74ACTQ02

74ACTQ02 Quad 2-Input NOR Gate August 1990 Revised February 2005 74ACTQ02 Quad 2-Input NOR Gate General Description The ACTQ02 contains four, 2-input NOR gates. The ACTQ utilize Fairchild’s Quiet Series technology to guarantee quiet output switching and improved dynamic threshold performance. FACT Quiet Series¥ features GTO¥ output control and undershoot corrector in addition to a split ground bus for superior ACMOS performance. Features s ICC reduced by 50% s Guaranteed simultaneous switching noise level and dynamic threshold performance s Improved latch-up immunity s Outputs source/sink 24 mA s ACTQ02 has TTL-compatible inputs Ordering Code: Order Number 74ACTQ02SC 74ACTQ02SJ 74ACTQ02MTC 74ACTQ02PC Package Number M14A M14D MTC N14A Package Description 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow Pb-Free 14-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide 14-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide 14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300" Wide Device also available in Tape and Reel. Specify by appending suffix letter “X” to the ordering code. Pb-Free package per JEDEC J-STD-020B. Logic Symbol IEEE/IEC Connection Diagram Pin Descriptions Pin Names An, Bn On Description Inputs Outputs FACT¥, FACT Quiet Series¥, and GTO¥ are trademarks of Fairchild Semiconductor Corporation. © 2005 Fairchild Semiconductor Corporation DS010889 www.fairchildsemi.com 74ACTQ02 Absolute Maximum Ratings(Note 1) Supply Voltage (VCC) DC Input Diode Current (IIK) VI VI 0.5V to 7.0V 20 mA 20 mA 0.5V to VCC  0.5V 20 mA 20 mA 0.5V to VCC  0.5V r50 mA r50 mA 65qC to 150qC r300 mA 140qC Recommended Operating Conditions Supply Voltage (VCC) Input Voltage (VI) Output Voltage (VO) Operating Temperature (TA) Minimum Input Edge Rate ('V/'t) VIN from 0.8V to 2.0V VCC @ 4.5V, 5.5V 4.5V to 5.5V 0V to VCC 0V to VCC 0.5V VCC  0.5V DC Input Voltage (VI) DC Output Diode Current (IOK) VO VO 40qC to 85qC 125 mV/ns 0.5V VCC  0.5V DC Output Voltage (VO) DC Output Source or Sink Current (IO) DC VCC or Ground Current per Output Pin (ICC or IGND) Storage Temperature (TSTG) DC Latch-Up Source or Sink Current Junction Temperature (TJ) PDIP Note 1: Absolute maximum ratings are those values beyond which damage to the device may occur. The databook specifications should be met, without exception, to ensure that the system design is reliable over its power supply, temperature, and output/input loading variables. Fairchild does not recommend operation of FACT¥ circuits outside databook specifications. DC Electrical Characteristics Symbol VIH VIL VOH Parameter Minimum HIGH Level Input Voltage Maximum LOW Level Input Voltage Minimum HIGH Level Output Voltage VCC (V) 4.5 5.5 4.5 5.5 4.5 5.5 4.5 5.5 VOL Maximum LOW Level Output Voltage 4.5 5.5 4.5 5.5 IIN ICCT IOLD IOHD ICC VOLP VOLV VIHD VILD Maximum Input Leakage Current Maximum ICC/Input Minimum Dynamic Output Current (Note 3) Maximum Quiescent Supply Current Quiet Output |Maximum Dynamic VOL Quiet Output Minimum Dynamic VOL Minimum HIGH Level Dynamic Input Voltage Maximum LOW Level Dynamic Input Voltage 5.5 5.5 5.5 5.5 5.5 5.0 5.0 5.0 5.0 1.1 2.0 1.5 1.6 0.001 0.001 TA Typ 1.5 1.5 1.5 1.5 4.49 5.49 2.0 2.0 0.8 0.8 4.4 5.4 3.86 4.86 0.1 0.1 0.36 0.36 25qC TA 40qC to 85qC 2.0 2.0 0.8 0.8 4.4 5.4 3.76 4.76 0.1 0.1 0.44 0.44 Guaranteed Limits Units V V V VOUT VOUT IOUT VIN V IOH IOH V IOUT VIN V IOL IOL VI VI Conditions 0.1V 0.1V or VCC  0.1V or VCC  0.1V 50 PA VIL or VIH 24 mA 24 mA (Note 2) 50 PA VIL or VIH 24 mA 24 mA (Note 2) VCC, GND VCC  2.1V 1.65V Max 3.85V Min VCC or GND r 0.1 r 1.0 1.5 75 PA mA mA mA VOLD VOHD VIN 75 20.0 PA V V V V Figure 1, Figure 2 (Note 4)(Note 5) Figure 1, Figure 2 (Note 4)(Note 5) (Note 4)(Note 6) (Note 4)(Note 6) 0.6 1.9 1.2 1.2 2.2 0.8 Note 2: All outputs loaded; thresholds on input associated with output under test. Note 3: Maximum test duration 2.0 ms, one output loaded at a time. Note 4: Plastic DIP package Note 5: Max number of outputs defined as (n). Data inputs are 0V to 3V. One output @ GND. Note 6: Max number of data inputs (n) switching. (n1) inputs switching 0V to 3V (ACTQ). Input-under-test switching: 3V to threshold (VILD), 0V to threshold (VIHD), f 1 MHz. www.fairchildsemi.com 2 74ACTQ02 AC Electrical Characteristics VCC Symbol tPLH tPHL tOSHL, tOSLH Parameter Propagation Delay Data to Output Propagation Delay Data to Output Output to