15-21/G6C-FM1N2B/2T

EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet 1206 Package Chip LED (1.0mm Height) 15-21/G6C-FM1N2B/2T Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb-free. ․The product itself will remain with in RoHS complaint version Descriptions ․ The 15-21 SMD LED Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․ Backlighting in dashboard and switch. ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. Device Selection Guide Part No. 15-21/G6C-FM1N2B/2T Chip Emitted Color Resin Color Brilliant Yellow Green Water Clear Material AlGaInP Everlight Electronics Co., Ltd. http://www.everlight.com Device No:SZDSE-151-G33 Prepared date:30-Aug-2007 Rev 1 Prepared by: Libin Page: 1 of 10 EVERLIGHT ELECTRONICS CO.,LTD. 15-21/G6C-FM1N2B/2T 1.4 Package Outline Dimensions Note: Tolerances Unless Dimension ±0.1mm , Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Device No:SZDSE-151-G33 Prepared date:30-Aug-2007 Rev 1 Prepared by: Libin Page: 2 of 10 EVERLIGHT ELECTRONICS CO.,LTD. 15-21/G6C-FM1N2B/2T Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA IFP 60 mA Power Dissipation Pd 60 mW Electrostatic Discharge ESD 2000 V Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Soldering Temperature Tsol Peak Forward Current (Duty 1/10 @1KHz) Reflow Soldering : 260℃ for 10sec. Hand Soldering : 350℃ for 3 sec. Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Min. Typ. Max. Unit Luminous Intensity Iv 18.0 ----- 45.0 mcd Viewing Angle 2θ1/2 ----- 140 ----- deg Peak Wavelength λp ----- 575 ----- nm Condition IF =20mA Dominant Wavelength λd 570.0 ----- 574.5 nm Spectrum Radiation Bandwidth △λ ----- 20 ----- nm Forward Voltage VF 1.75 ----- 2.35 V Reverse Current IR ----- ----- 10 μA VR =5V Notes: 1.Tolerance of Luminous Intensity ±11% 2.Tolerance of Dominant Wavelength ±1nm 3.Tolerance of Forward Voltage ±0.1V Everlight Electronics Co., Ltd. http://www.everlight.com Device No:SZDSE-151-G33 Prepared date:30-Aug-2007 Rev 1 Prepared by: Libin Page: 3 of 10 EVERLIGHT ELECTRONICS CO.,LTD. 15-21/G6C-FM1N2B/2T Bin Range Of Dom. Wavelength Group F Bin Min Max CC2 570.0 571.5 CC3 571.5 573.0 CC4 573.0 574.5 Unit Condition nm IF=20mA Unit Condition mcd IF=20mA Unit Condition V IF=20mA Bin Range Of Luminous Intensity Bin Min Max M1 18.0 22.5 M2 22.5 28.5 N1 28.5 36.0 N2 36.0 45.0 Bin Range Of Forward Voltage Group B Bin Min Max 0 1.75 1.95 1 1.95 2.15 2 2.15 2.35 Notes: 1.Tolerance of Luminous Intensity ±11% 2.Tolerance of Dominant Wavelength ±1nm 3.Tolerance of Forward Voltage ±0.1V Everlight Electronics Co., Ltd. http://www.everlight.com Device No:SZDSE-151-G33 Prepared date:30-Aug-2007 Rev 1 Prepared by: Libin Page: 4 of 10 EVERLIGHT ELECTRONICS CO.,LTD. 15-21/G6C-FM1N2B/2T Typical Electro-Optical Characteristics Curves Everlight Electronics Co., Ltd. http://www.everlight.com Device No:SZDSE-151-G33 Prepared date:30-Aug-2007 Rev 1 Prepared by: Libin Page: 5 of 10 EVERLIGHT ELECTRONICS CO.,LTD. 15-21/G6C-FM1N2B/2T Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank xxxxxx xxxxxx REF: Forward Voltage Rank RoHS xxxxxxxxxxxx xxxx xxxxxxxx Reel Dimensions Note: Tolerances Unless Dimension ±0.1mm , Unit = mm Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel Everlight Electronics Co., Ltd. http://www.everlight.com Device No:SZDSE-151-G33 Prepared date:30-Aug-2007 Rev 1 Prepared by: Libin Page: 6 of 10 EVERLIGHT ELECTRONICS CO.,LTD. 15-21/G6C-FM1N2B/2T Note: Tolerances Unless Dimension ±0.1mm , Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Desiccant Label Reliability Test Items And Conditions Everlight Electronics Co., Ltd. http://www.everlight.com Device No:SZDSE-151-G33 Prepared date:30-Aug-2007 Rev 1 Prepared by: Libin Page: 7 of 10 EVERLIGHT ELECTRONICS CO.,LTD. 15-21/G6C-FM1N2B/2T The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% No. Items Test Condition 1 Reflow Soldering Temp. : 260℃±5℃ Min 5 sec. Test Sample Ac/Re Hours/Cycles Size 22 Pcs. 0/1 Temperature Cycle H : +100℃ 15min ∫ 5 min L : -40℃ 15min 300 Cycles 22 PCS. 0/1 3 Thermal Shock H : +100℃ 5min ∫ 10 sec L : -10℃ 5min 300 Cycles 22 PCS. 0/1 4 High Temperature Storage Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1 5 Low Temperature Storage Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1 7 High Temperature / High Humidity 85℃/85% RH 1000 Hrs. 22 PCS. 0/1 2 6 Min. Precautions For Use 1. Over-current-proof Everlight Electronics Co., Ltd. http://www.everlight.com Device No:SZDSE-151-G33 Prepared date:30-Aug-2007 Rev 1 Prepared by: Libin Page: 8 of 10 EVERLIGHT ELECTRONICS CO.,LTD. 15-21/G6C-FM1N2B/2T Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less(Floor life). However,it’s recommended that The LEDs should be used within 168 hours (7 days) after opening the package.If unused LED remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do Everlight Electronics Co., Ltd. http://www.everlight.com Device No:SZDSE-151-G33 Prepared date:30-Aug-2007 Rev 1 Prepared by: Libin Page: 9 of 10 EVERLIGHT ELECTRONICS CO.,LTD. 15-21/G6C-FM1N2B/2T soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 355,Zhong Shan North Rd ,WuJiang, Economy Development Zone(YunXi Area), Tel: 0512-63409123-1603 Fax: 0512-63409123-1510 http://www.everlight.com SongLing Town,WuJiang City,JiangSu PRC, China. Everlight Electronics Co., Ltd. http://www.everlight.com Device No:SZDSE-151-G33 Prepared date:30-Aug-2007 Rev 1 Prepared by: Libin Page: 10 of 10