B41554E9228Q

Aluminum Electrolytic Capacitors with Screw Terminals Series/Type: B41554 The following products presented in this data sheet are being withdrawn. Ordering Code B41554E9688Q000 B41554E9478Q000 B41554E9159Q000 Substitute Product Date of Withdrawal 2017-11-17 2017-11-17 2017-11-17 Deadline Last Orders 2018-11-17 2018-11-17 2018-11-17 Last Shipments 2019-05-17 2019-05-17 2019-05-17 Ordering Code B41554E9109Q000 B41554E8339Q000 B41554E8229Q000 B41554E8159Q000 B41554E8109Q000 B41554E7689Q000 B41554E7479Q000 B41554E7339Q000 B41554E7229Q000 B41554E5689Q000 B41554E5479Q000 B41554E5339Q000 B41554E5100Q000 B41554E4689Q000 B41554E4479Q000 B41554E4150Q000 B41554E4100Q000 B41554B9339Q000 B41554B9229Q000 B41554B8479Q000 B41554B7100Q000 B41554B5150Q000 B41554B4220Q000 Substitute Product Date of Withdrawal 2017-11-17 2017-11-17 2017-11-17 2017-11-17 2017-11-17 2017-11-17 2017-11-17 2017-11-17 2017-11-17 2017-11-17 2017-11-17 2017-11-17 2017-11-17 2017-11-17 2017-11-17 2017-11-17 2017-11-17 2017-11-17 2017-11-17 2017-11-17 2017-11-17 2017-11-17 2017-11-17 Deadline Last Orders 2018-11-17 2018-11-17 2018-11-17 2018-11-17 2018-11-17 2018-11-17 2018-11-17 2018-11-17 2018-11-17 2018-11-17 2018-11-17 2018-11-17 2018-11-17 2018-11-17 2018-11-17 2018-11-17 2018-11-17 2018-11-17 2018-11-17 2018-11-17 2018-11-17 2018-11-17 2018-11-17 Last Shipments 2019-05-17 2019-05-17 2019-05-17 2019-05-17 2019-05-17 2019-05-17 2019-05-17 2019-05-17 2019-05-17 2019-05-17 2019-05-17 2019-05-17 2019-05-17 2019-05-17 2019-05-17 2019-05-17 2019-05-17 2019-05-17 2019-05-17 2019-05-17 2019-05-17 2019-05-17 2019-05-17 For further information please contact your nearest EPCOS sales office, which will also support you in selecting a suitable substitute. The addresses of our worldwide sales network are presented at www.epcos.com/sales. Aluminum Electrolytic Capacitors with Screw Terminals SIKOREL  125 °C Long-life grade capacitors Applications Highly professional power supplies Features Outstanding reliability Wide temperature range Good thermal characteristics and high ripple current capability Long useful life SIKOREL design  storage for up to 10 years at a temperature of up to 35 °C All-welded construction ensures reliable electrical contact RoHS-compatible Construction Charge-discharge proof, polar Aluminum case, fully insulated with PET Poles with screw terminal connections Mounting with ring clips or clamps Please read Cautions and warnings and Important notes at the end of this document. Page 2 of 17 B41554 SIKOREL  125 °C Specifications and characteristics in brief Rated voltage VR Surge voltage VS Rated capacitance CR Capacitance tolerance 16 ... 100 V DC 1.15  VR 4700 ... 220000 μF 10/+30%  Q Leakage current Ileak (5 min, 20 °C) Self-inductance ESL d = 51.6 mm: approx. 15 nH d ≥ 64.3 mm: approx. 20 nH Useful life1) 125 °C; VR; IAC,R 85 °C; VR; IAC,max 40 °C; VR; 3.4  IAC,R 40 °C; VR; 3.8  IAC,R Voltage endurance test 125 °C; VR; IAC,R d = 51.6 mm > 2500 h > 15000 h > 200000 h  d ≥ 64.3 mm > 5000 h > 25000 h  > 200000 h Requirements: ΔC/C ≤ 45% of initial value ESR ≤ 3 times initial specified limit Ileak ≤ initial specified limit Post test requirements: ΔC/C ≤ 15% of initial value ESR ≤ 1.3 times initial specified limit Ileak ≤ initial specified limit 2000 h Vibration resistance test To IEC 60068-2-6, test Fc: Frequency range 10 ... 