P0583

THT CURRENT SENSE TRANSFORMERS UL/C-UL recognized components 3000Vrms gate to drive winding test Useful operating frequency from 50kHz to 500kHz Most popular winding configurations Electrical Specifications @ 25°C — Operating Temperature -40°C to 130°C Part Number P0581 P0582 P0583 6 Turns Ratio 200:1:1 100:1:1 50:1:1 Primary Inductance (1-10) (mH MIN) 76 19 5 DCR Pri (1-10) (Ω MAX) 2.8 1.4 0.7 DCR Sec1 (3-7) (mΩ ±15%) 1.7 1.7 1.7 DCR Sec2 (4-8) (mΩ ±15%) 1.7 1.7 1.7 Hi-Pot (Pri-Sec) (Vrms) 3000 3000 3000 Additional Specifications Part Number P0581 P0582 P0583 RT 200 100 15 Reference Data Ipk Droop (Amps) (%) 34 1.00 35 1.98 36 1.19 Calculation Data Max Flux Density 2000 2000 2000 Kb 17.12 68.49 273.97 Req (mΩ) .9 .8 .75 NOTES: 1. These current sense transformers have two one turn primaries that can be used in parallel. The listed current ratings are for parallel connection. 2. The reference values are for an application using the termination resistor (Rt) and operating with unipolar waveform at 100kHz, 40% duty cycle. The estimated temperature rise is 55°C. 3. The peak flux density should remain below 2100 Gauss to ensure that the core does not saturate. Use the following formula to calculate the peak flux density: Bpk = Kb * Ipk * Rt * don/(Ff * Freq. in kHz) where: Rt is the terminating resistor in the application and Ff is 1 for unipolar waveform and 2 for bipolar waveform 4. To calculate the droop: Droop Exponent (D) = Rt * don/(Lpri in mH * Freq. in kHz) %Droop = (1-e-D) * 100 5. The temperature rise of the component is calculated based on the total core loss and copper loss: A. To calculate total copper loss (W): P(cu) = Ipk2 * Req * Ff * don where: Ff is 1 for unipolar waveform and 2 for bipolar waveform B. To calculate total core loss (W): P(core) = 0.000073 * (Freq. in kHz)1.67 * (Bop in kG)2.532 where: Bop in kG = Kb * Ipk * Rt * don/(2000 * Freq. in kHz) C. To calculate temperature rise: Temperature Rise (C) = 60.18 * (Core Loss(W) + Copper Loss (W)).833 6. To order RoHS compliant part, add the suffix "NL" to the part number (i.e. P0581 becomes P0581NL). Mechanical .810 MAX 20,57 .580 MAX 14,73 Schematic Pri Sec 3 50T, 100T, or 200T 1T .750 MAX 19,05 .130 3,30 P058X Date Code Country of Origin 1 10 1T 4 8 7 3 1 4 10 .350 8,89 .700 17,78 7 Weight . . . . . . . . . . . . . . . .5 grams Tray . . . . . . . . . . . . . . . . . . .20/tray (6X) .040 .200 5,08 4 10 8 7 1 For More Information: Pulse Worldwide Headquarters 12220 World Trade Drive San Diego, CA 92128 U.S.A. www.pulseeng.com TEL: 858 674 8100 FAX: 858 674 8262 SUGGESTED PCB HOLE PATTERN Dimensions: Inches mm Unless otherwise specified, all tolerances are ± .010 0,25 Pulse Northern Europe 3 Huxley Road Surrey Research Park Guildford, Surrey GU2 5RE United Kingdom TEL: 44 1483 401700 FAX: 44 1483 401701 Pulse Southern Europe Zone Industrielle F-39270 Orgelet France TEL: 33 3 84 35 04 04 FAX: 33 3 84 25 46 41 Pulse Pulse North China China Headquarters Room 1503 No. 1 Industrial District Changan, Dongguan China TEL: 86 769 85538070 FAX: 86 769 85538870 XinYin Building No. 888 YiShan Road Shanghai 200233 China TEL: 86 21 54643211/2 FAX: 86 21 54643210 Pulse South Asia 150 Kampong Ampat #07-01/02 KA Centre Singapore 368324 TEL: 65 6287 8998 FAX: 65 6280 0080 Pulse North Asia No. 26 Kao Ching Road Yang Mei Chen Taoyuan Hsien Taiwan, R. O. C. TEL: 886 3 4641811 FAX: 886 3 4641911 Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. © Copyright, 2006. Pulse Engineering, Inc. All rights reserved. www.pulseeng.com P516.B (3/06)