FAN7532MX

FAN7532 Ballast Control IC June 2006 FAN7532 Ballast Control IC Features Floating Channel Designed for Bootstrap Operation to +600V Lower di/dt Gate Driver for Better Noise Immunity Driver Current Capability: 250mA/500mA (Typ.) Low Start-up and Operating Current: 120µA, 6.4mA Under-Voltage Lockout (UVLO) with 1.8V of Hysteresis Programmable Preheat Time and Frequency Programmable Run Frequency Protection from Failure to Strike Lamp Filament Sensing and Protection Automatic Restart for Lamp Exchange High-Accuracy Oscillator 16-Pin SOP Description The FAN7532 provides simple and high-performance electronic ballast control functions. Optimized for an electronic ballast, the FAN7532 requires a minimum board area and reduces component counts. The FAN7532 is intended to drive two power MOSFETs in the classical half-bridge topology with all the features needed to properly drive and control a fluorescent lamp. The FAN7532 has many comprehensive protection features that work through filament failure, failure of a lamp to strike, and automatic restarts. A dedicated timing section in the FAN7532 allows the user to set the necessary parameters to preheat, ignite, and run the lamp properly. Applications General Purpose Ballast IC 16-SOP 1 Ordering Information Part Number FAN7532M FAN7532MX Package 16-SOP Pb-Free Yes Operating Temperature Range Packing Method -25°C ~ 125°C TUBE TAPE & REEL FPSTM is a trademark of Fairchild Semiconductor Corporation. © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FAN7532 Rev. 1.0.2 1 FAN7532 Ballast Control IC Typical Application Circuit D4 L1 1 4 5 DC_400V D1 D12 D13 C1 R1 1 3 R13 D10 NTC D11 1 R4 R2 R12 D2 D3 R5 M1 R8 R9 R6 1 CY1 CY2 C3 C4 8 7 6 5 C2 R11 GND Vcc CX2 LF1 CX1 R3 TNR F1 1 1 2 U1 FAN7527B EA_OUT MULT R7 CS R10 INV C5 1 1 2 OUT 3 4 Idet 1 C6 R14 2 VR1 1 1 AC INPUT DC_400V R51 M50 R52 1 5 L100 C100//C101 R104, R105 R106 C102 D101 R204, R205 R50 M51 C53 1 5 2 R206 C52 R53 R54 2 R55 D50 2 D51 L200 C200//C201 D201 ZD51 C56 R57 C202 DC_400V 16 1 15 13 HO VB U2 12 VS LO PGND R200, R201 D200 2 C57 2 D52 11 4 FAN7532 Vcc GND OLP 10 9 ZD50 C203 2 R202 R100, R101 R102 R103 2 R203 Ignition Fail Detection Circuit C50 C51 2 OVP CPH CT RPH RT 5 6 7 8 D100 C55 2 R56 C54 C103 CPH CT RPH RT Open Lamp Detection Circuit FAN7532 Rev. 00 Figure 1. Application Circuit © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FAN7532 Rev. 1.0.2 2 FAN7532 Ballast Control IC Internal Block Diagram 5V 9V Vsup CPH 5 Bias Current 1.5μA 2.9V 11.8V OLP R S 5V Ict Irt S 1.70V 6.2ICT R 5.15V Latch Q Q Q 15.6V UVLO 1.8V 11 Vcc 10μA Iph - Irt Vz 2.9V 1 2.1 1 HVG Driver VB CT 6 16 HO Frequency Divider & Driving Logic Level Shift Vcc 15 VS 13 LO OLP RT RPH 8 7 Current Source Current Source Irt=Vref/Rt 12 PGND Iph=Vref/Rph Shutdown Signal 9 VCPH TSD 5V 2V OVP OLP OLP : Open Lamp Protection 4 GND 10 OLP 2V FAN7532 Rev. 00 Figure 2. Functional Block Diagram of FAN7532 © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FAN7532 Rev. 1.0.2 3 FAN7532 Ballast Control IC Pin Configuration HO 16 VS 15 NC 14 LO 13 PGND 12 VCC 11 OLP 10 OVP 9 FAN7532 1 VB 2 NC 3 NC 4 GND 5 CPH 6 CT 7 RPH 8 RT FAN7532 Rev. 00 Figure 3. Pin Configuration (Top View) Pin Definitions Pin Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Pin