55 Hz, displacement amplitude 0.75 mm, acceleration max. 10 g, duration 3 × 2 h. Capacitor mounted by its body which is rigidly clamped to the work surface. IEC climatic category To IEC 60068-1: 55/125/56 (55 °C/+125 °C/56 days damp heat test) Detail specification Sectional specification Similar to CECC 30301-804 IEC 60384-4 Ripple current capability Due to the ripple current capability of the contact elements, the following current upper limits must not be exceeded: Capacitor diameter 51.6 mm > 51.6 mm IAC, max 30 A 40 A 1) Refer to chapter "General technical information, 5 Useful life" on how to interpret useful life. Please read Cautions and warnings and Important notes at the end of this document. Page 3 of 17 B41554 SIKOREL  125 °C Dimensional drawings Dimensions and weights Terminal Dimensions (mm) with insulating sleeve d l ±1 l1 ±1 d2 max. M5 51.6 +0.5/1 80.7 87.0 8.2 22.2 220 M5 M5 M5 M5 64.3 +0.5/1 64.3 +0.5/1 76.9 +0.5/1 76.9 +0.5/1 80.7 105.7 105.7 143.2 87.0 112.0 112.0 149.5 8.2 8.2 8.2 8.2 28.5 28.5 31.7 31.7 370 440 620 840 Tolerances of terminal thread M5: 6H Please read Cautions and warnings and Important notes at the end of this document. Page 4 of 17 a +0.2/0.4 Approx. weight (g) B41554 SIKOREL  125 °C Packing Capacitor diameter d (mm) 51.6 64.3 76.9 Length l (mm) all all all Packing units (pcs.) 36 25 16 For ecological reasons the packing is pure cardboard. Accessories The following items are included in the delivery package, but are not fastened to the capacitors: For terminals Thread Toothed washers Screws/nuts Maximum torque M5 DIN 7985 / ISO 7045-M5 × 10-5.6-Z 2 Nm A 5.1 DIN 6797 The following items must be ordered separately. For details, refer to chapter "Capacitors with screw terminals  Accessories". Item Type Ring clips B44030 Clamps for capacitors with d ≥ 64.3 mm B44030 Please read Cautions and warnings and Important notes at the end of this document. Page 5 of 17 B41554 SIKOREL  125 °C Overview of available types The capacitance and voltage ratings listed below are available in different case sizes upon request. Other voltage and capacitance ratings are also available upon request. VR (V DC) 16 25 40 63 100 Case dimensions d × l (mm) CR (μF) 4700 51.6 × 80.7 6800 64.3 × 80.7 10000 51.6 × 80.7 64.3 × 80.7 15000 64.3 × 80.7 64.3 × 105.7 51.6 × 80.7 64.3 × 105.7 76.9 × 105.7 51.6 × 80.7 64.3 × 80.7 76.9 × 105.7 76.9 × 143.2 76.9 × 143.2 22000 33000 47000 51.6 × 80.7 64.3 × 80.7 64.3 × 105.7 68000 64.3 × 80.7 64.3 × 105.7 76.9 × 105.7 100000 64.3 × 105.7 76.9 × 105.7 76.9 × 143.2 150000 76.9 × 105.7 76.9 × 143.2 220000 76.9 × 143.2 Please read Cautions and warnings and Important notes at the end of this document. Page 6 of 17 B41554 SIKOREL  125 °C Technical data and ordering codes CR 100 Hz 20 °C μF Case dimensions d×l mm VR = 16 V DC 47000 51.6 × 80.7 68000 64.3 × 80.7 100000 64.3 × 105.7 150000 76.9 × 105.7 220000 76.9 × 143.2 VR = 25 V DC 33000 51.6 × 80.7 47000 64.3 × 80.7 68000 64.3 × 105.7 100000 76.9 × 105.7 150000 76.9 × 143.2 VR = 40 V DC 22000 51.6 × 80.7 33000 64.3 × 80.7 47000 64.3 × 105.7 68000 76.9 × 105.7 100000 76.9 × 143.2 VR = 63 V DC 10000 51.6 × 80.7 15000 64.3 × 80.7 22000 64.3 × 105.7 33000 76.9 × 105.7 47000 76.9 × 143.2 VR = 100 V DC 4700 51.6 × 80.7 6800 64.3 × 80.7 10000 64.3 × 80.7 15000 64.3 × 105.7 22000 76.9 × 105.7 33000 76.9 × 143.2 ESRtyp 100 Hz 20 °C mΩ ESRmax 100 Hz 20 °C mΩ Zmax 20 kHz 20 °C mΩ IAC,max 100 Hz 40 °C A IAC,max 100 Hz 85 °C A IAC,R Ordering code 100 Hz 125 °C A 5.0 4.0 4.0 4.0 3.0 13 13 10 10 8.0 13 11 9.0 8.0 7.0 30 40 40 40 40 30 38 39 40 40 11 14 14 16 19 B41554E4479Q000 B41554E4689Q000 B41554E4100Q000 B41554E4150Q000 B41554B4220Q000 6.0 5.0 5.0 4.0 4.0 15 13 11 9.0 7.0 12 11 9.0 8.0 6.0 30 40 40 40 40 29 34 35 39 40 10 12 13 15 19 B41554E5339Q000 B41554E5479Q000 B41554E5689Q000 B41554E5100Q000 B41554B5150Q000 6.0 5.0 5.0 4.0 4.0 15 11 10 9.0 7.0 12 10 9.0 8.0 6.0 30 40 40 40 40 29 34 35 39 40 10 12 13 15 19 B41554E7229Q000 B41554E7339Q000 B41554E7479Q000 B41554E7689Q000 