage proof, 1.4 VR, 1 minute
Insulation resistance, Rins
Capacitance, C
Dissipation factor, tan δ
Tensile strength (test Ua1)
Wire diameter
Tensile force
0.5 < d1 ≤ 0.8 mm 10 N
Capacitance and tan δ
within specified limits
Solder bath temperature at 260 ±5 °C, ΔC/C0 ≤ 2%
Resistance to IEC
60068-2-20:2008, immersion for 10 seconds
soldering
Δ tan δ ≤ 0.001
test Tb,
heat
method 1A
ΔC/C0 ≤ 2%
Rapid
IEC
TA = lower category temperature
Δ
tan δ ≤ 0.002
change of
60384-16:2005
TB = upper category temperature
Rins ≥ 50% of initial limit
temperature
Five cycles, duration t = 30 min.
Vibration
IEC
60384-16:2005
Test FC: vibration sinusoidal
Displacement: 0.75 mm
Accleration: 98 m/s2
Frequency: 10 Hz ... 500 Hz
Test duration: 3 orthogonal axes,
2 hours each axe
No visible damage
Bump
IEC
60384-16:2005
Test Eb: Total 4000 bumps with
390 m/s2 mounted on PCB
No visible damage
ΔC/C0 ≤ 2%
Δ tan δ ≤ 0.001
Rins ≥ 50% of initial limit
No visible damage
ΔC/C0 ≤ 2%
Δ tan δ ≤ 0.001
Rins ≥ 50% of initial limit
Duration: 6 ms
Climatic
sequence
IEC
60384-16:2005
Damp heat,
steady state
IEC
60384-16:2005
Advanced
biased
humidity
Please read Cautions and warnings and
Important notes at the end of this document.
Dry heat Tb / 16 h
Damp heat cyclic, 1st cycle
+55 °C / 24 h / 95% ... 100% RH
Cold Ta / 2 h
Damp heat cyclic, 5 cycles
+55 °C / 24 h / 95% ... 100% RH
Test Ca
40 °C / 93% RH / 56 days
60 °C / 95% RH / 1000 hours
with VR,DC
Page 17 of 28
No visible damage
ΔC/C0 ≤ 3%
Δ tan δ ≤ 0.003
Rins ≥ 50% of initial limit
No visible damage
ΔC/C0 ≤ 10%
Δ tan δ ≤ 0.004
Rins ≥ 50% of initial limit
B32671P ... B32673P
Power Factor Correction
Test
Reference
Endurance A
Endurance B
Endurance C
Endurance D
Conditions of test
Performance
requirements
No visible damage
85 °C / 1.1 VR / 1000 hours
ΔC/C0 ≤ 5%
Δ tan δ ≤ 0.004
Rins ≥ 50% of initial limit
No visible damage
110 °C / 1.1 VC / 1000 hours
ΔC/C0 ≤ 10%
Δ tan δ ≤ 0.004
Rins ≥ 50% of initial limit
No visible damage
125 °C / 1.1 VC / 1000 hours
ΔC/C0 ≤ 10%
Δ tan δ ≤ 0.004
Rins ≥ 50% of initial limit
85 °C/ VR + 4 ARMS,1000 KHz/ 1000 hours No visible damage
ΔC/C0 ≤ 10%
Δ tan δ ≤ 0.004
Rins ≥ 50% of initial limit
Mounting guidelines
1
Soldering
1.1
Solderability of leads
The solderability of terminal leads is tested to IEC 60068-2-20, test Ta, method 1.
Before a solderability test is carried out, terminals are subjected to accelerated ageing (to
IEC 60068-2-2, test Ba: 4 h exposure to dry heat at 155 °C). Since the ageing temperature is far
higher than the upper category temperature of the capacitors, the terminal wires should be cut off
from the capacitor before the ageing procedure to prevent the solderability being impaired by the
products of any capacitor decomposition that might occur.
Solder bath temperature
235 ±5 °C
Soldering time
2.0 ±0.5 s
Immersion depth
2.0 +0/0.5 mm from capacitor body or seating plane
Evaluation criteria:
Visual inspection
Please read Cautions and warnings and
Important notes at the end of this document.
Wetting of wire surface by new solder ≥90%,
free-flowing solder
Page 18 of 28
B32671P ... B32673P
Power Factor Correction
1.2
Resistance to soldering heat
Resistance to soldering heat is tested to IEC 60068-2-20, test Tb, method 1.
Conditions:
Series
Solder bath temperature Soldering time
MKT boxed (except 2.5 × 6.5 × 7.2 mm) 260 ±5 °C
coated
uncoated (lead spacing >10 mm)
MFP
MKP (lead spacing >7.5 mm)
MKT boxed (case 2.5 × 6.5 × 7.2 mm)
MKP (lead spacing ≤7.5 mm)
MKT uncoated (lead spacing ≤10 mm)
insulated (B32559)
10 ±1 s
5 ±1 s