TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
1
Overview
Features
•
Single-wire LIN transceiver for transmission rates up to 20 kBit/s
•
Compliant to ISO 17987-4, LIN specification 2.2 A and SAE J2602
•
5 V or 3.3 V low drop-out linear voltage regulator with 70 mA current
capability
•
Stable with ceramic output capacitor of 1 µF
•
Ultra low current consumption in sleep mode of max. 16 µA
•
Ultra low current consumption in standby mode of typical 20 µA
•
Very low leakage current on the BUS pin
•
VCC undervoltage detection with RESET output
•
TxD protected with dominant time-out function
•
BUS short to VBAT protection and BUS short to GND handling
•
Overtemperature protection and supply undervoltage detection
•
Very high ESD robustness: ±8 kV according to IEC61000-4-2
•
Optimized for high electromagnetic compatibility (EMC);
Very low emission and high immunity to interference
•
Available in standard PG-DSO-8 and leadless PG-TSON-8 packages
•
PG-TSON-8 package supports automated optical inspection (AOI)
•
Green Product (RoHS compliant)
Potential applications
•
LIN slave satellite modules
•
Window lifters
•
Rain and light sensors
•
Sun roof control modules
•
Wiper modules
•
Ambient lighting
Data Sheet
www.infineon.com/Automotive-Transceivers
1
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Overview
Product validation
Qualified for automotive applications. Product validation according to AEC-Q100.
Description
The TLE8457C / TLE8457D is a monolithic integrated LIN transceiver and low drop-out voltage regulator. The
device is designed to supply a microcontroller and peripherals with up to 70 mA, provide protection through
VCC undervoltage reset, while also offering bi-directional bus communication compliant to LIN specification
2.2 A and SAE J2602. With the ultra low quiescent current consumption of typical 20 µA in standby mode the
TLE8457C / TLE8457D is especially suited for applications that are permanently supplied by the battery.
Based on the Infineon BiCMOS technology the TLE8457C / TLE8457D provide excellent ESD robustness
together with a very high level of electromagnetic compatibility (EMC). The TLE8457C / TLE8457D is
AEC qualified and tailored to withstand the harsh conditions of the automotive environment.
Type
LDO VCC output
voltage
Package
Marking
Init timeout
feature1)
TLE8457CSJ
5V
PG-DSO-8
8457C
No
TLE8457CLE
5V
PG-TSON-8
8457C
No
TLE8457DSJ
3.3 V
PG-DSO-8
8457D
No
TLE8457DLE
3.3 V
PG-TSON-8
8457D
No
1) “Init timeout feature” is only available with TLE8457A & TLE8457B.
Data Sheet
2
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Table of contents
1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Potential applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Product validation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3
3.1
3.2
Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pin assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pin definitions and functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4
4.1
4.1.1
4.1.2
4.1.3
4.1.4
4.1.5
4.2
4.2.1
4.2.2
4.3
4.3.1
4.3.2
4.4
4.4.1
4.4.2
4.5
Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Normal operation mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Standby mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Sleep mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Bus wake-up event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Mode transition via EN pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Power supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Power-up and power-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
VS undervoltage detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Voltage regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
VCC undervoltage detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Reset output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
LIN transceiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
TxD time-out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Short-circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Overtemperature protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5
5.1
5.2
5.3
General product characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Functional range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thermal characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
6.1
6.2
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Functional device characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
7
7.1
7.2
7.3
7.4
Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Application example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ESD robustness according to IEC61000-4-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transient robustness according to ISO 7637-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LIN physical layer compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
9
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Data Sheet
3
17
17
18
19
27
27
28
28
28
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Block diagram
2
Block diagram
Linear Regulator
8
Bandgap
Reference
VCC
Driver
Current Limitation
VCC Undervoltage
Detection
Control
VS
VCC
1
RNRST
7
NRST
Supply Monitor
Rslave
Control
Wake
Receiver
2
EN
VCC
REN
Over-Temperature
and Over-Current
Protection
BUS
4
RTxD
Transmitter
6
Driver
TxD
Time-Out
VCC
Receiver
GND
Figure 1
Data Sheet
3
BUS
RFFilter
VS / 2
5
RxD
Block diagram
4
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Pin configuration
3
Pin configuration
3.1
Pin assignment
VS
1
8
VCC
EN
2
7
NRST
GND
3
6
TxD
BUS
4
5
VS
1
8
VCC
EN
2
7
NRST
6
TxD
5
RxD
GND
3
BUS
4
RxD
(PAD)
PG-TSON-8
(Top side X-Ray view)
PG-DSO-8
Figure 2
Pin configuration
3.2
Pin definitions and functions
Pin
Symbol
Function
1
VS
Battery supply voltage;
Decoupling capacitor required
2
EN
Enable input;
Integrated pull-down resistor
Logic “high” to select normal operation mode
3
GND
Ground
4
BUS
BUS input/output;
Integrated LIN slave termination
5
RxD
Receive data output;
Monitors the LIN bus signal in normal operation mode
Indicates a wake-up event in standby mode
6
TxD
Transmit data input;
Integrated pull-up resistor
Logic “low” to drive a dominant signal on the LIN bus
7
NRST
8
VCC
Undervoltage reset output;
Integrated pull-up resistor
Logical “low” during reset
Voltage regulator output;
Output capacitor requirements specified in functional device characteristics
PAD1)
–
Connect to PCB heat sink area. Do not connect to other potential than GND
1) Only available with PG-TSON8 package.
Data Sheet
5
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Functional description
4
Functional description
4.1
Operating modes
The operation mode of the TLE8457C / TLE8457D is controlled with the EN and TxD input pins (see Figure 3
and Table 2). The TLE8457C / TLE8457D has 3 major operation modes:
•
Normal operation mode
•
Standby mode
•
Sleep mode
Standby Mode
LIN transceiver: Off
LDO regulator: On
EN: Low
RxD: Wake-up source1)
NRST: High2)
1
1
T=
LE
=1
EN
ST
NR
6
an
d
HI
W
RS
dN
an
up
BUS Wake-up
e-
ak
3
7
W
2
S
EN
BU
Tx
D
=1
Power-up
Normal Operation Mode
LIN transceiver: On
LDO regulator: On
EN: High
NRST: High2)
Sleep Mode
EN
5
4
EN
AND
TxD
LIN transceiver: Off
LDO regulator: Off
EN: Low
NRST: Low
and NRST=1
1)
Wake-up Source:
RxD: logical „high“ after Power-up or transistion with EN input
RxD: logical „low“ after BUS Wake-up detection
2)
Reset:
- An undervoltage (VCC < VCC,UV) on VCC is signaled with NRST goes „low“
- If NRST is „low“ the transceiver is disabled
- NRST will stay „low“ for the time tRST after VCC powered up (VCC > VCC,UV)
Figure 3
Operation mode state diagram
Table 1
Operation mode transitions
TLE8457CD_MODE_DIAGRAM
No. Reason for transition
Comment
1
Power-on detection
The VS supply voltage rise above the VS,PON power-on reset level.
