MN36

Safety This symbol, adjacent to another symbol or terminal, indicates the user must refer to the manual for further information. This symbol, adjacent to a terminal, indicates that, under normal use, hazardous voltages may be present Double insulation 1. Improper use of this meter can cause damage, shock, injury or death. Read and understand this user manual before operating the meter. 2. Make sure any covers or battery doors are properly closed and ured. 3. Always remove the test leads before replacing the battery or fuses. 4. Inspect the condition of the test leads and the meter itself for any damage before operating the meter. Repair any damage before use. 5. Do not exceed the maximum rated input limits. 6. Use great care when making measurements if the voltages are greater than 25VAC rms or 35VDC. These voltages are considered a shock hazard. 7. Always discharge capacitors and remove power from the device under test before performing Diode, Resistance or Continuity tests. 8. Remove the battery from the meter if the meter is to be stored for long periods. 9. To avoid electric shock, do not measure AC current on any circuit whose voltage exceeds 250V AC. Input Limits Function Maximum Input VDC, VAC 600V AC/600V AC Resistance, Diode, Continuity 500V DC/AC mA DC 200mA DC 10A DC 10A DC (15 seconds max. every 15 min.) Frequency 250V DC/AC User’s Manual Specifications Function DC Voltage (V DC) Range 400.0mV 4.000V 40.00V 400.0V 600V AC Voltage (V AC) 50-60Hz 4.000V 40.00V 400.0V 600V DC Current 400.0µA 4000µA 40.00mA 200.0mA 10A ±(2.5% reading + 4 digits) AC Current (40 to 400Hz) 400.0µA 4000µA 40.00mA 200.0mA 10A Resistance 400.0Ω 4.000kΩ 40.00kΩ 400.0kΩ 4.000MΩ 20.00MΩ Capacitance 4.000nF 40.00nF 400.0nF 4.000µF 40.00µF 100µF Frequency 10.00Hz 100Hz 1.000kHz 10.00kHz 100.0kHz 1.000MHz Temp °F Temp °C 5.000MHz -40 to 1400°F Not specified -40 to 650°F; ±(1.0% rdg + 10 digits) 651 to 1400°F; ±(3% rdg + 10 digits) -20 to 400°C; ±(1.0% rdg + 10 digits) -20 to 750°C 400 to 750°C; ±(3% rdg + 10 digits) (probe accuracy not included) Sensitivity: 5.0Vrms ±(1.0% reading + 4 digits) 10Hz to 1MHz Not Specified ±(3.0% reading + 5 digits) Not specified ±(3.0% reading + 10 digits) ±(1.2% reading + 4 digits) ±(3% reading + 5 digits) ±(1.2% reading + 4 digits) ±(1.2% rdg + 5 d) ±(0.8% rdg + 4 d) ±(2% rdg + 5 d) 40-400Hz Accuracy ±(0.5% reading + 4 digits) MiniTecTM Series Model MN36 Auto-Ranging Mini MultiMeter ±(0.8% reading + 4 digits) 3999 Introduction Congratulations on your purchase of Extech’s MN36 Auto-Ranging Multimeter. This meter measures AC/DC Voltage, AC/DC Current, Resistance, Capacitance, Frequency, Temperature, Diode Test and Continuity. Proper use and care of this meter will provide many years of reliable service. ±(1.5% reading + 5 digits) Specifications Stated at 73oF ±10oF (23oC ±5 oC) and less than 70% RH Diode Test Test current of 0.6mA maximum, open circuit voltage 1.5V DC typical Continuity Check Audible signal will sound if the resistance is less than approximately