UB084S01

UNIPAC OPTOELECTRONICS CORPORATION Spec. No. 413-212-061 Version : 3 Total pages : 14 Date : 2001 .01 .08 UB084S01 COLOR TFT-LCD MODULE SPECIFICATION MODEL NAME: UB084S01 The content of this technical information is subject to change without notice. Please contact Unipac or its agent for further information. Unipac copyright 2001 All rights reserved, Copying forbidden. Record of Revision Version 1 2 Revise Date 26/Jun./2000 22/Sep./2000 5 Page First draft. 3.a. Change current consumption of power supply voltage => IA=310 ¡ Content 220(Typ.) 300(Max.) => IB=330 7 8 c.(1). Change DE mode ¡ e. Change VL=> - Change PL=> (2.3) ¡ Change VS=> 750 £ (910) (Typ.) T=0 (700) (Typ.) T= 25 50(Min.) ¢ 550 £ Change FL=> £ 9 80(Max.) 250(Typ.) & add Note 3 £ C. Change CR=>200 Change Brightness=> 150(Typ.) Remark: note 3,6,7 90(Typ.) Remark:note 3,6,8 £ Change remark of viewing angle=>note 8 Add remark of color chromaticity=> note 3 Change remark of white uniformity=> note 9 12 13 14 3 08/Jan./2001 8 Change packing form Change outline dimension drawing Change timing chart £ £ Lamp starting voltage Vs=> (910)(Typ.) (700)(Typ.) 9 Brightness YL =>Add 2 mA lamp current spec. (50 nit) Color chromaticity=> ¤ ¥ ¤ £ Wx : 0.31 .0.31 0.03 ; Wy : 0.33 £ ¢ ¡ ¡ Change IL=> - ¡ - 539(Max.) 3(Min.) 2.25(Typ.) ¡   441(Min.) 490(Typ.) (505) note 3,9 note 10 910(Max.) T=0° C 700(Max.) T=25° C .0.33 0.03 Record of Revision Version Revise Date Page § ¦ Content § § ¦ ¦ Rx : 0.57 .0.57 ¦ 0.03 0.03 § ; ; ; Ry : 0.32 .0.32 0.03 0.03 0.03 Gx : 0.30 ¦ .0.30 § Gy : 0.56 ¦ .0.56 § Bx : 0.15 10 12 14 Add Note 9 .0.15 0.03 By : 0.12 .0.12 Add the position of carton label Detail DE timing: Tv Th ¦ A. Physical specification ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ B. Electrical specifications ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ Contents: 1. Pin assignment ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ 2. Absolute maximum ratings ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ 3. Electrical characteristics ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ a. Typical operating conditions ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ b. Display color v. s. input data signals PAGE S PEC NO. : 4 13-212-061 … ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ c. Input signal timing ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ d. Display position ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ e. B acklight driving conditions ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ C. Optical specifications ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ D. Reliability test items ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ E. Display quality ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ F. Handling precaution ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ G. Packing form ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ Appendix: ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP. Fig.1 LCM outline dimensions ……… ¨ ……… ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ Fig.2 Timing chart ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ ¨ : 1 /14 P14 P13 P12 P11 P11 P11 P9 P8 P7 P7 P6 P5 P5 P4 P3 P3 P2 S PEC NO. : 4 13-212-061 PAGE : 2 /14 A. Physical specifications NO. 1 2 3 4 5 6 7 Item © Specification 800 (H) 600 (V) 127.8 (V) © Remark Display resolution(pixel) Active area(mm) Screen size(inch) Pixel pitch(mm) Color configuration Overall dimension(mm) Weight(g) 170.4 (H) 8.4 (Diagonal) © © 0.213 (H) 0.213 (V) R. G. B. Vertical stripe © 203.0 (W)  142.5 (H) 5.7(D) Note 1 230 10 Note 1: Refer to Fig. 1. A LL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP. S PEC NO. : 4 13-212-061 : PAGE 3 /14 B. Electrical specifications B. Electrical