M170EG01V9

M170EG01 V.9 Product Specification AU OPTRONICS CORPORATION Product Specification 17.0” SXGA Color TFT-LCD Module Model Name: M170EG01 V.9 Approved by Prepared by CC Chiu DDBU Marketing Division / AU Optronics corporation Customer Checked & Approved by ver0.1 1/25 M170EG01 V.9 Product Specification Product Specification 17.0” SXGA Color TFT-LCD Module Model Name: M170EG01 V.9 (u ) Preliminary Specifications ( ) Final Specifications Note: This Specification is subject to change without notice. ver0.1 3/25 M170EG01 V.9 Product Specification Contents 1.0 Handling Precautions.........................................................6 2.0 General Description ...........................................................7 2.1 Display Characteristics .................................................................................................................... 7 2.2 Optical Characteristics..................................................................................................................... 8 3.0 Functional Block Diagram ................................................11 4.0 Absolute Maximum Ratings..............................................12 4.1 TFT LCD Module ............................................................................................................................ 12 4.2 Backlight Unit .................................................................................................................................. 12 4.3 Absolute Ratings of Environment .................................................................................................. 12 5.0 Electrical characteristics ..................................................13 5.1 TFT LCD Module ............................................................................................................................ 13 5.1.1 Power Specification..........................................................................................................................13 5.1.2 Signal Electrical Characteristics........................................................................................................14 5.2 Backlight Unit .................................................................................................................................. 15 6.0 Signal Characteristic........................................................15 6.1 Pixel Format Image ........................................................................................................................ 15 6.2 The input data format...................................................................................................................... 16 6.3 Signal Description .......................................................................................................................... 17 6.4 Interface Timing ............................................................................................................................... 18 6.4.1 Timing Characteristics......................................................................................................................18 6.4.2 Timing diagram ................................................................................................................................19 6.5 Power ON/OFF Sequence ............................................................................................................ 20 7.0 Connector & Pin Assignment............................................21 7.1 TFT LCD Module ............................................................................................................................ 21 7.2 Backlight Unit .................................................................................................................................. 22 7.3 Signal for Lamp connector............................................................................................................. 22 8.0 Reliability ........................................................................23 9.0 Safety ..............................................................................24 9.1 Sharp Edge Requirements ............................................................................................................ 24 9.2 Materials .......................................................................................................................................... 