Output Skew (Note 8) (V) (Note 7) 5.0 5.0 5.0 Min 2.0 2.0 TA CL 25qC 50 pF Typ 5.0 5.0 0.5 Max 7.5 7.5 1.0 TA 40qC to 85qC CL 50 pF Max 8.0 8.0 1.0 ns ns ns Units Min 2.0 2.0 Note 7: Voltage Range 5.0 is 5.0V r 0.5V Note 8: Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same device. The specification applies to any outputs switching in the same direction, either HIGH-to-LOW (tOSHL) or LOW-to-HIGH (tOSLH). Parameter guaranteed by design. Capacitance Symbol CIN CPD Parameter Input Capacitance Power Dissipation Capacitance Typ 4.5 75 Units pF pF VCC VCC OPEN 5.0V Conditions 3 www.fairchildsemi.com 74ACTQ02 FACT Noise Characteristics The setup of a noise characteristics measurement is critical to the accuracy and repeatability of the tests. The following is a brief description of the setup used to measure the noise characteristics of FACT. Equipment: Hewlett Packard Model 8180A Word Generator PC-163A Test Fixture Tektronics Model 7854 Oscilloscope Procedure: 1. Verify Test Fixture Loading: Standard Load 50 pF, 500:. 2. Deskew the HFS generator so that no two channels have greater than 150 ps skew between them. This requires that the oscilloscope be deskewed first. It is important to deskew the HFS generator channels before testing. This will ensure that the outputs switch simultaneously. 3. Terminate all inputs and outputs to ensure proper loading of the outputs and that the input levels are at the correct voltage. 4. Set the HFS generator to toggle all but one output at a frequency of 1 MHz. Greater frequencies will increase DUT heating and affect the results of the measurement. VOLP/VOLV and VOHP/VOHV: • Determine the quiet output pin that demonstrates the greatest noise levels. The worst case pin will usually be the furthest from the ground pin. Monitor the output voltages using a 50: coaxial cable plugged into a standard SMB type connector on the test fixture. Do not use an active FET probe. • Measure VOLP and VOLV on the quiet output during the worst case transition for active and enable. VOHP and VOHV on the quiet output during the worst case transition for active and enable. • Verify that the GND reference recorded on the oscilloscope has not drifted to ensure the accuracy and repeatability of the measurements. VILD and VIHD: • Monitor one of the switching outputs using a 50: coaxial cable plugged into a standard SMB type connector on the test fixture. Do not use an active FET probe. • First increase the input LOW voltage level, VIL, until the output begins to oscillate or steps out a min of 2 ns. Oscillation is defined as noise on the output LOW level that exceeds VIL limits, or on output HIGH levels that exceed VIH limits. The input LOW voltage level at which oscillation occurs is defined as VILD. • Next decrease the input HIGH voltage level, VIH, until the output begins to oscillate or steps out a min of 2 ns. Oscillation is defined as noise on the output LOW level that exceeds VIL limits, or on output HIGH levels that exceed VIH limits. The input HIGH voltage level at which oscillation occurs is defined as VIHD. • Verify that the GND reference recorded on the oscilloscope has not drifted to ensure the accuracy and repeatability of the measurements. FIGURE 1. Quiet Output Noise Voltage Waveforms Note 9: VOHV and VOLP are measured with respect to ground reference. Note 10: Input pulses have the following characteristics: f tr 3 ns, tf 3 ns, skew  150 ps. 1 MHz, 5. Set the HFS generator input levels at 0V LOW and 3V HIGH for ACT devices and 0V LOW and 5V HIGH for AC devices. Verify levels with an oscilloscope. FIGURE 2. Simultaneous Switching Test Circuit www.fairchildsemi.com 4 74ACTQ02 Physical Dimensions inches (millimeters) unless otherwise noted 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow Package Number M14A 5 www.fairchildsemi.com 74ACTQ02 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) Pb-Free 14-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide Package Number M14D www.fairchildsemi.com 6 74ACTQ02 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 14-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide Package Number MTC14 7 www.fairchildsemi.com 74ACTQ02 Quad 2-Input NOR Gate Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300" Wide Package Number N14A Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. www.fairchildsemi.com 8 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com