B41554B7100Q000 7.0 6.0 5.0 4.0 4.0 18 15 12 9.0 7.0 14 11 9.0 8.0 6.0 30 40 40 40 40 27 31 35 39 40 9.6 11 13 15 19 B41554E8109Q000 B41554E8159Q000 B41554E8229Q000 B41554E8339Q000 B41554B8479Q000 13 8.0 7.0 6.0 5.0 4.0 29 22 15 13 11 9.0 20 17 14 11 9.0 8.0 29 36 40 40 40 40 20 25 30 36 39 40 7.2 9.1 11 13 14 17 B41554E9478Q000 B41554E9688Q000 B41554E9109Q000 B41554E9159Q000 B41554B9229Q000 B41554B9339Q000 Please read Cautions and warnings and Important notes at the end of this document. Page 7 of 17 B41554 SIKOREL  125 °C Useful life1) depending on ambient temperature TA under ripple current operating conditions d = 51.6 mm Useful life1) depending on ambient temperature TA under ripple current operating conditions d ≥ 64.3 mm 1) Refer to chapter "General technical information, 5 Useful life" on how to interpret useful life. Please read Cautions and warnings and Important notes at the end of this document. Page 8 of 17 B41554 SIKOREL  125 °C Frequency factor of permissible ripple current IAC versus frequency f VR (V DC) 16; 25 40 63 100 d = 51.6 mm a b c c d = 64.3 mm a a c c d = 76.9 mm a a b c VR (V DC) 16; 25 40 63 100 d = 51.6 mm a b c c d = 64.3 mm a a c c d = 76.9 mm a a b c Frequency characteristics of ESR Typical behavior Please read Cautions and warnings and Important notes at the end of this document. Page 9 of 17 B41554 SIKOREL  125 °C Impedance Z versus frequency f Typical behavior at 20 °C CR μF Please read Cautions and warnings and Important notes at the end of this document. VR V DC d mm Curve 150000 68000 16 40 76.9 76.9 a b 15000 100 64.3 c Page 10 of 17 B41554 SIKOREL  125 °C Cautions and warnings Personal safety The electrolytes used by EPCOS have been optimized both with a view to the intended application and with regard to health and environmental compatibility. They do not contain any solvents that are detrimental to health, e.g. dimethyl formamide (DMF) or dimethyl acetamide (DMAC). Furthermore, some of the high-voltage electrolytes used by EPCOS are self-extinguishing. As far as possible, EPCOS does not use any dangerous chemicals or compounds to produce operating electrolytes, although in exceptional cases, such materials must be used in order to achieve specific physical and electrical properties because no alternative materials are currently known. We do, however, restrict the amount of dangerous materials used in our products to an absolute minimum. Materials and chemicals used in EPCOS aluminum electrolytic capacitors are continuously adapted in compliance with the EPCOS Corporate Environmental Policy and the latest EU regulations and guidelines such as RoHS, REACH/SVHC, GADSL, and ELV. MDS (Material Data Sheets) are available on the EPCOS website for all types listed in the data book. MDS for customer specific capacitors are available upon request. MSDS (Material Safety Data Sheets) are available for all of our electrolytes upon request. Nevertheless, the following rules should be observed when handling aluminum electrolytic capacitors: No electrolyte should come into contact with eyes or skin. If electrolyte does come into contact with the skin, wash the affected areas immediately with running water. If the eyes are affected, rinse them for 10 minutes with plenty of water. If symptoms persist, seek medical treatment. Avoid inhaling electrolyte vapor or mists. Workplaces and other affected areas should be well ventilated. Clothing that has been contaminated by electrolyte must be changed and rinsed in water. Please read Cautions and warnings and Important notes at the end of this document. Page 11 of 17 B41554 SIKOREL  125 °C Product safety The table below summarizes the safety instructions that must