24 9.2.1 Toxicity...........................................................................................................................................24 9.2.2 Flammability....................................................................................................................................24 9.3 Capacitors ....................................................................................................................................... 24 10.0 Other requirement .........................................................24 10.1 National Test Lab Requirement................................................................................................... 24 10.2 Label .............................................................................................................................................. 24 11.0 Mechanical Characteristics.............................................25 ver0.1 4/25 M170EG01 V.9 Product Specification Record of Revision Version and Date Page 0.1 2005/02/28 All Old description First Edition for Customer New Description Remark ver0.1 5/25 M170EG01 V.9 Product Specification 1.0 Handling Precautions 1) Since front polarizer is easily damaged, pay attention not to scratch it. 2) Be sure to turn off power supply when inserting or disconnecting from input connector. 3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots. 4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling. 7) Do not open nor modify the Module Assembly. 8) Do not press or pat the panel surface by fingers,hand or tooling. 9) Do not press the reflector sheet at the back of the module to any directions. 10) In case if a module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the CCFL reflector edge. Instead, press at the far ends of the CCFL reflector edge softly. Otherwise the TFT module may be damaged. 11) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface Connector of the TFT module. 12) After installation of the TFT module into an enclosure (Desktop monitor Bezel, for example), do not twist nor bend the TFT Module even momentary. At designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the TFT module from outside. Otherwise the TFT module may be damaged. ver0.1 6/25 M170EG01 V.9 Product Specification 2.0 General Description This specification applies to the 17.0 inch Color TFT/LCD Module M170EG01 V9. This module is designed for a display unit of personal computer. The display supports the SXGA (1280(H) x 1024(V)) screen format and 16.2M colors (RGB 6-bits + FRC data). All input signals are 2 Channel LVDS interface compatible. This module does not contain an inverter card for backlight. 2.1 Display Characteristics The following items are characteristics summary on the table under 25 ℃ condition: ITEMS Screen Diagonal Active Area Pixels H x V Pixel Pitch Pixel Arrangement Display Mode White Luminance Contrast Ratio Optical Rise Time/Fall Time Color Saturation Nominal Input Voltage VDD Power Consumption (VDD line + CCFL line) Weight Physical Size Unit [mm] [mm] [mm] SPECIFICATIONS 432(17.0") 337.920 (H) x 270.336(V) 1280(x3) x 1024 0.264 (per one triad) x 0.264 R.G.B. Vertical Stripe Normally White 420 (Typ) 500 : 1 (Typ) 8 (Typ) 72% NTSC +5.0 V 25.8 W(Typ) (PDD=6 W, PCFL=19.8 W @Lamp=7.5mA) 1900 (Typ) Min. Typ. Horizatal(H) 358 358.5 Vertical(V) 296 296.5 Depth(D) 16.5 17.0 Dual Channel LVDS 16.2M colors (RGB 6-bit + FRC data) 0 to +50 -20 to +60 Hard-coating (2H), Glare treatment [cd/m2] [msec] [Volt] [Watt] [Grams] [mm] (Note 1) Max. 359.0 297 17.5 Electrical Interface Support Color Temperature Range Operating Storage (Shipping) Surface Treatment [oC] [oC] Note 1 :System should be warmed up for at least one hour ver0.1 7/25 M170EG01 V.9 Product Specification 2.2 Optical Characteristics The optical characteristics are measured under stable conditions at 25℃ (Room Temperature): Item Unit Conditions Min. Typ. Max. Horizontal (Right) 60 70 CR = 10 (Left) 60 70 Vertical (Up) 60 70 CR = 10 (Down) 50 60 Viewing Angle [degree] Horizontal (Right) 70 80 CR = 5 (Left) 70 80 Vertical (Up) 70 80 CR = 5 (Down) 70 80 Contrast ratio Normal Direction Rising Time Response Time [msec] Falling Time Rising + Falling Red x Red y Color / Chromaticity Coordinates (CIE) Green x Green y Blue x Blue y Color