specifications 1.Pin assignment (1).Input signal interface Pin no 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Symbol VCC VCC GND GND RxIN0RxIN0+ GND RxIN1RxIN1+ GND RxIN2RxIN2+ GND CKINCKIN+ GND NC NC GND GND Ground Ground Ground Ground Function +3.3 V power supply +3.3 V power supply Ground Ground LVDS receiver signal channel 0 Etc. LVDS receiver signal channel 1 LVDS receiver signal channel 2 LVDS receiver signal clock No Connection No Connection Ground Ground CN1 (20P) connector: HRS DF 19K-20P-1H or compatible ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP. S PEC NO. : 4 13-212-061 PAGE (2) LVDS transmitter/receiver signal mapping Symbol TxIN0 TxIN1 TxIN2 TxIN3 TxIN4 TxIN5 TxIN6 TxIN7 TxIN8 TxIN9 TxIN10 TxIN11 TxIN12 TxIN13 TxIN14 TxIN15 TxIN16 TxIN17 TxIN18 TxIN19 TxIN20 TxCLKIN R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5 Hs Vs DE CLK Red data (LSB) Red data Red data Red data Red data Red data (MSB) Green data (LSB) Green data Green data Green data Green data Green data (MSB) Blue data (LSB) Blue data Blue data Blue data Blue data Blue data (MSB) Horizontal sync Vertical sync Data enable Clock Dot clock 6 bits blue display data 6 bit green display data 6 bit red display data Function : 4 /14 2. Absolute maximum ratings Parameter Power voltage Input signal voltage Operating temperature Storage temperature Symbol VCC VLH Top TST  (GND = 0 V) Values Min. -0.3 -0.3 0 -20 Max. 4 VCC+0.3 +60  Unit VDC VDC  Remark At 25  At 25 Note 1 Note 1  +70 Note 1:The relative humidity must not exceed 90% non-condensing at temperatures of 40 or less. At temperatures greater than 40 , the wet bulb temperature must not exceed 39 . When operate at low temperatures, the brightness of CCFL will drop and the lifetime of CCFL will be reduced. Note 2:The unit should not be exposed to corrosive chemicals.  ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP.  S PEC NO. : 4 13-212-061 PAGE 3. Electrical characteristics a. Typical operating conditions Item Power supply voltage Input voltage Current consumption Inrush current Internal logic Low voltage High voltage Power ripple voltage Symbol VCC IA IB I RUSH VIL VIH VRP Min. 3.0 0 0.7VCC  : 5 /14 Typ. 3.3 220 - Max. 3.6 300 1500 0.3 VCC VCC 100 Unit V mArms mArms mApeak Remark Note 1 Note 2 mVp-p Note 1:Effective value (mArms) at VCC = 3.3 V/25 . IA IB Black (0) 64 Gray (7) 64 Vertical stripe line White 64 Grayscale Black Note 2: Refer to the following power-on condition. 90% Vcc 10%  Ton=470 s 10% Sequence of power-on/off and signal-on/off T3 T4 0ms T1 70msec T1 T5 T2   0 T2 70msec T3  300msec  Input signal 300msec  T5 10msec Apply the lamp voltage within the LCD operating range. When the backlight turns on before the LCD operation or the LCD turns off before the backlight turns off, the display may momentarily become abnormal. ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP.   Power  T4 S PEC NO. : 4 13-212-061 PAGE : 6 /14 Caution The above on/off sequence should be applied to avoid abnormal function in the display. In case of handling: Make sure to turn off the power when you plug the cable into the input connector or pull the cable out of the connector. b. Display color vs. input data signals Display colors Black Blue Red Magenta Green Cyan Yellow White Black Dark Red grayscale  Data signal (0 : Low level, 1: High level) R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 1 0 0 1 1 0 0 1 1 0 1 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 Basic colors Bright 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Red Black Dark Green grayscale Bright ! Green Black Dark Blue grayscale Bright ! 