Name VB N.C. N.C. GND CPH CT RPH RT OVP OLP VCC PGND LO N.C. VS HO No Connection No Connection Ground Pin Function Description High-Side Floating Supply Voltage Preheat Time Set Capacitor Oscillator Frequency Set Capacitor Preheat Frequency Set Resistor Oscillator Frequency Set Resistor Over-Voltage Protection, Latch Mode Open Lamp Protection, Only Output Disable Mode Supply Voltage Power Ground Low-Side Gate Driver Output No Connection High-Side Floating Supply Return High-Side Gate Driver Output © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FAN7532 Rev. 1.0.2 4 FAN7532 Ballast Control IC Absolute Maximum Ratings The “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum ratings. The “Recommended Operating Conditions” table defines the conditions for actual device operation. (TA = 25°C, unless otherwise specified.) Symbol ICC VS VB VHO IOH IOL VIN dVS/dt Topr Tstg Pd Rθja Characteristics Supply Current (See Caution Below) High-Side Floating Supply Offset Voltage High-Side Floating Supply Voltage High-Side Floating Output Voltage, HO Drive Output Source Current Drive Output Sink Current CPH, CT, RT, and RPH Pins Input Voltage Allowable Offset Voltage Slew Rate Operating Temperature Range Storage Temperature Range Power Dissipation Thermal Resistance (Junction-to-Air) Min. VB-25 -0.3 VS-0.3 Max. 25 VB+0.3 625 VS+0.3 250 500 Unit mA V mA V V/ns °C W °C/W -0.3 -25 -65 - 6 50 125 150 0.94 100 Caution: You must not supply a low-impedance voltage source to the internal clamping zener diode that is between the GND and the VCC pin of this device. Recommended Operating Conditions Symbol VCC VS VB VHO Supply Voltage High-Side Floating Offset Supply Voltage High-Side Floating Supply Voltage High-Side Floating Output Voltage, HO Parameter Value 11 to VCL 600 VS+11 to VS+20 VS to VB Unit V V V V Temperature Characteristics (-25°C ≤ TA ≤ 125°C) Symbol Δfos (Typ) Parameter Temperature Stability for Operating Frequency (fos) Value 3 Unit % ESD Level Parameter Human Body Model (HBM) Machine Model (MM) Pins GND, CPH, CT, RPH, RT, OVP, OLP, LO VB, VS, HO LO Conditions R = 1.5kΩ, C = 100pF C=200pF Level ±1000 ±250 Unit V Note: ESD immunity for all pins, except for condition noted above, is guaranteed up to 2000V (Human Body Model) and 300V (Machine Model). © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FAN7532 Rev. 1.0.2 5 FAN7532 Ballast Control IC Electrical Characteristics VCC=VBS=14V, TA=25°C unless otherwise specified. Symbol VTH(st) HY(st) VCL IST ICC IDCC Characteristics Start Threshold Voltage UVLO Hysteresis Supply Clamping Voltage Start-Up Supply Current Operating Supply Current Dynamic Operating Supply Current: (ICC+IQBS) CPH Pin Charging Current 1 CPH Pin Charging Current 2 CPH Pin Clamp Voltage Preheating Frequency Preheating Dead Time Operating Frequency Operating Dead Time Differential Threshold Voltage on CT CT Charging Current CT Discharging Current Voltage Stability Low-Side Driver Source Current Low-Side Driver Sink Current High-Side Driver Source Current High-Side Driver Sink Current High/Low-Side Rising Time High/Low-Side Falling Time Offset Supply Leakage Current Quiescent VBS Supply Current Test Condition VCC Increasing ICC = 12mA VCC = 10V Output Not