be observed without fail. A detailed description can be found in the relevant sections of chapter "General technical information". Topic Polarity Reverse voltage Mounting position of screwterminal capacitors Robustness of terminals Mounting of single-ended capacitors Soldering Soldering, cleaning agents Upper category temperature Passive flammability Safety information Reference chapter "General technical information" Make sure that polar capacitors are connected 1 with the right polarity. "Basic construction of aluminum electrolytic capacitors" Voltages of opposite polarity should be prevented 3.1.6 by connecting a diode. "Reverse voltage" Screw terminal capacitors must not be mounted 11.1. with terminals facing down unless otherwise "Mounting positions of specified. capacitors with screw terminals" The following maximum tightening torques must 11.3 not be exceeded when connecting screw "Mounting torques" terminals: M5: 2.5 Nm M6: 4.0 Nm The internal structure of single-ended capacitors 11.4 might be damaged if excessive force is applied to "Mounting the lead wires. considerations for Avoid any compressive, tensile or flexural stress. single-ended capacitors" Do not move the capacitor after soldering to PC board. Do not pick up the PC board by the soldered capacitor. Do not insert the capacitor on the PC board with a hole space different to the lead space specified. Do not exceed the specified time or temperature 11.5 limits during soldering. "Soldering" Do not allow halogenated hydrocarbons to come 11.6 into contact with aluminum electrolytic capacitors. "Cleaning agents" Do not exceed the upper category temperature. 7.2 "Maximum permissible operating temperature" Avoid external energy, e.g. fire. 8.1 "Passive flammability" Please read Cautions and warnings and Important notes at the end of this document. Page 12 of 17 B41554 SIKOREL  125 °C Topic Safety information Active flammability Maintenance Avoid overload of the capacitors. Storage Make periodic inspections of the capacitors. Before the inspection, make sure that the power supply is turned off and carefully discharge the capacitors. Do not apply excessive mechanical stress to the capacitor terminals when mounting. Do not store capacitors at high temperatures or high humidity. Capacitors should be stored at +5 to +35 °C and a relative humidity of ≤ 75%. Breakdown strength Do not damage the insulating sleeve, especially of insulating when ring clips are used for mounting. sleeves Reference chapter "General technical information" 8.2 "Active flammability" 10 "Maintenance" 7.3 "Shelf life and storage conditions" Reference chapter "Capacitors with screw terminals" "Screw terminals  accessories" Display of ordering codes for EPCOS products The ordering code for one and the same product can be represented differently in data sheets, data books, other publications and the website of EPCOS, or in order-related documents such as shipping notes, order confirmations and product labels. The varying representations of the ordering codes are due to different processes employed and do not affect the specifications of the respective products. Detailed information can be found on the Internet under www.epcos.com/orderingcodes. Please read Cautions and warnings and Important notes at the end of this document. Page 13 of 17 B41554 SIKOREL  125 °C Symbols and terms Symbol English German C CR CS CS,T Cf d dmax ESL ESR ESRf Capacitance Rated capacitance Series capacitance Series capacitance at temperature T Capacitance at frequency f Case diameter, nominal dimension Maximum case diameter Self-inductance Equivalent series resistance Equivalent series resistance at frequency f Equivalent series