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 Blue 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 0 1 Note: Each basic color can be displayed in 64 gray scales using the 6 bit data signals. By combining the 18-bit data signals(R, G, B), the 262, 144 colors can be achieved on the display. ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP. S PEC NO. : 4 13-212-061 PAGE c. Input signal timing Timing diagrams of input signal are shown in Fig 2. (1). Timing characteristics of input signals DE mode Item Clock frequency Horizontal blanking Horizontal display period Horizontal sync. period Vertical blanking Vertical display width Vertical sync. period Symbol Fck Thb1 Thd Th Tvb1 Tvd Tv Min. 38 235 1035 10 610 Typ. 40 256 800 1056 28 600 628 Max. 42 500 1300 150 750 Unit MHz Clk Clk Clk Th Th Th Remark : 7 /14 (2). The timing condition of LVDS Item The differential level The common mode input voltage The input setup time The input hold time " Symbol " Min. 0.1 VID 2 0.5 0.5 $ $ Typ. # Max. 0.6 2.4 VID 2 $ $ Unit V V ns ns VID VIC tsu1 th1 VID VID = VIAP - VIAM VIAP VIAM tsu1 th1 An 7 LCK d. Display position D( 1,1 ) D( 1,2 ) . . . D( 1,Y ) . . . D( 1,599 ) D( 1,600 ) D( 2,1 ) D( 2,2 ) …… …… …… D( 2,Y ) …… …… D( 2,599 ) D( 2,600 ) …… …… D( X,1 ) D( X,2 ) . . . D( X,Y ) . . . D( X,599 ) D( X,600 ) …… …… …… …… …… …… …… D( 799,1 ) D( 799,2 ) . . . D( 799,Y ) . . . D( 800,1 ) D( 800,2 ) . . . D( 800,Y ) . . . % D( 799,599) D( 800,599 ) D( 799,600) D( 800,600) ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP. S PEC NO. : 4 13-212-061 PAGE e. Backlight driving conditions Parameter Lamp voltage Lamp current Power consumption Lamp starting voltage Frequency Lamp life time & : 8 /14 Symbol VL IL PL VS FL LL Min. 441 3 50 10000 Typ. 490 4.6 2.25 60 20000 Max. 539 910 700 80 - Unit Vrms mArms W Vrms KHZ Hr Remark Note 1 Note 1 Note 2 & & T=0 T=25 Note 3 Note 1, 4 Note 1: T= 25 Note 2: Inverter should be designed with the characteristic of lamp. When you are designing the inverter, the output voltage of the inverter should comply with the following conditions. (1). The area under the positive and negative cycles of the waveform of the lamp current and lamp voltage should be area symmetric(the symmetric ratio should be larger than 90%). (2). There should not be any spikes in the waveform. (3). The waveform should be sine wave as possible. (4). Lamp current should not exceed the maximum value within the operating temperature (It is prohibited to over the maximum lamp current even if operated in the non-guaranteed temperature). When lamp current over the maximum value for a long time, it may cause fire. Therefore, it is recommend that the inverter should have the current limit circuit. Note 3: Lamp frequency may produce interference with horizontal synchronous frequency and this may cause line flow on the display. Therefore lamp frequency shall be detached from the horizontal synchronous frequency and its harmonics as far as possible in order to avoid interference. In case using the inverter by PWM control, PWM frequency may interference with frame frequency. We suggest that PWM frequency is same as frame frequency. Note 4: Brightness to be decrease to the 50% of the initial value. Note 5: CN2 connector (backlight): BHSR-02VS-1(JST) Mating connector: SM02B-BHSS-1-TB (JST) Pin no. 1 2 Symbol H L Function CCFL power supply(H.V.) CCFL power supply(GND) Remark Cable color: Pink Cable color: White ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP. S PEC NO. : 4 13-212-061 PAGE : 9 /14 C. Optical specifications ( Note 1, Note 2 ) Item Response time Rising time Falling time Contrast ratio Viewing angle Top Bottom Left Right CR 0 Symbol Condition Specification Min. Typ. 20 30 250 150 90 50 0.31 0.33 0.57 0.32 0.30 0.56 0.15 0.12 Max. 40 50 0.34 0.36 0.60 0.35 0.33 0.59 0.18 0.15 1.8 Unit Remark Rx Ry Gx Gy Bx By 3 White uniformity W 4 Note 1: Ambient temperature = 25 . Note 2: To be measured in dark room after lighting the backlight for 30 minutes. Note 3: To be measured with the viewing cone of 1 by Topcon luminance meter BM-5A. Note 4: Definition of response time: The output signals of BM-7 are measured when the input signals are changed from “Black” to “White” (falling time) and from “White” to “Black” (rising time), respectively. The response time interval between the 10% and 90% of amplitudes. Refer to figure as below. 