2
Mode change with EN input
Triggered by logic “high” level. VCC has to be in the functional
range.
3
Mode change with EN and TxD inputs Triggered by logic “low” level on EN while TxD is held “high”.
VCC has to be in the functional range.
4
Mode change with EN and TxD inputs Triggered by logic “low” level on EN and TxD. VCC has to be in the
functional range.
5
Mode change with EN input
Data Sheet
Triggered by logic “high” level.
6
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Functional description
Table 1
Operation mode transitions (cont’d)
No. Reason for transition
Comment
6
Bus wake-up detection
RxD is set “low” for signalling the bus wake-up event to the
microcontroller.
7
Bus wake-up detection in standby
mode
RxD is set “low” for signalling the bus wake-up event to the
microcontroller. Operating mode is not changed.
Table 2
Mode
Sleep
Operating mode control
Control
Functionality
EN
TxD
Low
Low
1)
Comments
VCC
NRST
RxD
Off
Low
Floating
–
2)
Low
High
On
High
Low
High
RxD “low” after a bus wake-up
RxD “high” after power-up or reset
Normal
High
operation
Low
High
On
High2)
Low
High
RxD reflects the signal on the bus
TxD driven by the microcontroller
Standby
1) The TxD input has a pull-up structure to VCC and is per default set to logic “high” if left open.
2) NRST is logic “low” during VCC undervoltage and while issuing a reset pulse to the microcontroller.
Data Sheet
7
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Functional description
4.1.1
Normal operation mode
In normal operation mode both the voltage regulator and the LIN transceiver are active. The TLE8457C /
TLE8457D supports data transmission rates up to 20 kBit/s. Data from the microcontroller is transmitted to
the LIN bus via the TxD input, while the receiver detects the data stream on the LIN bus and forwards it to the
RxD output.
After entering normal operation mode the TLE8457C / TLE8457D requires a logic “high” signal for the time
tto,rec on the TxD input before releasing the data communication. The transmitter remains deactivated as long
as the signal on the TxD input pin remains logic “low”, preventing possible bus communication disturbance
(see Figure 4).
From normal operation mode the TLE8457C / TLE8457D can be set to standby mode or sleep mode.
EN
tMODE,HIGH
tMODE,LOW
t
VCC
t
NRST
t
Data transmission
RxD
tto,rec
t
Data transmission
TxD
t
Standby mode
Normal Operation mode
Sleep mode
TLE8457_NORMAL_MODE
Figure 4
4.1.2
Entering normal operation mode, transition to sleep mode
Standby mode
Standby mode is a low power mode with ultra low quiescent current consumption while the voltage regulator
remains active, supplying for example a microcontroller in stop mode. No LIN bus communication is possible,
the transmitter and the receiver are disabled. The low power receiver is still active and the device can wake up
by a message from the LIN bus.
For changing the operation mode from standby mode to sleep mode, the device has to be set to normal
operation mode first, then to sleep mode (see Figure 4).
Data Sheet
8
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Functional description
VS
VS,PON
t
LIN
tWK,bus
t
VCC
t
NRST
t
RxD
RxD signals Power-up
RxD signals Bus Wake-up
t
The device remains in Standby mode
while the signal on the EN pin is „low“
EN
t
Un-powered
Standby mode
Normal Operation mode
TLE8457CD_STANDBY_MODE
Figure 5
Entering standby mode after power-up
In standby mode the TLE8457C / TLE8457D indicates wake-up information on the RxD output. After a powerup and reset event, the RxD output will be “high”. If the TLE8457C / TLE8457D is in standby mode after bus
wake-up detection, the RxD output will be “low”.
Data Sheet
9
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Functional description
4.1.3
Sleep mode
Sleep mode is a low power mode with quiescent current consumption reduced to a minimum while the device
can still wake up by a message from the LIN bus. Both the transceiver and the voltage regulator are switched
off.
4.1.4
Bus wake-up event
A bus wake-up event, also called remote wake-up, causes a transition from a low power mode to standby
mode. A falling edge on the LIN bus, followed by a dominant BUS signal for the time tWK,bus results in a bus
wake-up event. The mode change to standby mode becomes active with the following rising edge on the LIN
bus, when BUS voltage exceeds VBUS,wk. The TLE8457C / TLE8457D remains in low power mode until it detects
a state change on the LIN bus from dominant to recessive (see Figure 6). In standby mode a logic “low” signal
on the RxD output indicates a bus wake-up event.
In case the TLE8457C / TLE8457D detects a bus wake-up event while already being in standby mode, the wakeup event will be signalled with a logic “low” level on RxD and override the previous wake source (see Figure 5).
VBUS
VBUS,dom
VBUS,wk
tWK,bus
t
Sleep mode
Standby mode
VCC,UV,ON
VCC
t
tRST
NRST
t
EN
t
TxD is „high“ because of internal
pull-up structure
TxD
t
RxD „low“ indicates a Bus
Wake-up event
RxD
t
TLE8457CD_BUS_WAKE
Figure 6
Data Sheet
Bus wake-up behavior
10
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Functional description
4.1.5
Mode transition via EN pin
The EN input is used for operation mode control of the TLE8457C / TLE8457D. By setting the EN input logic
“high” for the time tMODE,HIGH while being in standby mode, a transition to normal operation mode will be
triggered.
If the voltage level at the EN input is set logic “high” while the TLE8457C / TLE8457D is in sleep mode, a
transition to normal mode is initiated.
From normal operation mode the TLE8457C / TLE8457D can be set to either sleep mode or standby mode. If
the EN input is set “low” for the time tMODE,LOW while the TxD input is held at logic “high”, the mode will change
to standby mode. For a transition to sleep mode, the TxD must be set to logic “low” before the time tMODE,LOW
elapses after EN goes “low” (see Figure 7). It is recommended to program a short delay time from when EN is
set “low” until TxD is set “low”, to prevent driving the BUS dominant through mode transition to sleep mode.
The EN input has an integrated pull-down resistor to ensure the device remains in a low power mode if the EN
input is left open. The EN input has an integrated hysteresis (see Figure 7).
The TLE8457C / TLE8457D changes the operation modes regardless of the signal on the BUS pin. In the case of
a short circuit failure between the LIN bus and GND, resulting in a permanent dominant signal, the TLE8457C
/ TLE8457D can be set to sleep mode.
