100A18W101MV4U

CAPACITOR ARRAYS Capacitor arrays combine separate multi-layer ceramic capacitors of the same value in a single passive component. The primary advantages of this device are a reduction in PCB space and placement time. The arrays are offered in three standard dielectrics and feature barrier terminations and tape & reel packaging. FEATURES • Multiple Caps in One Chip • Reduces Circuit Size • Easier Handling • Lower Placement Cost • Increased Throughput APPLICATIONS • Cellular / Pagers • Handheld Equipment • PCMCIA Cards • Camcorders • PC’s & Peripherals CAPACITANCE / VOLTAGE SELECTION CHIP SIZE A11 / 0405 RATED VOLTAGE 10 VDC 16 VDC 25 VDC 16 VDC 25 VDC 50 VDC 100 VDC 330 pF 10 pF 470 pF 220 pF NPO DIELECTRIC min. MAX. 10 pF 10 pF 10 pF 680 pF 680 pF 680 pF X7R DIELECTRIC min. MAX. 560 pF 560 pF 560 pF .033 µF .015 µF 6800 pF 220 pF .047 µF .033 µF .022 µF .047 µF .022 µF .010 µF 4700 pF .150 µF .068 µF .010 µF .220 µF .100 µF .047 µF Y5V DIELECTRIC min. MAX. A18 / 0612 Available capacitance values include the following significant R12 retma values and their multiples: 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 ( 1.0 = 1.0, 10, 100, 1000, etc.) Please contact the factory for size/voltage/value combinations not shown. HOW TO ORDER - CAPACITOR ARRAYS 160 VOLTAGE 100 = 10 V 160 = 16 V 250 = 25 V 500 = 50 V 101 = 100 V A11 CASE SIZE A11 = 0405 A18 = 0612 N DIELECTRIC N = NPO W = X7R Y = Y5V 100 CAPACITANCE 1st two digits are significant; third digit denotes number of zeros 10 = 1.0 pF 101 = 100 pF J TOLERANCE J = ± 5% K = ± 10% M = ± 20% Z = + 80 - 20% V TERMINATION V = Ni barrier w/ 100% Sn Plating MARKING 4 = Unmarked 4 E TAPE MODIFIER Code Type Reel E Embossed 7” U Embossed 13” Tape specifications conform to EIA RS481 P/N written: 160A11N100JV4E 12 www.johanson dielectrics.com CAPACITOR ARRAYS Mechanical Dimensions: Size A11 In L W T Bw Bl P C .040 ± .005 .055 ± .005 .030 max. .015 ± .004 .010 ± .004 .026 ± .005 .013 ± .004 (mm) (1.02±.13) (1.40±.13) (0.76 max.) (0.38±0.10) (0.25±0.10) (0.66±0.13) (0.33±0.10) Bl Center of Chip W P L T C Bw Bs T Bc Bs Bc C/L of Chip Mechanical Dimensions: Size A18 In L W T B Bo Bs Bc .126±.008 .063±.008 .059 max. .016±.004 .008 Typical .030 Typical .045±.004 (mm) (3.20±.02) (1.60±.02) (1.50 max.) (0.41±0.1) (0.20 TYP) (0.76 TYP) (1.14±0.1) B L W Bo Center of Chip Bc Bs Bc Bs T B L Solder Pad Dimensions: Size A11 a Inches (mm) .020 (0.51) b .030 (0.76) e d Solder Pad Dimensions: Size A18 d .013 (0.33) e .026 (0.66) Inches (mm) a .035 (0.89) b .065 (1.65) e c .060 (1.52) c .100 (2.54 ) d d .018 (0.46) e .030 W Bo (0.79) c c a b b a Dielectric specifications are listed on page 20. www.johanson dielectrics.com 13