resistance at temperature T Frequency Current Alternating current (ripple current) Root-mean-square value of alternating current Ripple current at frequency f Maximum permissible ripple current Rated ripple current Leakage current Operating leakage current Case length, nominal dimension Maximum case length (without terminals and mounting stud) Resistance Insulation resistance Balancing resistance Temperature Temperature difference Ambient temperature Case temperature Capacitor base temperature Time Period Service life (operating hours) Kapazität Nennkapazität Serienkapazität Serienkapazität bei Temperatur T Kapazität bei Frequenz f Gehäusedurchmesser, Nennmaß Maximaler Gehäusedurchmesser Eigeninduktivität Ersatzserienwiderstand Ersatzserienwiderstand bei Frequenz f ESRT f I IAC IAC,RMS IAC,f IAC,max IAC,R Ileak Ileak,op l lmax R Rins Rsymm T ΔT TA TC TB t Δt tb Please read Cautions and warnings and Important notes at the end of this document. Ersatzserienwiderstand bei Temperatur T Frequenz Strom Wechselstrom Wechselstrom, Effektivwert Wechselstrom bei Frequenz f Maximal zulässiger Wechselstrom Nennwechselstrom Reststrom Betriebsreststrom Gehäuselänge, Nennmaß Maximale Gehäuselänge (ohne Anschlüsse und Gewindebolzen) Widerstand Isolationswiderstand Symmetrierwiderstand Temperatur Temperaturdifferenz Umgebungstemperatur Gehäusetemperatur Temperatur des Gehäusebodens Zeit Zeitraum Brauchbarkeitsdauer (Betriebszeit) Page 14 of 17 B41554 SIKOREL  125 °C Symbol V VF Vop VR VS XC XL Z ZT tan δ λ ε0 εr ω English Voltage Forming voltage Operating voltage Rated voltage, DC voltage Surge voltage Capacitive reactance Inductive reactance Impedance Impedance at temperature T Dissipation factor Failure rate Absolute permittivity Relative permittivity Angular velocity; 2  π  f German Spannung Formierspannung Betriebsspannung Nennspannung, Gleichspannung Spitzenspannung Kapazitiver Blindwiderstand Induktiver Blindwiderstand Scheinwiderstand Scheinwiderstand bei Temperatur T Verlustfaktor Ausfallrate Elektrische Feldkonstante Dielektrizitätszahl Kreisfrequenz; 2  π  f Note All dimensions are given in mm. Please read Cautions and warnings and Important notes at the end of this document. Page 15 of 17 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule we are either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether a product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.tdk-electronics.tdk.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to our General Terms and Conditions of Supply. 7. Our manufacturing sites serving the automotive business apply the IATF 16949 standard. The IATF certifications confirm our compliance with requirements regarding the quality management system in the automotive industry. Referring to customer requirements and customer specific requirements (“CSR”) TDK always has and will continue to have the policy of respecting individual agreements. Even if IATF 16949 may appear to support the acceptance of unilateral requirements, we hereby like to emphasize that only requirements mutually agreed upon can and will be implemented in our Quality Management System. For clarification purposes we like to point out that obligations from IATF 16949 shall only become legally binding if individually agreed upon. Page 16 of 17 Important notes 8. The trade names EPCOS, CeraCharge, CeraDiode, CeraLink, CeraPad, CeraPlas, CSMP, CTVS, DeltaCap, DigiSiMic, ExoCore, FilterCap, FormFit, LeaXield, MiniBlue, MiniCell, MKD, MKK, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, PowerHap, PQSine, PQvar, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.tdk-electronics.tdk.com/trademarks. Release 2018-10 Page 17 of 17