VEN,ON
EN
EN hysteresis
VEN,OFF
tMODE,LOW
tMODE,LOW
tMODE,HIGH
t
tMODE,HIGH
TxD
tRST
t
NRST
t
Normal Operation
mode
Standby mode
Normal Operation
mode
Sleep mode
Normal Operation mode
TLE8457CD_MODE_CONTROL
Figure 7
Operation mode control
The EN input is blocked while the TLE8457C / TLE8457D is in normal operation mode or standby mode and
NRST is “low”, indicating an undervoltage on Vcc. After the NRST output goes “high”, mode control with the EN
input is released again.
4.2
Power supplies
The TLE8457C / TLE8457D is designed for being supplied by the battery line through an external reverse
polarity protection diode at the VS pin (see Figure 16). An input capacitor is needed for damping input line
transients.
4.2.1
Power-up and power-down
During power-up the TLE8457C / TLE8457D will enter standby mode when the VS supply reaches the power-on
reset level VS,PON. The voltage regulator output VCC will track the VS supply voltage until VCC reaches its nominal
voltage level. As VCC reaches the undervoltage level VCC,UV, the NRST output will stay logic “low” for the reset
Data Sheet
11
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Functional description
time tRST and then be set logic “high”. As NRST goes “high”, the EN input will become active and the TLE8457C
/ TLE8457D can change operating mode accordingly (see Table 2).
VS
VS,UV,ON
VS,UV,OFF
VCC
VS
VCC,UV
VCC
VCC,UV
VS,PON
VS,PON
t
tRST
NRST
t
EN
t
un-powered
Standby mode
Normal Operation mode
Transmission blocked
Figure 8
un-powered
TLE8457CD_VS_POWER-UP_DOWN
Power-up and power-down behavior
While powering down while in normal operation mode the TLE8457C / TLE8457D will block the LIN transmitter
as the VS supply voltage falls below VS,UV,OFF. The voltage regulator will start tracking the VS supply voltage
when falling below VCC + VDR. As VCC falls below the undervoltage level VCC,UV, the NRST output will be set logic
“low”. When the VS supply voltage falls below the power-on-reset level VS,PON the voltage regulator will be
disabled and the TLE8457C / TLE8457D will be considered unpowered.
Data Sheet
12
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Functional description
4.2.2
VS
VS undervoltage detection
Undervoltage release level VS,UV,ON
Undervoltage blocking level VS,UV,OFF
Undervoltage hysteresis VS,UV,hys
Power-on reset level VS,PON
Blanking time tblank,UV
t
Normal Operation mode
No communication possible
Normal Operation mode
TLE8457_VS_EARLY_UNDERVOLTAGE_A
Figure 9
VS early undervoltage detection
The TLE8457C / TLE8457D has an undervoltage detection on the supply pin VS with two different thresholds:
•
In normal operation mode the TLE8457C / TLE8457D blocks the communication between the LIN bus and
the microcontroller when detecting an early undervoltage event. The RxD output will be set “high”.
However, no mode change will occur. After VS rises above the undervoltage release level VS,UV,REL, the bus
communication interface will be released as soon as the signal on the TxD input goes “high” (see Figure 9).
•
When the power supply VS drops below the power-on reset level VS,PON the TLE8457C / TLE8457D not only
blocks the transceiver communication, it also changes the operation mode to standby mode after recovery
of VS, see Figure 10. In standby mode the TLE8457C / TLE8457D indicates a power-up event on the RxD pin.
The power-on reset detection is active in all operation modes.
VS
Undervoltage release level VS,UV,ON
Undervoltage blocking level VS,UV,OFF
Undervoltage hysteresis VS,UV,hys
Power-on reset level VS,PON
Blanking time tblank,UV
Power-down
Normal Operation mode
No communication possible
Figure 10
Data Sheet
t
Standby mode (EN = “low“)
Normal Operation mode (EN = “high“)
TLE8457CD_VS_UNDERVOLTAGE_A
VS undervoltage detection
13
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Functional description
4.3
Voltage regulator
The TLE8457C / TLE8457D has an integrated voltage regulator dedicated for supplying microcontrollers
and/or on-board sensors under harsh automotive environment conditions. It can supply a load current up to
70 mA with an output voltage tolerance within ± 2%. Because of the ultra low current consumption, the
TLE8457C / TLE8457D is perfectly suited for applications permanently connected to the battery supply.
Additionally, in sleep mode, the voltage regulator is switched off and an even lower quiescent current can be
achieved.
The voltage regulator output is protected against undervoltage, overcurrent, overtemperature and power-up
failures. In case the load current rises above the functional range, for example during VCC short circuits, the
output current is limited to ICC,lim. Therefore the VCC output voltage will drop. A reset pulse will be issued if VCC
falls below the undervoltage reset threshold.
The VCC supply output provides a stable supply voltage with output capacitors down to 1 µF, including low ESR
multi-layer ceramic capacitors.
4.3.1
VCC undervoltage detection
The TLE8457C / TLE8457D has an undervoltage detection feature on the voltage regulator VCC output. If the VCC
voltage falls below the undervoltage threshold VCC,UV for longer than detection time tdet,RST, the NRST output
will be set logic “low” and the transceiver will be deactivated.
tdet,RST
VCC,UV
VCC
t
Normal Operation mode (EN = „high“)
Standby mode (EN = „low“)
tRST
NRST
t
NRST goes and stays „low“ as
long as VCC is in undervoltage
Figure 11
4.3.2
NRST stays „low“ for
additional Reset time tRST
TLE8457CD_VCC_UNDERVOLTAGE
VCC undervoltage detection
Reset output
The NRST output is used for issuing reset pulses, for example to an external microcontroller. In case of voltage
regulator undervoltage or overtemperature events, the NRST output will go “low” and the transceiver is
deactivated. The NRST output will stay “low” until a complete recovery from the failure is achieved. After the
additional time tRST has elapsed NRST will go “high” (see Figure 11).
While NRST is “low” mode transition is blocked.
The NRST pin has an internal pull up to VCC. If needed in the application, an additional external pull-up resistor
can be implemented.
Data Sheet
14
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Functional description
4.4
LIN transceiver
The LIN interface is a single wire, bi-directional bus, used for in-vehicle networks. The integrated LIN
transceiver of the TLE8457C / TLE8457D is the interface between the microcontroller and the physical LIN bus
(see Figure 16). Data from the microcontroller is driven to the LIN bus via the TxD input. The transmit data
stream on the TxD input is converted to a LIN bus signal with optimized slew rates in order to minimize the
electromagnetic emission of the LIN network. The RxD output reads back the information from the LIN bus to
the microcontroller. The receiver has an integrated filter network for noise suppression from the LIN bus and
to increase the electromagnetic immunity level of the transceiver.