5 "White" 100% 90% 10% 0% Tr ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP. 1 Wy 2 Color chromaticity(CIE) Wx =0 2 1 Brightness YL =0 ( ) CR =0 ( ' Tr Tf =0 ms Note 4 Note 3, 5 150 30 10 40 40 0.28 0.30 0.54 0.29 0.27 0.53 0.12 0.09 - 10 deg. Note 3,10 nit nit nit Note 3,6,7 Note 3,6,8 Note 3,6,9 Note 3 Note 3,11 "Black" "White" Signal(Relative value) Tf S PEC NO. : 4 13-212-061 PAGE Note 5. Definition of contrast ratio: Contrast ratio is calculated with the following formula. Contrast ratio (CR)= Brightness on the “white” state Brightness on the “black” state : 1 0/14 Note 6: Definition of brightness: This shall be measured at center of the screen. Note 7: Driving conditions for CCFL : IL=4.6 mA,60KHz frequency Note 8: Driving condition for CCFL : IL=3 mA,60KHz frequency Note 9: Driving condition for CCFL : IL=2 mA,60KHz frequency Note 10: Definition of viewing angle: Note 11: Definition of white uniformity: White uniformity is defined as the following with thirteen measurements (1~9). W = Maximum brightness of nine points Minimum brightness of nine points ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP. 6 7 S PEC NO. : 4 13-212-061 PAGE : 11/14 D. Reliability test items (Note 1) 8 8 8 8 8 Test tem High temperature storage 70 Test Condition , 240Hrs Remark Note 1, 2, 3 Low temperature storage -20 , 240Hrs Note 1, 2, 3 High temperature & high humidity operation 40 , 90%RH, 240Hrs Note 1, 2, 3 (No condensation) High temperature operation 60 , 240Hrs Note 1, 2, 3 1H, 10mins, 1H, 5cycles 150 pF,150 ,10kV,1 second, 9 position Note 3 on the panel, 10 times each place Sweep:1G, 10HZ ~ 500HZ ~ 10HZ /2.5min Note 1, 2, 3 2 hour for each direction X, Y, Z (6 Hrs in total) @ @ @ 9 Electrostatic discharge (non-operation) Vibration (non-operation) Mechanical shock (non-operation) 50G/11ms, 200G/2ms, once for each direction Note 1: Evaluation should be tested after storage at room temperature for one hour. Note 2: There should be no change which might affect the practical display function when the display quality test is conducted under normal operating condition. Note 3: Judgement : 1.Function OK. 2.No serious image quality degradation . E. D isplay quality The display quality of the color TFT-LCD module should be in compliance with the Unipac ’ s OQC inspection standard. F. H andling precaution The Handling of the TFT-LCD should be in compliance with the Unipac’s handling principle standard. ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP. 8 Temperature cycling (non-operation) -20 8 Low temperature operation 0 , 240Hrs Note 1, 2, 3 ~70 Note 1, 2, 3 X, Y, Z Note 1, 2, 3 S PEC NO. : 4 13-212-061 PAGE : 1 2/14 G. Packing f orm : LCD Module Anti-Static Bag NOTE : 1. Max. Capacity : 30 LCD Modules/Carton. 2. Max. Weight : 10 Kg/Carton. 3. Meas : 600 mm*353mm*210mm. EPP Cushion Carton ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP. S PEC NO. : 4 13-212-061 PAGE : 1 3/14 ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP. Fig.1 LCM outline dimensions S PEC NO. : 4 13-212-061 PAGE : 1 4/14 Invalid X,599 X,600 Tvd 799,Y 800,Y invalid Thd (1 pixel / clock) Invalid Tvbl X,599 X,600 Fck CLK RGB RGB DE 800,Y invalid Thbl ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM UNIPAC OPTOELECTRONICS CORP. DE Fig.2 Timing chart X,1 X,2 X,3 3,Y 1,Y 2,Y Th Tv UNIPAC OPTOELECTRONICS CORPORATION TERMS AND CONDITIONS OF SALE These Terms and Conditions of Sale apply to all items designed and/or made by Unipac Optoelectronics Corporation ("Unipac"), and Buyer agrees they apply to all such items. 