Switching 50kHz, CL = 1nF Min. Typ. Max. Unit 11 0.8 14.7 11.8 1.8 15.6 120 6.4 8.2 12.6 2.8 16.5 180 9.5 10.5 V V V µA mA mA SUPPLY VOLTAGE SECTION OSCILLATOR SECTION ICPHL ICPHH VCLAMP fPH tPD fOSC tOD ΔVCT Ich Idisch Δf/ΔV ILO1 ILO2 IHO1 IHO2 tr tf ILK IQBS VCPH = 2V VCPH = 4V VCPH = 0V, RPH = 20kΩ, CT = 1nF VCPH = 0V, RPH = 20kΩ, CT = 1nF VCPH = Open, RT = 18kΩ, CT = 1nF VCPH = Open, RT = 18kΩ, CT = 1nF VCT = 1.5V VCT = 5.5V 12.7V ≤ VCC ≤ VCL VLO = VCC VLO = GND VHO = VB VHO = VS CL = 1nF CL = 1nF VB = VS = 600V 1 7.7 5.1 75 0.75 48 1.5 3 400 1.95 200 400 200 400 10 1.8 0.6 1.5 10 5.65 85 1.20 50 2 3.45 460 2.4 250 500 250 500 90 40 48 2 0.92 0.35 150 2 12.3 6.2 95 1.55 52 2.3 4 510 2.8 3 150 100 10 90 2.3 1.3 0.45 µA µA V kHz µs kHz µs V µA mA % mA mA mA mA ns ns µA µA V V mA °C OUTPUT SECTION HIGH-VOLTAGE SECTION PROTECTION SECTION Vth_com OVP/OLP Comparator Threshold Voltage Vhy_com OLP Comparator Hysteresis Voltage Ilatch TSD Latch Mode Quiescent Current Thermal Shutdown Junction Temperature © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FAN7532 Rev. 1.0.2 6 FAN7532 Ballast Control IC Typical Performance Characteristics These characteristic graphs are normalized at TA= 25°C. 95 53 52 90 fPH [kHz] 51 85 FOSC [kHz] -20 0 20 40 60 80 100 120 50 49 80 48 75 -40 47 -40 -20 0 20 40 60 80 100 120 Ambient Temperature [°C] Ambient Temperature [°C] Figure 4. Preheating Frequency vs. Temp. Figure 5. Operating Frequency vs. Temp. 180 160 80 70 140 120 100 80 60 40 30 20 0 -40 20 -40 60 IQBS [µA] IST [µA] 50 40 -20 0 20 40 60 80 100 120 -20 0 20 40 60 80 100 120 Ambient Temperature [°C] Ambient Temperature [°C] Figure 6. Turn-off Propagation Delay vs. Temp. Figure 7. Dynamic Operating Current vs. Temp. 8.0 7.5 9.0 8.5 7.0 8.0 6.5 6.0 5.5 5.0 6.5 4.5 4.0 -40 6.0 -40 IDCC [mA] -20 0 20 40 60 80 100 120 ICC [mA] 7.5 7.0 -20 0 20 40 60 80 100 120 Ambient Temperature [°C] Ambient Temperature [°C] Figure 8. Dynamic Operating Current vs. Temp. Figure 9. Dynamic Operating Current vs. Temp. © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FAN7532 Rev. 1.0.2 7 FAN7532 Ballast Control IC Typical Performance Characteristics (Continued) These characteristic graphs are normalized at TA= 25°C. 500 2.4 400 ILATCH [µA] 300 VTH_OVP [V] -20 0 20 40 60 80 100 120 2.2 2.0 200 1.8 100 1.6 -40 -40 -20 0 20 40 60 80 100 120 Ambient Temperature [°C] Ambient Temperature [°C] Figure 10. Latch Mode Current vs. Temp. Figure 11. OVP Detection Voltage vs. Temp. 140 2.4 130 120 Rph=20kΩ Rph=10kΩ Frequency [kHz] -20 0 20 40 60 80 100 120 VTH_OLP [V] 2.2 110 100 90 80 70 2.0 1.8 60 50 1.6 -40 0 1 2 3 4 5 6 Ambient Temperature [°C] Vcph [V] Figure 12. OLP Detection Voltage vs. Temp. Figure 13. Preheating Frequency vs. Rph 160 140 Ct = 1nF Ct = 470pF Frequency [kHz] 120 100 80 60 40 20 0 5 10 15 20 25 30 35 40 45 Rt [kΩ] Figure 14. Run Frequency vs. Rt and Ct © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FAN7532 Rev. 1.0.2 8 FAN7532 Ballast Control IC Application Information 1. Start-up Circuit The start-up current is supplied to the IC through the start-up resistor (Rst). To reduce the power dissipation in Rst, Rst is connected to the full-wave, rectified output voltage. The size of Rst can be determined by equations (1) and (2). DC 400V 3. Oscillator The gate drive output frequency is half that of the triangular waveform on timing capacitor (CT) at pin #6. In normal operating mode, the timing capacitor charging current is 4•Irt (=Vref/RT). The discharging current is 6.2 times the charging current. During the charging period of the timing capacitor (CT), the MOSFET alternatively turns on. During the discharging period of the timing capacitor (CT), both MOSFETs are off. Discharging Period (ΔTDIS) Rectifier Output M1 G1 Charging Period (ΔTCH) Vref ICH ICH IDIS=6.2∗ICH Rst D2 Vcc CQ VCT 3.45V CT IDIS Cs ZD1 D1 LO G2 M2 HO FAN7532 Rev. 00 Dead Time FAN7532 Rev. 00 Figure 15. Start-up Circuit Vin(ac) × 2 -Vth(st).max Ist,max 85 × 2 -12.4 0.18 × 10 -3 =599 [kΩ] Figure 16. CT & Output Waveforms (1) The FAN7532 has three operating modes according to VCPH, as shown in Figure 17. Vcc Rst = = Rst = (Vin(ac,max) × 2 -Vcc )2 Rst Vth(st) ≤ 0.5 [W] (2) t Rst ≥ 2 × (Vin (ac,max) × 2 − Vcc )2 ≥ 260 [k Ω] VCPH ICPHL=1.5mA ICPHH=10mA ∴ 260[k Ω] ≤ Rst ≤ 599[k Ω] 5V 2.9V t f fpre fpre fign frun The size of supply capacitor (Cs) is normally determined by the start-up time and the operating current which is built up by the auxiliary operating current source. The turn-off snubber capacitor (CQ) and two diodes (D1, D2) constitute the auxiliary operating current source for the IC. The charging current through the CQ flows into the IC and charges the supply capacitor. If the size of CQ is increased, the VCC voltage on the Cs is also increased. frun 2. Under-Voltage Lockout (UVLO) The UVLO mode of the FAN7532 is designed to maintain an ultra low supply current of less than 120µA, and to guarantee that the IC is fully functional before two output drivers are activated. preheating tph ignition tsw run t FAN7532 Rev. 00 Figure 17. Operating Modes © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FAN7532 Rev. 1.0.2 9 FAN7532 Ballast Control IC 0V ≤ VCPH ≤ 2.9V , ;Preheating Frequency 5. Ignition Mode The ignition mode is defined as the IC’s internal status when VCPH is approximately between 2.9V and 5V. During ignition, the operating frequency is decreased to a pre-determined value. At the same time, a very highvoltage for igniting the lamp is established across the lamp. When the VCPH exceeds 2.9V, the FAN7532 enters the ignition mode. Once VCPH exceeds 5V, the device enters the run mode described in the following section. In the ignition period, the internal 10mA current source charges the external preheating timing capacitor (CPH) to increase noise immunity with the sharp slope of the VCPH. The ignition time is determined by the CPH and internal 10mA current source ( ΔTign = CPH × ΔIVCPH ). In this CPH mode, the switching frequency is determined by CT, RPH, and RT. Therefore, the charging and discharging currents change according to VCPH and are determined by equation (7). ICT = IRT + ICT = IRT + IPH − IRT ( 5V − 2.9V ) = IPH ( 5V − 2.9V ) ;Ignition Frequency IPH − IRT 2.9V ≤ VCPH ≤ 5V , ICT = IRT + VCPH ≥ 5V ICT = IRT , ( 5V − 2.9V ) ( 5V − VCPH ) ;Run Frequency 4. Preheating Mode The preheating mode is defined as the IC’s internal status when the VCPH is between 0V and 2.9V. During preheating, the current that flows through the ballast circuit