The LIN specification defines two valid bus levels (see Figure 12):
•
Dominant state with the LIN bus voltage level near GND, actively driven by a transceiver.
•
Recessive state with the LIN bus voltage pulled up to the supply voltage VS through the bus termination.
By setting the TxD input of the TLE8457C / TLE8457D to a logic “low” signal, the transceiver generates a
dominant level on the BUS interface pin. The receiver reads back the signal on the LIN bus and indicates the
dominant LIN bus signal with a logic “low” on the RxD output to the microcontroller. By setting the TxD input
“high”, the transceiver sets the LIN interface pin to the recessive level. At the same time the recessive level on
the LIN bus is indicated by a logic “high” signal on the RxD output.
Every LIN network consists of a master node and one or more slave nodes. To configure the TLE8457C /
TLE8457D for master node applications, a termination resistor of 1 kΩ and a diode must be connected
between the LIN bus and the power supply VS (see Figure 16).
VCC
TxD
t
VS
Recessive
Dominant
Recessive
Vth_REC
BUS
Vth_DOM
t
VCC
RxD
t
TLE8457_LIN_COMMUNICATION_A
Figure 12
Data Sheet
LIN bus signals
15
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Functional description
4.4.1
TxD time-out
The TxD time-out feature protects the LIN bus against permanent blocking in the case where the logical signal
on the TxD input is continuously “low”, caused by a malfunctioning microcontroller or a short circuit on the
printed circuit board for example. In normal operation mode, a logic “low” signal on the TxD input for time t >
tTxD disables the transmitter’s output driver stage (see Figure 13). The receiver will remain active and the data
on the BUS is still monitored on the RxD output.
The TLE8457C / TLE8457D will release the output stage after a TxD time-out event first when detecting a logic
“high” signal on the respective TxD input for the duration of tto,rec.
Recovery of the microcontroller error
TxD time-out due to e.g. microcontroller error
Release after TxD time-out
tTxD
tto,rec
Normal communication
Normal communication
TxD
t
VBUS
t
TLE8457_TXD_TIMEOUT_A
Figure 13
4.4.2
TxD time-out
Short-circuit
The BUS pin of TLE8457C / TLE8457D can withstand short-circuits to either GND or to the power supply VS. The
integrated overtemperature protection may disable the transmitter if a permanent short circuit on the BUS
pin causes the TLE8457C / TLE8457D to overheat.
4.5
Overtemperature protection
The TLE8457C / TLE8457D has two independent overtemperature detectors for protecting the device against
thermal overstress, namely on the voltage regulator pass element and on the LIN bus transmitter. In the case
where the junction temperature at the LIN transmitter increases above the thermal shut-down level TJSD, it will
be disabled until the junction temperature of the transmitter cools down below TJ < TJSD - ∆T. No other effect,
nor mode change, will occur. After the LIN transmitter overtemperature recovery, the TxD input requires a
logic “high” signal before restarting data transmission.
If an overtemperature event is detected on the voltage regulator, it will be disabled and the NRST output will
be set “low”. During the overtemperature condition no functionality of the TLE8457C / TLE8457D is available.
After the junction temperature cools down below TJ < TJSD - ∆T, the voltage regulator is reactivated and NRST
will be set “high” after delay time tRST.
Note:
Data Sheet
The overtemperature detection of the LIN transmitter and the voltage regulator are working
independently. Therefore either only the LIN transmitter or only the voltage regulator or both can be
switched off, depending on the circumstance. An example of only LIN transmitter overtemperature
could be bus short-circuit or severe electromagnetical injection.
16
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
General product characteristics
5
General product characteristics
5.1
Absolute maximum ratings
Table 3
Absolute maximum ratings voltages, currents and temperatures1)
All voltages with respect to ground; positive current flowing into pin; unless otherwise specified
Parameter
Symbol
Values
Min.
Typ.
Max.
Unit Note or
Test Condition
Number
Voltage
Supply input voltage
VS
-0.3
–
45
V
LIN Spec 2.2A (Par. 11) P_5.1.1
Bus input voltage
VBUS
-27
–
40
V
–
P_5.1.2
Logic voltages at EN and TxD
Vlogic,in
-0.3
–
7.0
V
–
P_5.1.3
Logic voltages at RxD and NRST
Vlogic,out
-0.3
–
VCC +
0.3
V
–
P_5.1.4
Voltage regulator output
VCC
-0.3
–
7.0
V
–
P_5.1.5
Output current at RxD
IRxD
-15
–
15
mA
–
P_5.1.6
Output current at NRST
INRST
–
–
10
mA
–
P_5.1.7
Junction temperature
Tj
-40
–
150
°C
–
P_5.1.8
Storage temperature
Ts
-55
–
150
°C
–
P_5.1.9
Electrostatic discharge voltage
at VS and BUS vs. GND
VESD
-8
–
8
kV
Human body model
(100 pF via 1.5 kΩ)2)
P_5.1.10
Electrostatic discharge voltage
all other pins
VESD
-2
–
2
kV
Human body model
(100 pF via 1.5 kΩ)2)
P_5.1.11
Electrostatic discharge voltage
corner pins
VESD
-750
–
750
V
Charged device
model3)
P_5.1.12
Electrostatic discharge voltage
at all other pins
VESD
-500
–
500
V
Charged device
model3)
P_5.1.13
Currents
Temperature
ESD susceptibility
1) Not subject to production test, specified by design.
2) ESD susceptibility, HBM according to ANSI/ESDA/JEDEC JS-001 (1.5 kΩ, 100 pF).
3) ESD susceptibility, charged device model “CDM” EIA / JESD 22-C101 or ESDA STM5.3.1.
Notes
1. Stresses above the ones listed here may cause permanent damage to the device. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
2. Integrated protection functions are designed to prevent IC destruction under fault conditions described in the
data sheet. Fault conditions are considered as ‘outside’ normal operating range. Protection functions are not
designed for continuous repetitive operation.
Data Sheet
17
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
General product characteristics
5.2
Table 4
Functional range
Operating range
Parameter
Symbol
Values
Min.
Typ.
Max.
Unit Note or
Test Condition
Number
Supply voltage range for normal VS(nor)
operation
5.5
–
28
V
LIN Spec 2.2A
Param. 10
P_5.2.12
Extended Supply Voltage Range VS(ext)
for Operation
3.0
–
40
V
Parameter deviations P_5.2.22
possible
1.0
–
–
µF
1)3)
P_5.2.3
P_5.2.4
P_5.2.5
Supply voltage
Stability requirement on VCC
Output capacitor range
Output capacitor ESR
CVCC
ESR(CVCC) –
–
5.0
Ω
2)3)
–
150
°C
3)
Thermal parameter
Junction temperature
Tj
-40
1) The minimum output capacitance requirement is applicable for a worst case capacitance tolerance of 30%.