1 ACCEPTANCE OF TERMS. BUYER ACCEPTS THESE TERMS (i) BY WRITTEN ACCEPTANCE (BY PURCHASE ORDER OR OTHERWISE), OR (ii) BY FAILURE TO RETURN GOODS SUPPLIED BY UNIPAC WITHIN 5 DAYS OF THEIR DELIVERY. 2 DELIVERY 2.1 Delivery will be made Free Carrier (Incoterms 1990), Unipac's warehouse, Science-Based Industrial Park, Taiwan to a carrier designated in writing by Buyer, or if Buyer fails to designate a carrier, to a carrier designated by Unipac. 2.2 Title to the goods and the entire risk will pass to Buyer upon delivery to carrier. 2.3 Shipments are subject to availability. Unipac shall make every reasonable effort to meet the date(s) quoted or acknowledged; and if Unipac makes such effort, UNIPAC WILL NOT BE LIABLE FOR ANY DELAYS. 3 TERMS OF PAYMENT 3.1 Unless otherwise stated on Unipac's quotation, all shipments shall be T/T in advance, by Letter of Credit at Sight, or pursuant to agreed prepayment terms. Unipac reserves the right to change credit terms at any time in its sole discretion. 3.2 Buyer guarantees prompt payment of all obligations accrued pursuant to purchase orders issued by Buyer. 4 LIMITED WARRANTY 4.1 Unipac warrants that the goods sold will be free from defects in material and workmanship and comply with Unipac's applicable published specifications for a period of sixty (60) days from the date of Unipac's shipment. 4.2 Goods or parts which have been subject to abuse (including without limitation repeated or extended exposure to conditions at or near the limits of applicable absolute ratings) misuse, accident, alteration, neglect, or unauthorized repair or improper application are not covered by any warranty. No warranty is made with respect to custom products or goods produced to Buyer's specifications (unless specifically stated in writing signed by Unipac). Unipac shall not be responsible for defects or claims caused by acts not performed by Unipac; or by combination of goods with other things. 4.3 No warranty is made with respect to goods used in devices intended for use in applications where failure to perform when properly used can reasonably be expected to result in significant injury (including, without limitation, navigation, aviation, weaponry or nuclear equipment, or for surgical implant or to support or sustain life) and Buyer agrees to indemnify, defend, and hold harmless Unipac from all claims, damages and liabilities arising out of any such uses. 4.4 This Article 4 is the only warranty by Unipac with respect to goods and may not be modified or amended except in writing signed by an authorized officer of Unipac. 4.5 Buyer acknowledges and agrees that it is not relying on any applications, diagrams or circuits contained in any literature, and Buyer will test all parts and applications under extended field and laboratory conditions. Notwithstanding any crossreference or any statements of compatibility, functionality, interchangeability, and the like, the goods may differ from similar goods from other vendors in performance, function or operation, and in areas not contained in the written specifications, or as to ranges and conditions outside such specifications; and Buyer agrees that there are no warranties and that Unipac is not responsible for such things. 4.6 REGARDLESS OF CAUSE OR REASON FOR DAMAGE (WHETHER ACCIDENT, NEGLIGENCE, OR OTHERWISE) UNIPAC SHALL HAVE NO LIABILITY (DIRECT, CONSEQUENTIAL OR OTHER) FOR, IN CONNECTION WITH OR ARISING FROM PROPERTY FURNISHED FOR USE AT OR LEFT AT UNIPAC; and by delivering or entrusting property to Unipac, Buyer expressly confirms this limitation. Notwithstanding this limitation, Unipac will replace, or pay the reasonable retooling costs to replace, masks damaged or destroyed as a result of Unipac's gross negligence or fault. 