White White Luminance @ CCFL 7.5mA (center) Luminance Uniformity Crosstalk (in 75Hz) Flicker Equipment [cd/m ] [%] [%] dB Pattern Generator, Power Supply, Digital Voltmeter, Luminance meter 2 Note - 300 0.61 0.31 0.26 0.58 0.11 0.04 0.28 0.30 336 75 500 6 2 8 0.64 0.34 0.29 0.61 0.14 0.07 0.31 0.33 420 80 1.5 -20 9 4 13 0.67 0.37 0.32 0.64 0.17 0.10 0.34 0.36 - Note 1 Coordinates (CIE) White x White y Note 2 Note 3 Note 4 (PR 880, BM-5A / BM7, CS-1000, CA210, SR_3, EZ Contrast*, Optiscope& Westar TRD-100) Aperture Test Point Environment 1°with 100cm VD or 2°with 50cm viewing distance Center (VESA point 9) < 1 lux Module Driving Equipment *’ EZ Contrast is different measurement tool with very close viewing distance. LCD Module measuring distance PR-880 / BM5A / BM7 ver0.1 8/25 M170EG01 V.9 Product Specification Note 1: Definition of Response time The output signals of photodetector are measured when the input signals are changed from “ Full Black” to “ Full White” (rising time), and from “ Full White” to “ Full Black ”(falling time), respectively. The response time is interval between the 10% and 90% of amplitudes. % Tr F Tr R 1 00 90 Optical response 10 0 White B lack White Note 2: Brightness uniformity of these 9 points is defined as below 90 % 50 % 10 % 10 % 50 % 90 % Uniformity = Minimum Luminance in 9 points (1 - 9) Maximum Luminance in 9 Points (1 - 9) ver0.1 9/25 M170EG01 V.9 Product Specification Note 3: Crosstalk is defined as below : 1/ 2 1/6 1/6 2/3 1/2 1/3 1/6 A A’ 1/6 1/3 1/2 B’ 2/3 1/2 B 184 gray level 184 gray level Unit: percentage of dimension of display area 0 gray level l LA-LA’ l / LA x 100%= 1.5% max., LA and LB are brightness at location A and B l LB-LB’ l / LB x 100%= 1.5% max., LA’ and LB’ are brightness at location A’ and B’ Note 4: Test Paterm: Subchecker Pattern RGBR GB Gray Level = L127 RGBR GB Gray Level = L0 RGBR GB Method: Record dBV & DC value with (WESTAR)TRD-100 Amplitude AC DC Time Flicker (dB) = 20 log AC Level(at 30 Hz) DC Level ver0.1 10/25 M170EG01 V.9 Product Specification 3.0 Functional Block Diagram The following diagram shows the functional block of the 19.0 inches wide Color TFT/LCD Module: AU ASIC Timing Controller G1 Y-Driver IC LVDS LVDS Receiver RSDS Transmitte rr TFT-LCD 1280*(3)*1024 Pixels X-Driver IC Connector + 5V G1024 D1 D3840 4 CCFL DC/DC Converter G amma Correction DC POWER Inverter AL2307-A0G1D-P / FI-XB30SSRL-HF16 Mating Type : JAE FI-X30HL JST-BHSR-02VS-1 ( 2pin ×2 ) SM02B-BHSS-1-TB ver0.1 11/25 M170EG01 V.9 Product Specification 4.0 Absolute Maximum Ratings Absolute maximum ratings of the module is as following: 4.1 TFT LCD Module Item Logic/LCD Drive Voltage Symbol VIN Min -0.3 Max +6 Unit [Volt] Conditions Note 1,2 4.2 Backlight Unit Item CCFL Current Symbol ICFL Min Max 8.5 Unit [mA] rms Conditions Note 1,2 4.3 Absolute Ratings of Environment Item Operating Temperature Operating Humidity Storage Temperature Storage Humidity Symbol TOP HOP TST HST Min 0 5 -20 5 Max +50 90 +60 90 Unit [ C] [%RH] [ C] [%RH] o o Conditions Note 3 Note 3 Note 3 Note 3 P lease refer the graph below for corresponding of Min/Max values of temperature and humidity. Note 1: With in Ta (25℃ ) Note 2: Permanent damage to the device may occur if exceed maximum values Note 3: For quality perfermance, please refer to AUO IIS(Incoming Inspection Standard). ver0.1 12/25 M170EG01 V.9 Product Specification 5.0 Electrical characteristics 5.1 TFT LCD Module 5.1.1 Power Specification Input power specifications are as follows; Symbol VDD IDD Irush PDD VDDrp P arameter Logic/LCD Drive Voltage VDD current LCD Inrush Current VDD Power Allowable Logic/LCD Drive Ripple Voltage Min 4.5 Typ 5 1200 6 M ax 5.5 1560 2.5 7.8 100 Units [Volt] [mA] [A] [Watt] [mV] p-p ± 10% Vin=5V , All Black Pattern, at 75Hz Note Vin=5V , All Black Pattern, at 75Hz Vin=5V , All Black Pattern, at 75Hz Condition Note: Measurement conditions: +5.0V D6 D5 D2 D1 R1 47K Q3 AO6402 F1 S VCC G (LCD Module Input) C1 1uF/16V (High to Low) Control Signal SW D1 D2 D5 D6 R2 G 1K C3 +12.0V VR1 47K 0.01uF/25V S Q3 AO6402 C2 1uF/25V 90% 5. 