2) Relevant ESR value at f = 10 kHz.
3) Not subject to production test, specified by design.
Note:
Data Sheet
Within the functional range the IC operates as described in the circuit description. The electrical
characteristics are specified within the conditions given in the related electrical characteristics
table.
18
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
General product characteristics
5.3
Thermal characteristics
Note:
This thermal data was generated in accordance with JEDEC JESD51 standards. For more
information, please visit www.jedec.org.
Table 5
Thermal resistance1)
Parameter
Symbol
Values
Min.
Typ.
Max.
Unit Note or
Test Condition
130
–
K/W
2)
60
–
K/W
2)
Number
Thermal resistance, PG-DSO-8 package version
Junction to ambient
RthJA
–
P_5.3.1
Thermal resistance, PG-TSON-8 package version
Junction to ambient
RthJA
Junction to ambient
–
–
Junction to ambient
190
–
P_5.3.2
K/W Footprint only
3)
2
P_5.3.5
–
70
–
K/W 300 mm heatsink on
PCB3)
P_5.3.6
Thermal shutdown temperature TJSD
160
180
200
°C
TJSD increasing
P_5.3.3
Thermal shutdown hysteresis
–
10
–
K
TJSD decreasing
P_5.3.4
Thermal shutdown junction temperature
ΔT
1) Not subject to production test, specified by design.
2) Specified RthJA value is according to Jedec JESD51-2,-5,-7 at natural convection on FR4 2s2p board; The product
(IC+package) was simulated on a 76.2 × 114.3 × 1.5 mm3 board with 2 inner copper layers (2 × 70 μm Cu,
2 × 35 μm Cu). Where applicable a thermal via array under the exposed pad contacted to the first inner copper layer.
3) Specified RthJA value is according to Jedec JESD51-3 at natural convection on FR4 1s0p board; The product
(IC+package) was simulated on a 76.2 × 114.3 × 1.5 mm3 board with 1 inner copper layer (1 × 70 μm Cu).
Data Sheet
19
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Electrical characteristics
6
Electrical characteristics
6.1
Functional device characteristics
Table 6
Electrical characteristics
5.5 V < VS < 28 V; RLIN = 500 Ω; -40°C < Tj < 150°C;
all voltages with respect to ground; positive current flowing into pin1); unless otherwise specified.
Parameter
Symbol
Values
Unit Note or Test Condition
Number
Min. Typ. Max.
Current Consumption
Current consumption at VS,
transmitter in recessive state
0.1
0.3
0.7
mA
ICC = 50 µA; without RLIN;
TxD = “high”; VBUS = VS;
NRST=”high”
P_6.1.1
Current consumption at VS,
IS,dom
transmitter in dominate state
0.1
1.0
3.0
mA
ICC = 50 µA; without RLIN;
TxD = “low”; VBUS = 0 V;
NRST=”high”
P_6.1.2
Current consumption at VS,
dominate state
IS,dom_max
70
71
73
mA
ICC = 70 mA; without RLIN;
TxD = “low”; VBUS = 0 V;
NRST=”high”
P_6.1.3
Current consumption at VS in
standby mode
IS,standby = IS - ICC
IS,standby
–
20
40
µA
Standby mode;
ICC = 50 µA;
VS = VBUS = 13.5 V;
NRST = TxD = “high”
P_6.1.4
Current consumption at VS in
sleep mode
IS,Sleep
–
7
16
µA
Sleep mode; VS = 13.5 V;
VBUS = VS; VCC = 0 V
P_6.1.5
Current consumption at VS in
sleep mode. BUS shorted to
GND
IS,SC_GND
250
–
800
µA
Sleep Mode;
VS = 13.5 V; VBUS = 0 V;
VCC = 0 V
P_6.1.6
VS,PON
–
–
3.0
V
–
P_6.1.7
Undervoltage threshold, VS on VS,UV,ON
4.7
5.15
5.5
V
Rising edge
P_6.1.8
Undervoltage threshold, VS off VS,UV,OFF
4.4
4.85
5.2
V
Falling edge
P_6.1.9
P_6.1.10
IS,rec
Power-up and power-down
Power-on reset level, VS on
Undervoltage hysteresis on VS VS,UV,hys
VS,UV,hys = VS,UV,ON - VS,UV,OFF
200
300
–
mV
2)
Undervoltage blanking time
tBLANK,UV
–
10
–
µs
2)
P_6.1.11
“High” level input voltage
VEN,ON
2
–
–
V
–
P_6.1.12
“Low” level input voltage
VEN,OFF
–
–
0.8
V
–
P_6.1.13
Input hysteresis
VEN,hys
50
200
–
mV
–
P_6.1.14
Pull-down resistance
REN
15
30
60
kΩ
–
P_6.1.15
Delay time for mode change,
EN → “low”
tMODE,LOW
10
–
50
µs
–
P_6.1.16
Enable input: EN
Data Sheet
20
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Electrical characteristics
Table 6
Electrical characteristics (cont’d)
5.5 V < VS < 28 V; RLIN = 500 Ω; -40°C < Tj < 150°C;
all voltages with respect to ground; positive current flowing into pin1); unless otherwise specified.
Parameter
Symbol
Values
Unit Note or Test Condition
Number
Min. Typ. Max.
