B65671_06

Ferrites and accessories P 26 × 16 Core and accessories Series/Type: Date: B65671, B65672, B65675, B65679 September 2006 Data Data Sheet  EPCOS AG 2006. Reproduction, publication and dissemination of this data sheet and the information contained therein without EPCOS’ prior express consent is prohibited. P 26 × 16 Core ■ To IEC 60133 ■ Delivery mode: sets B65671 17,7 _ 0,7 with without center hole center hole Σ l/ A le Ae Amin Ve 0.4 37.2 93 76.5 3460 0.37 40 108 87 4320 mm–1 mm mm2 mm2 mm3 21,2+0,8 3,9+0,6 Magnetic characteristics (per set) 26 _ 1 0,6+0,2 ø11,5 _ 0,4 3,1±0,15 ø5,4+0,2 16,3 _ 0,4 11+0,4 Approx. weight (per set) m Gapped Material AL value nH K1 M33 N48 100 ±3% 100 ±3% 160 ±3% 160 ±3% 250 ±3% 315 ±3% 400 ±3% 630 ±3% 800 ±3% 1000 ±5% s approx. mm 0.90 1.52 0.78 0.80 0.40 0.34 0.24 0.15 0.11 0.10 µe 21 23 g M3 FPK0136-N Ordering code 1) -D with center hole -T with threaded sleeve B65671+0100A001 B65671+0100A033 B65671+0160A033 B65671+0160A048 B65671+0250A048 B65671+0315A048 B65671+0400A048 B65671+0630A048 B65671+0800A048 B65671D1000J048 32 32 51 51 80 100 127 201 255 318 Ungapped Material AL value nH N48 N30 T38 N87 4900 +30/–20% 1560 9700 +30/–20% 2860 22000 +40/–30% 6480 5500 +30/–20% 1620 µe PV W/set Ordering code -D with center hole -W without center hole B65671D0000R048 B65671W0000R030 B65671W0000Y038 < 1.9 (200 mT, 100 kHz, 100 °C) B65671W0000R087 1) Replace the + by the code letter ”D“ or ”T“ for the required version. Please read Cautions and warnings and Important notes at the end of this document. 2 09/06 s P 26 × 16 Accessories Coil former Standard: Material: to IEC 60133 GFR polyterephthalate (UL 94 V-0, insulation class to IEC 60085: F max. operating temperature 155 °C), color code black Valox 420-SE0 ® [E45329 (M)], GE PLASTICS B V see Data Book 2007, chapter “Processing notes, 2.1” B65672 Winding: Insulating washer between core and coil former ■ For tolerance compensation and for insulation ■ Polycarbonate spring washer (UL 94 V-0, insulation class to IEC 60085: E 120 °C), 0.08 mm thick Aryphan F685, [E167358 (M)], natural color, LOFO HIGH TECH FILM GMBH Ordering code AN mm2 32.0 lN mm 52 AR value µΩ 55 B65672B0000T001 B65672B5000X000 Coil former Sections 1 Insulating washer (reel packing, PU = 1 reel) Coil former AN 0,6 10,8 _ 0,15 FPK0269-6 Insulating washer 3.6 1.6±0.2 FPK0353-Q Please read Cautions and warnings and Important notes at the end of this document. ø11.1±0.2 ø22.3±0.2 ø12,8 _ 0,15 ø11,7+0,15 2,5+0,8 20,9 _ 0,2 3 09/06 P 26 × 16 Accessories Mounting assembly for printed circuit boards ■ The set comprises a terminal carrier and a yoke ■ For snap-in connection B65675 Terminal carrier Material: GFR polyterephthalate (UL 94 V-0, insulation class to IEC 60085: F max. operating temperature 155 °C), color code gray Pocan B4235 ® [E245249 (M)], LANXESS AG Solderability: to IEC 60068-2-20, test Ta, method 1 (aging 3): 235 °C, 2 s Resistance to soldering heat: to IEC 60068-2-20, test Tb, method 1B: 350 °C, 3.5 s Yoke Spring yoke, made of tinned nickel silver (0.4 mm), with ground terminal Complete mounting assembly (8 solder terminals) Ordering code: B65675B0005X000 Grounding pin This recess must be on the side of the grounding pin to ensure that the yoke locks into position. Hole arrangement View in mounting direction Ground a) Yoke b) Terminal carrier with 8 solder terminals Please read Cautions and warnings and Important notes at the end of this document. 4 09/06 P 26 × 16 Accessories Adjusting screw ■ Tube core with thread and core brake made of GFR polyterephthalate B65679 Pocan B3235 ® [E245249 (M)], LANXESS AG Tube core ∅ × length (mm) 4.55 × 6.3 4.98 × 6.3 Ordering code Material N22 N22 Color code red black B65679E0003X022 B65679E0002X022 Note: Due to the limited distance between adjusting screw and internal borehole, the entire assembly must be accurately centered. Please read Cautions and warnings and Important notes at the end of this document. 5 09/06 Ferrites and accessories Cautions and warnings Mechanical stress and mounting Ferrite cores have to meet mechanical requirements during assembling and for a growing number of applications. Since ferrites are ceramic materials one has to be aware of the special behavior under mechanical load. As valid for any ceramic material, ferrite cores are brittle and sensitive to any shock, fast changing or tensile load. Especially high cooling rates under ultrasonic cleaning and high static or cyclic loads can cause cracks or failure of the ferrite cores. For detailed information see Data Book 2007, chapter “General – Definitions, 8.1”. Effects of core combination on AL value Stresses in the core affect not only the mechanical but also the magnetic properties. It is apparent that the initial permeability is dependent on the stress state of the core. The higher the stresses are in the core, the lower is the value for the initial permeability. Thus the embedding medium should have the greatest possible elasticity. For detailed information see Data Book 2007, chapter “General – Definitions, 8.2”. Heating up Ferrites can run hot during operation at higher flux densities and higher frequencies. NiZn-materials The magnetic properties of NiZn-materials can change irreversible in high magnetic fields. Processing notes – The start of the winding process should be soft. Else the flanges may be destroid. – To strong winding forces may blast the flanges or squeeze the tube that the cores can no more be mount. – To long soldering time at high temperature (>300 °C) may effect coplanarity or pin arrangement. – Not following the processing notes for soldering of the J-leg terminals may cause solderability problems at the transformer because of pollution with Sn oxyd of the tin bath or burned insulation of the wire. For detailed information see Data Book 2007, chapter “Processing notes, 2.2”. – The dimensions of the hole arrangement have fixed values and should be understood as a recommendation for drilling the printed circuit board. For dimensioning the pins, the group of holes can only be seen under certain conditions, as they fit into the given hole arrangement. To avoid problems when mounting the transformer, the manufacturing tolerances for positioning the customers’ drilling process must be considered by increasing the hole diameter. 6 09/06 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of passive electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of a passive electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of a passive electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as “hazardous”). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, EPCOS-JONES, Baoke, Alu-X, CeraDiode, CSSP, MLSC, PhaseCap, PhaseMod, SIFI, SIFERRIT, SIKOREL, SilverCap, SIMID, SIOV, SIP5D, SIP5K, UltraCap, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. 7 09/06