0V 10% 0V 470 us Vin rising time ver0.1 13/25 M170EG01 V.9 Product Specification 5.1.2 Signal Electrical Characteristics Input signals shall be low or Hi-Z state when Vin is off It is recommended to refer the specifications of SN75LVDS82DGG (Texas Instruments) in detail. Each signal characteristics are as follows; Symbol VTH VTL ¦ VID¦ VICM P arameter Differential Input High Threshold Differential Input Low Threshold Input Differential Voltage Differential Input Common Mode Voltage Min -100 100 1.1 Typ 400 M ax 100 600 1.45 Units [mV] [mV] [mV] [V] VTH/VTL = ±100mV Condition VICM = 1.2V VICM = 1.2V Note Note Note Note Note: LVDS Signal Waveform VTH │VID│ VTL VICM VSS ver0.1 14/25 M170EG01 V.9 Product Specification 5.2 Backlight Unit Parameter guideline for CCFL Inverter Symbol ISCFL P arameter CCFL standard current Min. 7.0 Typ. 7.5 M ax. 8.0 Unit [mA] rms IRCFL FCFL ViCFL (0 C) ViCF (25 C) VCFL (for reference) CCFL Power consumption PCFL (for reference) LTCFL CCFL life Time 30,000 50,000 Note 1: CCFL standard current is measured at 25± ℃. 2 [Hour] (Ta=25oC) Note 4 19.8 21.8 [Watt] o o Condition (Ta=25oC) Note 1 CCFL operation range CCFL Frequency CCFL Ignition Voltage 3.0 40 7.5 60 8.0 80 [mA] rms [KHz] [Volt] (Ta=25oC) (Ta=25oC) Note 2 (Ta=0oC) 1500 (End of the lamp wire connector) CCFL Ignition Voltage 1150 (End of the lamp wire connector) CCFL Operation Voltage - - rms [Volt] 660 @7.5mA rms 700 @3.0mA [Volt] rms (Ta=25oC) (Ta=25oC) Note 1 (Ta=25oC) Note 3 Note 2: CCFL Frequency should be carefully determined to avoid interference between inverter and TFT LCD Note 3: The variance of CCFL power consumption is ± 10%. Calculator value for reference (ICFL×VCFL× 4=PCFL). Note 4: CCFL life time is determined as the time at which brightness of lamp is 50%. The typical life time of CCFL is on the condition at 7.5 mA lamp current. 6.0 Signal Characteristic 6.1 Pixel Format Image ver0.1 15/25 M170EG01 V.9 Product Specification Following figure shows the relationship of the input signals and LCD pixel format. ODD 1 ST E VEN ODD E VEN ODD E VEN RGBRGBRGB RGBRGBRGB 1024 TH RGBRGBRGB RGBRGBRGB 6.2 The input data format Note1: Normally, DE, VS, HS on EVEN channel are not used. Note2: Please follow PSWG. Note3: 8-bit in ver0.1 16/25 M170EG01 V.9 Product Specification 6.3 Signal Description The module using a pair of LVDS receiver SN75LVDS82(Texas Instruments) or compatible. LVDS is a differential signal technology for LCD interface and high speed data transfer device. Transmitter shall be SN75LVDS83(negative edge sampling) or compatible. The first LVDS port(RxOxxx) transmits odd pixels while the second LVDS port(RxExxx) transmits even pixels. PIN # SIGNAL NAME 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 RxOIN0RxOIN0+ RxOIN1RxOIN1+ RxOIN2RxOIN2+ VSS RxOCLKINRxOCLKIN+ RxOIN3RxOIN3+ RxEIN0RxEIN0+ VSS RxEIN1RxEIN1+ VSS RxEIN2RxEIN2+ RxECLKINRxECLKIN+ RxEIN3RxEIN3+ VSS VSS NC VSS VCC VCC VCC DESCRIPTION Negative LVDS differential data input (Odd data) Positive LVDS differential data input (Odd data) Negative LVDS differential data input (Odd data) Positive LVDS differential data input (Odd data) Negative LVDS differential data input (Odd data, H-Sync,V-Sync,DSPTMG) Positive LVDS differential data input (Odd data, H-Sync,V-Sync,DSPTMG) Power Ground Negative LVDS differential clock input (Odd clock) Positive LVDS differential clock input (Odd clock) Negative LVDS differential data input (Odd data) Positive LVDS differential data input (Odd data) Negative LVDS differential data input (Even data) Positive LVDS differential data input (Even data) Power Ground Positive LVDS differential data input (Even data) Negative LVDS differential data input (Even data) Power Ground Negative LVDS differential data input (Even data) Positive LVDS differential data input (Even data) Negative LVDS differential clock input (Even clock) Positive LVDS differential clock input (Even clock) Negative LVDS differential data input (Even data) Positive LVDS differential data input (Even data) Power Ground Power Ground No Connection ( for AUO test) Power Ground +5.0V Power Supply +5.0V Power Supply +5.0V Power Supply ver0.1 17/25 M170EG01 V.9 Product Specification Note1: Start from left side Connector 1 RxOIN0Note3: Please follow PSWG. 30 VCC Note2: Input signals of odd and even clock shall be the same timing. 