Delay time for mode change,
EN → “high”
tMODE,HIGH
–
–
5
µs
2)
P_6.1.17
Input capacitance
Ci_EN
–
5
–
pF
2)
P_6.1.83
“High” level leakage current
INRST,H
–
–
5
µA
2)
P_6.1.19
“Low” level output voltage
VNRST
–
–
0.4
V
INRST = 1.5 mA; VCC > 1 V;
P_6.1.20
Reset time
tRST
4
10
16
ms
–
P_6.1.21
Internal pull-up resistance
RNRST
5
10
20
kΩ
–
P_6.1.22
Reset Output: NRST
Voltage regulator output, 5 V versions (TLE8457Cxx): VCC
Output voltage
VCC
4.9
5.0
5.1
V
0.05 mA < ICC < 70 mA;
5.8 V < VS < 28 V
P_6.1.23
Output voltage drop
VDR = VS - VCC 3)
VDR
–
250
650
mV
ICC < 70 mA
P_6.1.24
Output voltage drop, 50 mA
VDR = VS - VCC
VDR,50
–
180
480
mV
ICC < 50 mA
P_6.1.25
Output voltage drop, 20 mA
VDR = VS - VCC
VDR,20
–
80
200
mV
ICC < 20 mA
P_6.1.26
Output current limitation
ICC,lim
-150
–
-70
mA
0 V < VCC < 4.8 V
P_6.1.27
Load regulation
∆VCC,lo
–
25
50
mV
0.05 mA < ICC < 70 mA;
VS = 13.5 V
P_6.1.28
Line regulation
∆VCC,li
–
25
50
mV
ICC = 1 mA;
5.8 V < VS < 28 V
P_6.1.29
Power supply ripple rejection PSRR
50
60
–
dB
2)
ICC = 50 mA; f = 100 Hz;
Vr = 0.5 Vpp; VS = 13.5 V
P_6.1.30
Undervoltage reset threshold VCC,UV
4.27
4.4
4.5
V
VCC decreasing
P_6.1.31
Undervoltage reset hysteresis VCC,UV,hy
50
100
–
mV
–
P_6.1.32
µs
2)
VCC = 3.5 V
CNRST = 20 pF
P_6.1.33
Undervoltage detection time
tdet,RST
1
–
20
Voltage regulator output, 3.3 V versions (TLE8457Dxx): VCC
Output voltage
VCC
3.234 3.300 3.366 V
0.05 mA < ICC < 70 mA;
4.066 V < VS < 28 V
P_6.1.34
Output voltage drop
VDR = VS - VCC
VDR
–
380
770
mV
ICC < 70 mA
P_6.1.35
Output voltage drop, 50 mA
VDR = VS - VCC
VDR,50
–
280
550
mV
ICC < 50 mA
P_6.1.36
Output voltage drop, 20 mA
VDR = VS - VCC
VDR,20
–
110
220
mV
ICC < 20 mA
P_6.1.37
Data Sheet
21
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Electrical characteristics
Table 6
Electrical characteristics (cont’d)
5.5 V < VS < 28 V; RLIN = 500 Ω; -40°C < Tj < 150°C;
all voltages with respect to ground; positive current flowing into pin1); unless otherwise specified.
Parameter
Symbol
Values
Unit Note or Test Condition
Number
Min. Typ. Max.
Output current limitation
ICC,lim
-150
–
-70
mA
0 V < VCC < 3.1 V
P_6.1.38
Load regulation
∆VCC,lo
–
25
50
mV
0.05 mA < ICC < 70 mA;
VS = 13.5 V
P_6.1.39
Line regulation
∆VCC,li
–
25
50
mV
ICC = 1 mA;
4.066 V < VS < 28 V
P_6.1.40
Power supply ripple rejection PSRR
50
60
–
dB
2)
ICC = 50 mA; f = 100 Hz;
Vr = 0.5 Vpp; VS = 13.5 V
P_6.1.41
Undervoltage reset threshold VCC,UV
2.82
2.90
2.96
V
VCC decreasing
P_6.1.42
Undervoltage reset hysteresis VCC,UV,hy
33
66
–
mV
–
P_6.1.43
20
µs
2)
VCC = 2.31 V
CNRST = 20 pF
P_6.1.44
Undervoltage detection time
tdet,RST
1
“High” level output voltage
VRxD,H
0.8
–
× VCC
–
V
IRxD = -2 mA; VBUS = VS
P_6.1.45
“Low” level output voltage
VRxD,L
–
0.2
V
× VCC
IRxD = 2 mA; VBUS = 0 V
P_6.1.46
“High” level input voltage
range
VTxD,H
0.7
–
× VCC
–
V
Recessive state
P_6.1.47
“Low” level input voltage
range
VTxD,L
–
–
0.3
V
× VCC
Dominant state
P_6.1.48
Input hysteresis
VTxD,hys
200
–
–
mV
–
P_6.1.49
Pull-up resistance
RTxD
15
30
60
kΩ
–
P_6.1.50
TxD time-out
tTxD
8
18
28
ms
–
P_6.1.51
TxD recessive release time
tto,rec
–
–
10
µs
2)
P_6.1.52
P_6.1.93
–
Receiver output: RxD
–
Transmission input: TxD
Ci_TxD
–
5
–
pF
2)
Receiver threshold voltage,
recessive to dominant edge
Vth_dom
0.4
× VS
0.44
× VS
–
V
VS < 18 V;
P_6.1.53
Receiver dominant state
VBUSdom
-27
–
0.4
× VS
V
LIN Spec 2.2A (Par. 17)4)
P_6.1.54
Receiver threshold voltage,
dominant to recessive edge
Vth_rec
–
0.56
× VS
0.6
× VS
V
VS < 18 V;
P_6.1.55
Receiver recessive state
VBUSrec
0.6
× VS
–
40
V
LIN Spec 2.2A (Par. 18)5)
P_6.1.56
Receiver center voltage
VBUS_CNT
0.475 0.5
× VS × VS
0.525 V
× VS
LIN Spec 2.2A (Par. 19)6)
VS < 18V;
P_6.1.57
Input capacitance
BUS receiver: BUS
Data Sheet
22
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Electrical characteristics
Table 6
Electrical characteristics (cont’d)
5.5 V < VS < 28 V; RLIN = 500 Ω; -40°C < Tj < 150°C;
all voltages with respect to ground; positive current flowing into pin1); unless otherwise specified.
Parameter
Symbol
Values
Unit Note or Test Condition
Number
Min. Typ. Max.