4.7 EXCEPT AS PROVIDED ABOVE, UNIPAC MAKES NO WARRANTIES OR CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY; AND UNIPAC EXPRESSLY EXCLUDES AND DISCLAIMS ANY WARRANTY OR CONDITION OF NONINFRINGEMENT, MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE OR APPLICATION. THIS AGREEMENTSTATES THE ONLY AND EXCLUSIVE REMEDY FOR ANY AND ALL CLAIMS MADE AGAINST UNIPAC UNDER ANY AGREEMENT AND/OR WITH RESPECT TO PANELS, COMPONENTS, SERVICES AND/OR GOODS. 5.5 No action or proceeding may be commenced by either party against the other (other than to collect money due for goods delivered or services rendered), whether for breach, indemnification, contribution or otherwise, more than one year after delivery of the goods to the carrier; and no claim may be brought unless the non-claiming party has first been given commercially reasonable notice, a full written explanation of all pertinent details (including copies of all materials), and a good faith opportunity to resolve the matter. 5.6 BUYER EXPRESSLY AGREES TO THE LIMITATIONS OF ARTICLES 5, 8 AND 9 AND TO THEIR REASONABLENESS. 5.7 The exclusions and limitations of Articles 5, 8 and 9 will survive the termination of the applicable Agreements, and shall apply notwithstanding any claim of a failure of any one or more remedies to accomplish their purpose, and THE PARTIES EXPRESSLY WAIVE AND RELINQUISH ANY CONTRARY RIGHTS UNDER ANY AGREEMENT, AND/OR LAW, DECISION, CUSTOM OR PRACTICE. 6 SUBSTITUTIONS AND MODIFICATIONS Unipac may at any time make substitutions for product ordered which do not materially and adversely affect overall performance with the then current specifications in the typical and intended use. Unipac reserves the right to halt deliveries and shipments and alter specifications and prices without notice. Buyer shall verify that the literature and information is current before purchasing. Other changes to process and/or specifications by Unipac shall be pursuant to Unipac’ s standard ECN procedures. 7 CANCELLATION 7.1 This Agreement may not be canceled by Buyer except with written consent by Unipac and Buyer's payment of reasonable cancellation charges (including but not be limited to expenses already incurred for labor and material, overhead, commitments made by Unipac, and a reasonable profit). 7.2 8 In no event will Buyer have rights in partially completed goods. INDEMNIFICATION 8.1 Unipac will, at its own expense, assist Buyer with technical support and information in connection with any claim that any parts as shipped by Unipac under this purchase order infringe any valid, enforceable, unexpired R.O.C. patent, copyright, or trademark, provided however, that Buyer (i) gives immediate written notice to Unipac, (ii) permits Unipac to participate and to defend if Unipac requests to do so, and (iii) gives Unipac all needed information, assistance and authority. However, Unipac will not be responsible for infringements resulting from anything not entirely manufactured by Unipac, or from any combination with products, equipment, or materials not furnished by Unipac. Unipac will have no liability with respect to intellectual property matters arising out of products made to Buyer's specifications, code, or designs. 8.2 Except as expressly stated in this Article 8 or in another writing signed by an authorized officer, Unipac makes no representations and/or warranties with respect to intellectual and/or industrial property and/or with respect to claims of infringement. 