6.4 Interface Timing 6.4.1 Timing Characteristics Basically, interface timings described here is not actual input timing of LCD module but output timing of SN75LVDS82DGG (Texas Instruments) or equivalent. Item Data CLK H-section V-section Period Display Area Period Display Area Symbol Tclk Th Tdisp(h) Tv Tdisp(v) F Min 40 685 640 1036 1024 49 Typ 54 844 640 1066 1024 60 Max 70 1024 640 2048 1024 76 Unit MHz Tclk Tclk Th Th Hz Frame Rate Note : DE mode only ver0.1 18/25 M170EG01 V.9 Product Specification 6.4.2 Timing diagram DE C LK DE Tclk Tblk(v) Th Tv Tdisp(h) Th Tdisp(v) Tblk(h) ver0.1 19/25 M170EG01 V.9 Product Specification 6.5 Power ON/OFF Sequence Vin power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals from any system shall be Hi-Z state or low level when Vin is off. 90% 90% Vin 0V 10% 10% 10% 10% T1 Signal 0V T2 T5 T6 T7 T3 T4 Lamp 0V Symbol T1 T2 T3 T4 T5 T6 T7 Min. 0.5 0 200 100 0 1000 V alues Typ. 16 - Max. 10 10 50 10 - Unit ms ms ms ms ms ms ms Note: The values of the table are follow PSWG. ver0.1 20/25 M170EG01 V.9 Product Specification 7.0 Connector & Pin Assignment Physical interface is described as for the connector on module. These connectors are capable of accommodating the following signals and will be following components. 7.1 TFT LCD Module Connector Name / Designation Manufacturer Type Part Number Mating Housing Part Number Pin# 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 Signal Name RxOIN0RxOIN1RxOIN2VSS RxOCLKIN+ RxOIN3+ RxEIN0+ RxEIN1VSS RxEIN2+ RxECLKIN+ RxEIN3+ VSS VSS VCC Interface Connector / Interface card JAE or compatible AL2307-A0G1D-P / FI-XB30SSRL-HF16 JAE FI-X30HL Pin# 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Signal Name RxOIN0+ RxOIN1+ RxOIN2+ RxOCLKINRxOIN3RxEIN0VSS RxEIN1+ RxEIN2RxECLKINRxEIN3VSS NC VCC VCC ver0.1 21/25 M170EG01 V.9 Product Specification 7.2 Backlight Unit Connector Name / Designation Manufacturer Type Part Number Mating Type Part Number Lamp Connector / Backlight lamp JST BHSR-02VS-1 SM02B-BHSS-1-TB 7.3 Signal for Lamp connector Connector No. CN1 Upper CN2 Pin No. 1 2 1 2 1 2 1 2 Input Hot1 Cold1 Hot2 Cold2 Hot1 Cold1 Hot2 Cold2 Color Pink White Blue Black Pink White Blue Black Function High Voltage Low Voltage High Voltage Low Voltage High Voltage Low Voltage High Voltage Low Voltage CN3 Lower CN4 ver0.1 22/25 M170EG01 V.9 Product Specification 8.0 Reliability Reliability test condition No Test Item 1 2 3 4 5 6 7 8 9 Temperature Humidity Bias (THB) High Temperature Operation (HTO) Low Temperature Operation (LTO) High Temperature Storage (HTS) Low Temperature Storage (LTS) Thermal Shock Test (TST) On/Off Test Shock Test (Non-Operating) Vibration Test (Non-Operating) Test Condition 50℃, 80%, 300hours 50℃, 300hours 0℃, 300hours 60℃, 300hours -20℃, 300hours -20℃/30min, 60℃/30min, 100 cycles On/10sec, Off/10sec, 30,000 cycles 50G, 20ms, Half-sine wave (+ X, + Y, + Z) 1.5G(10~200Hz P- P), 30 Minutes each Axis (X, Y, Z) Contact Discharge: ± 8KV, 150pF(330O ) 1sec, 8 points, 25 times/ point Air Discharge: ± 15KV, 150pF(330O ) 1sec, 8 points, 25 times/ point 11 Altitude Test Operation:10,000 ft Non-Operation:30,000 ft 12 Drop Test The drop height is 60cm 10 ESD (ElectroStatic Discharge) ver0.1 23/25 M170EG01 V.9 Product Specification 9.0 Safety 9.1 Sharp Edge Requirements There will be no sharp edges or comers on the display assembly that could cause injury. 9.2 Materials 9.2.1 Toxicity There will be no carcinogenic materials used anywhere in the display module. If toxic materials are used, they will be reviewed and approved by the responsible AUO Toxicologist. 9.2.2 Flammability All components including electrical components that do not meet the flammability grade UL94-V1 in the module will complete the flammability rating exception approval process. The printed circuit board will be made from material rated 94-V1 or better. The actual UL flammability rating will be printed on the printed circuit board. 9.3 Capacitors If any polarized capacitors are used in the display assembly, provisions will be made to keep them from being inserted backwards. 10.0 Other requirement 10.1 National Test Lab Requirement The display module will satisfy all requirements for compliance to UL 1950, First Edition CSA C22.2 No.950-M89 EEC 950 EN 60 950 U.S.A. Information Technology Equipment Canada, Information Technology Equipment International, Information Technology Equipment International, Information Processing Equipment (European Norm for IEC950) 10.2 Label The label is on the panel as shown below: ver0.1 24/25 11.0 Mechanical Characteristics Ver0.2 25/24 Ver0.2 26/25