Receiver hysteresis
VHYS
0.07
× VS
0.12
× VS
0.175 V
× VS
LIN Spec 2.2A (Par. 20)7)
VS < 18 V;
P_6.1.58
Wake-up threshold voltage
VBUS,wk
0.4
× VS
0.5
× VS
0.6
× VS
V
–
P_6.1.59
BUS recessive output voltage VBUS,ro
0.8
× VS
–
VS
V
TxD = “high”; Open load
P_6.1.60
BUS short-circuit current
IBUS_LIM
40
85
125
mA
VBUS = 18 V;
LIN Spec 2.2A (Par. 12);
P_6.1.61
Leakage current
IBUS_NO_GND -1
-0.5
–
mA
VS = 0 V; VBUS = -12 V;
LIN Spec 2.2A (Par. 15)
P_6.1.62
Leakage current
IBUS_NO_BAT
1
5
µA
VS = 0 V; VBUS = 18 V;
LIN Spec 2.2A (Par. 16)
P_6.1.63
Leakage current
IBUS_PAS_dom -1
-0.5
–
mA
VS = 18 V; VBUS = 0 V;
LIN Spec 2.2A (Par. 13)
P_6.1.64
Leakage current
IBUS_PAS_rec
–
1
5
µA
VS = 8 V; VBUS = 18 V;
Driver stage “off”;
TxD = “high”;
LIN Spec 2.2A (Par. 14)
P_6.1.65
Forward voltage serial diode
VSerDiode
0.4
–
1.0
V
ISerDiode = - 75 µA
LIN Spec 2.2A (Par.21)
P_6.1.66
BUS pull-up resistance
Rslave
20
40
60
kΩ
LIN Spec 2.2A (Par. 26)
P_6.1.67
BUS dominant output voltage VBUS,do
maximum load
–
1.4
V
VTxD = 0 V; RLIN = 500 Ω;
VS = 5.5 V;
P_6.1.68
–
BUS dominant output voltage VBUS,do
maximum load
–
2.0
V
VTxD = 0 V; RLIN = 500 Ω;
VS = 18 V;
P_6.1.98
–
–
30
pF
2)
P_6.1.95
–
150
µs
–
P_6.1.69
LIN Spec 2.2A (Par. 31)
CRxD = 20 pF
P_6.1.70
LIN Spec 2.2A (Par. 32)
trx_sym = trx_pdf - trx_pdr;
CRxD = 20 pF
P_6.1.71
BUS transmitter: BUS
Input capacitance
–
Ci_BUS
Dynamic transceiver characteristics: BUS
Dominant time for bus wakeup
tWK,bus
30
Propagation delay:
LIN bus dominant to
RxD “low”
LIN bus recessive to
RxD “high”
trx_pdft
1
3.5
6
µs
trx_pdr
1
3.5
6
µs
Receiver delay symmetry
trx_sym
-2
–
2
µs
Data Sheet
23
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Electrical characteristics
Table 6
Electrical characteristics (cont’d)
5.5 V < VS < 28 V; RLIN = 500 Ω; -40°C < Tj < 150°C;
all voltages with respect to ground; positive current flowing into pin1); unless otherwise specified.
Parameter
Symbol
Values
Unit Note or Test Condition
Number
Min. Typ. Max.
Duty cycle D1
(for worst case at 20 kBit/s)
D1
0.396 –
–
Duty cycle 1 8)
THRec(max) = 0.744 × VS;
THDom(max) = 0.581 × VS;
VS = 7.0 … 18 V;
tbit = 50 µs;
LIN Spec 2.2A (Par. 27)
P_6.1.72
D1
0.396 –
–
Duty cycle 1 8)
THRec(max) = 0.760 × VS;
THDom(max) = 0.593 × VS;
5.5 V < VS < 7.0 V;
tbit = 50 µs
P_6.1.73
D2
–
–
0.581
Duty cycle 2 8)
THRec(min) = 0.422 × VS;
THDom(min) = 0.284 × VS;
VS = 7.6 … 18 V;
tbit = 50 µs;
LIN Spec 2.2A (Par. 28)
P_6.1.74
D2
–
–
0.581
Duty cycle 2 8)
THRec(min) = 0.41 × VS;
THDom(min) = 0.275 × VS;
6.1 V < VS < 7.6 V;
tbit = 50 µs;
P_6.1.75
D3
0.417 –
–
Duty cycle 3 8)
THRec(max) = 0.778 × VS;
THDom(max) = 0.616 × VS;
VS = 7.0 … 18 V;
tbit = 96 µs;
LIN Spec 2.2A (Par. 29)
P_6.1.76
D3
0.417 –
–
Duty cycle 3 8)
THRec(max) = 0.797 × VS;
THDom(max) = 0.630 × VS;
5.5 V < VS < 7.0 V;
tbit = 96 µs;
P_6.1.77
D1 = tbus_rec(min) / 2 × tbit
Duty cycle D1
VS supply 5.5 V to 7.0 V
(for worst case at 20 kBit/s)
D1 = tbus_rec(min) / 2 × tbit
Duty cycle D2
(for worst case at 20 kBit/s)
D2 = tbus_rec(max) / 2 × tbit
Duty cycle D2
VS supply 6.1 V to 7.6 V
(for worst case at 20 kBit/s)
D2 = tbus_rec(max) / 2 × tbit
Duty cycle D3
VS supply 7.0 V to 18.0 V
(for worst case at 10.4 kBit/s)
D3 = tbus_rec(min) / 2 × tbit
Duty cycle D3
VS supply 5.5 V to 7.0 V
(for worst case at 10.4 kBit/s)
D3 = tbus_rec(min) / 2 × tbit
Data Sheet
24
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Electrical characteristics
Table 6
Electrical characteristics (cont’d)
5.5 V < VS < 28 V; RLIN = 500 Ω; -40°C < Tj < 150°C;
all voltages with respect to ground; positive current flowing into pin1); unless otherwise specified.
Parameter
Symbol
Values
Unit Note or Test Condition
Number
Min. Typ. Max.
Duty cycle D4
VS supply 7.6 V to 18.0 V
(for worst case at 10.4 kBit/s)
D4
–
–
0.590
Duty cycle 4 8)
THRec(min) = 0.389 × VS;
THDom(min) = 0.251 × VS;
VS = 7.6 … 18 V;
tbit = 96 µs;
LIN Spec 2.2A (Par. 30)
P_6.1.78
D4
–
–
0.590
Duty cycle 4 8)
THRec(min) = 0.378 × VS;
THDom(min) = 0.242 × VS;
6.1 V < VS < 7.6 V;
tbit = 96 µs;
P_6.1.79
D4 = tbus_rec(max) / 2 × tbit
Duty cycle D4
VS supply 6.1 V to 7.6 V
(for worst case at 10.4 kBit/s)
D4 = tbus_rec(max) / 2 × tbit
1)
2)
3)
4)
5)
6)
7)
8)
Load current on VCC specified positive direction out of pin.
Not subject to production test, specified by design.
Measured when the output voltage VCC has dropped 100 mV from the nominal value obtained at VS = 13.5 V.
Minimum limit specified by design.
Maximum limit specified by design.
VBUS_CNT = (Vth_dom + Vth rec) / 2.
VHYS = Vth_rec - Vth_dom.
BUS load according to LIN Spec 2.2A:
Load 1 = 1 nF / 1 kΩ = CBUS / RLIN
Load 2 = 6.8 nF / 660 Ω = CBUS / RLIN
Load 3 = 10 nF / 500 Ω = CBUS / RLIN
Data Sheet
25
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Electrical characteristics
6.2
Diagrams
VCC
VS
CVCC
100 nF
NRST
CNRST
EN
RLIN
TxD
BUS
RxD
CBus
CRxD
GND
TLE8457_TEST_CIRCUIT_A
Figure 14
Simplified test circuit for dynamic transceiver characteristics
tBit
tBit
tBit
TxD
(input to transmitting node)
tBus_dom(max)
tBus_rec(min)
THRec(max)
Thresholds of receiving node 1
THDom(max)
VSUP
(Transceiver supply of
transmitting node)
THRec(min)
Thresholds of receiving node 2
THDom(min)
tBus_dom(min)
tBus_rec(max)
RxD
(output of receiving node 1)
trx_pdf(1)
trx_pdr(1)
RxD
(output of receiving node 2)
trx_pdr(2)
trx_pdf(2)
Duty Cycle D1, D3 = tBUS_rec(min) / (2 x tBIT)
Duty Cycle D2, D4 = tBUS_rec(max) / (2 x tBIT)
Figure 15
Data Sheet
TLE8457_LIN_TIMING_DIAGRAM_A
Timing diagram for dynamic transceiver characteristics
26
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Application information
7
Application information
Note:
The following information is given as a hint for the implementation of the device only and shall not
be regarded as a description or warranty of a certain functionality, condition or quality of the device.