8.3 Except as to claims Unipac agrees in writing to defend, BUYER WILL INDEMNIFY, DEFEND AND HOLD HARMLESS UNIPAC FROM ALL CLAIMS, COSTS, LOSSES, AND DAMAGES (INCLUDING ATTORNEYS FEES) AGAINST AND/OR ARISING OUT OF GOODS SOLD AND/OR SHIPPED HEREUNDER. 9 NO CONFIDENTIAL INFORMATION Unipac shall have no obligation to hold any information in confidence except as provided in a separate non-disclosure agreement signed by both parties. 10 ENTIRE AGREEMENT These terms and conditions are the entire agreement between Unipac and Buyer, and no addition, deletion or modification shall be binding on Unipac unless expressly agreed to in a writing signed by an officer of Unipac. Buyer is not relying upon any warranty or representation except for those specifically stated here. 11 APPLICABLE LAW This Agreement and all performance and disputes arising out of or relating to goods involved will be governed by the laws of Taiwan, Republic of China, without reference to conflict of laws principles and excluding the U.N. Convention on Contracts for the 5 LIMITATION OF LIABILITY International Sale of Goods. Buyer agrees at its sole expense to comply with all applicable laws in connection with the purchase, use or sale of the goods provided 5.1 Unipac will not be liable for any loss, damage or penalty resulting from causes beyond its reasonable control, including but not limited to delay by others, force majeure, hereunder. acts of God, material shortage or labor conditions. In any such event, the date(s) for 12 DISPUTE RESOLUTION Unipac's performance will be deemed extended for a period equal to any delay resulting. 12.1 Buyer and Unipac shall cooperate and attempt in good faith to resolve any and all 5.2 THE LIABILITY OF UNIPAC ARISING OUT OF THIS AGREEMENT OR ANY disputes arising out of and/or relating to this Agreement and/or goods furnished GOODS SOLD WILL BE LIMITED TO REFUND OF THE PURCHASE PRICE OR pursuant to this Agreement. (WITH UNIPAC'S PRIOR WRITTEN CONSENT) REPAIR OR REPLACEMENT OF 12.2 Any disputes relating to and/or arising out of any Agreement and/or goods PURCHASED GOODS (RETURNED TO UNIPAC FREIGHT PRE-PAID); OR IN THE furnished pursuant to this Agreement that cannot be so resolved will be decided EVENT OF A FAILURE OR BREACH BY UNIPAC REGARDING DELIVERY, AN exclusively by binding arbitration. Such arbitration shall take place in Taipei, Taiwan AMOUNT EQUAL TO THE TOTAL PURCHASE PRICE OF THE GOODS THAT HAVE pursuant to the Rules for International Arbitrations under the American Arbitration NOT BEEN DELIVERED DUE TO SUCH FAILURE. Association. 5.3 Buyer will not return any goods without first obtaining a customer return order 12.3 Notwithstanding anything to the contrary, any party may apply to any court of number. competent jurisdiction for interim injunctive relief with respect to irreparable harm which 5.4 AS A SEPARATE LIMITATION, IN NO EVENT WILL UNIPAC BE LIABLE (i) FOR cannot be avoided and/or compensated by such arbitration proceedings, without breach COSTS OF SUBSTITUTE GOODS, (ii) FOR ANY SPECIAL, CONSEQUENTIAL, of this Article 12 and without any abridgment of the powers of the arbitrators. INCIDENTAL, RELIANCE OR INDIRECT DAMAGES, OR (iii) FOR LOSS OF USE, 13 ATTORNEYS' FEES OPPORTUNITY, MARKET POTENTIAL, GOODWILL AND/OR PROFIT ON ANY Reasonable attorneys' fees and costs will be awarded to the prevailing party in the THEORY (CONTRACT, TORT, FROM THIRD PARTY CLAIMS OR OTHERWISE). event of litigation involving the enforcement or interpretation of this Agreement. THESE LIMITATIONS SHALL APPLY NOTWITHSTANDING ANY FAILURE OF ESSENTIAL PURPOSE OR OF ANY FAILURE OR INADEQUACY OF ANY REMEDY. Unipac Optoelectronics Corp. No.5, Li-Hsin Road 6 , Science-Based Industrial Park, Hsin-Chu City, Taiwan, R.O.C. Fax:886-3-5772545 Tel :886-3-5632899 Unipac copyright 2001 All rights reserved , copying forbidden.