7.1
Application example
VBat
5 V or 3.3V
VQ
VI
22μF
100nF
VCC
1μF
100nF
TLE42xx
LIN
BUS
GND
INH
Master Node
2.4kΩ
7
8
VS
Pull-Up
to MCU
Supply
Micro Controller
e.g XC22xx
INH
100nF
TLE7258
1
RxD
1kΩ
4
TxD
6
2
EN
BUS
GND
1nF
GND
5
ECU_1
1
22μF
VS
VCC
100nF
8
1μF
VCC
100nF
Slave Node
TLE8457
5
RxD
7
Micro Controller
e.g XC22xx
NRST
TxD
4
2
BUS
220pF
6
EN
GND
GND
3
ECU_X
Figure 16
Data Sheet
Simplified application circuit
27
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Application information
7.2
ESD robustness according to IEC61000-4-2
Test for ESD robustness according to IEC61000-4-2 (150 pF, 330 Ω) have been performed. The results and test
conditions are available in a separate test report.
Table 7
ESD robustness according to IEC61000-4-2
Performed Test
Results
Electrostatic discharge voltage at pin VS, BUS versus GND
Electrostatic discharge voltage at pin VS, BUS versus GND
+8
-8
Unit
Remarks
kV
1)
kV
1)
Positive pulse
Negative pulse
1) ESD susceptibility according LIN EMC 1.3 Test Specification, Section 4.3. (IEC 61000-4-2) - Tested by external test
house.
7.3
Transient robustness according to ISO 7637-2
Test for transient robustness according to ISO 7637-2 have been performed. The results and test conditions
are available in a separate test report.
Table 8
Automotive transient robustness according to ISO 7637-2
Performed Test
Results
Unit
Pulse 1
-100
V
Pulse 2
+75
V
Pulse 3a
-150
V
Pulse 3b
+100
V
7.4
LIN physical layer compatibility
As the LIN physical layer is independent from higher LIN layers (for example LIN protocol layer), all nodes with
a LIN physical layer corresponding to this revision can be mixed with LIN physical layer nodes, which are
according to older revisions (LIN 1.0, LIN 1.1, LIN 1.2, LIN 1.3, LIN 2.0, LIN 2.1 and LIN 2.2), without any
restrictions.
Data Sheet
28
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Package information
Package information
0.2
8
5
1
4
5 -0.2 1)
M
0.19 +0.06
B
0.1
2)
0.41+0.1
-0.06
C
8 MAX.
1.27
0.35 x 45˚
4 -0.2 1)
1.75 MAX.
0.175 ±0.07
(1.45)
8
0.64 ±0.25
6 ±0.2
A B 8x
0.2
M
C 8x
A
Index Marking
1) Does not include plastic or metal protrusion of 0.15 max. per side
2) Lead width can be 0.61 max. in dambar area
GPS01181
0
+0.05
1±0.1
PG-DSO-8 (Plastic dual small outline PG-DSO-8)1)
0.2 ±0.1
Pin 1 Marking
1.63 ±0.1
0.25 ±0.1
3 ±0.1
0.05
Z
0.65 ±0.1
0.38 ±0.1
1.58 ±0.1
0.3 ±0.1
0.4 ±0.1
3 ±0.1
2.4 ±0.1
0.81 ±0.1
0.1 ±0.1
0.56 ±0.1
Figure 17
Pin 1 Marking
0.3 ±0.1
PG-TSON-8-1-PO V01
Z (4:1)
0.07 MIN.
Figure 18
PG-TSON-8 (Plastic thin small outline nonleaded PG-TSON-8)1)
Green Product (RoHS compliant)
To meet the world-wide customer requirements for environmentally friendly products and to be compliant
with government regulations the device is available as a green product. Green products are RoHS-Compliant
(i.e Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020).
Further information on packages
https://www.infineon.com/packages
1) Dimensions in mm
Data Sheet
29
Rev. 1.1
2018-10-15
TLE8457C / TLE8457D
LIN Transceiver with integrated voltage regulator
Revision history
9
Revision history
Revision
Date
Changes
1.1
2018-10-15
Data Sheet updated:
1.0
Data Sheet
2018-01-22
•
Updated to new layout style
•
Editorial changes
Data Sheet created
30
Rev. 1.1
2018-10-15
Trademarks
All referenced product or service names and trademarks are the property of their respective owners.
Edition 2018-10-15
Published by
Infineon Technologies AG
81726 Munich, Germany
© 2018 Infineon Technologies AG.
All Rights Reserved.
Do you have a question about any
aspect of this document?
Email: erratum@infineon.com
Document reference
Z8F60768586
IMPORTANT NOTICE
The information given in this document shall in no
event be regarded as a guarantee of conditions or
characteristics ("Beschaffenheitsgarantie").
With respect to any examples, hints or any typical
values stated herein and/or any information regarding
the application of the product, Infineon Technologies
hereby disclaims any and all warranties and liabilities
of any kind, including without limitation warranties of
non-infringement of intellectual property rights of any
third party.
In addition, any information given in this document is
subject to customer's compliance with its obligations
stated in this document and any applicable legal
requirements, norms and standards concerning
customer's products and any use of the product of
Infineon Technologies in customer's applications.
The data contained in this document is exclusively
intended for technically trained staff. It is the
responsibility of customer's technical departments to
evaluate the suitability of the product for the intended
application and the completeness of the product
information given in this document with respect to
such application.
For further information on technology, delivery terms
and conditions and prices, please contact the nearest
Infineon Technologies Office (www.infineon.com).
WARNINGS
Due to technical requirements products may contain
dangerous substances. For information on the types
in question please contact your nearest Infineon
Technologies office.
Except as otherwise explicitly approved by Infineon
Technologies in a written document signed by
authorized representatives of Infineon Technologies,
Infineon Technologies’ products may not be used in
any applications where a failure of the product or any
consequences of the use thereof can reasonably be
expected to result in personal injury.