heats the lamp filaments. This is necessary for maximizing lamp life and reducing the required ignition voltage. When the VCC exceeds the UVLO high threshold, the preheating time set-up capacitor, CPH, starts being charged by the internal 1.5µA current source until the VCPH reaches 2.9V. Until the VCPH reaches 2.9V, the switching frequency throughout the preheating mode is determined by CT and RPH. The preheating time is determined by the CPH and the 1.5µA current source. Therefore, the preheating time is determined by equation (3): t pre = CPH × VCPH Icharging ( 5V − 2.9V ) IPH − IRT ( 5V − VCPH ) (7) 6. Run Mode After the lamp has successfully ignited, the FAN7532 enters run mode. The run mode is defined as the IC’s internal status when VCPH is higher than 5V. In this mode, the lamp is being driven with a normal power level after the lamp is discharged. The run mode switching frequency is determined by the timing resistor RT and the timing capacitor CT. When the VCPH exceeds 5V, the protection-masking mode is disabled and the IC can enter the protection mode. The running frequency is determined by the amount of charging and discharging current to CT capacitor. The charging and discharging currents during preheating mode are decided by the equation (8): Irun _ ch = 2 × Vref RT (3) The preheating frequency is determined by the amount of charging and discharging current to the CT capacitor. The charging and discharging current during preheating mode is decided by equation (4): I pre _ ch = 4 × I pre _ disch = 4 × Vref RPH (4) ( 6.25 × Vref ) RPH , Vref = 4V (Constant ) (8) The charging and discharging time of the CT capacitor during preheating mode is decided by equation (5): t pre _ ch = CT × t pre _ disch = CT × dVCT I pre _ disch dVCT I pre _ ch Irun _ disch = 2 × ( 6.25 × Vref ) RT , Vref=4V (Constant) dVCT Irun _ ch (5) trun _ ch = CT × trun _ disch = CT × (9) , dVCT=3.45V (Constant) dVCT , dVCT=3.45V (Constant) Irun _ disch Finally, the FAN7532’s preheating frequency in the preheating period is determined by equation (6): fpre = 2 × t pre _ ch + t pre _ disch ( 1 Finally, the preheating frequency in the preheating period using the FAN7532 is determined by the equation (10): frun = 2 × trun _ ch + trun _ disch ) (6) ( 1 ) (10) © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FAN7532 Rev. 1.0.2 10 FAN7532 Ballast Control IC 7. Protection Modes The FAN7532 has two types of protection modes. 1) Over-Voltage Protection (OVP) Mode The OVP pin is normally connected to the external components that detect lamp voltage between a lamp’s cathodes. This voltage is always maintained under 2V in normal operation. If the lamp enters the end-lamp-life or abnormal condition, the lamp does not turn-on even if there is enough voltage supplied between two cathodes. Normally, this condition means that one of the cathodes is broken, deactivated, or the lamp is deeply blackened around the cathodes. In this state, the ballast constantly generates very high voltage between two cathodes to ignite according to a specific procedure in the control IC. When the voltage of OVP pin exceeds 2V, the IC instantly enters the protection mode. To exit this mode, the VCC must be recycled below the UVLO low threshold. VCC 15.6V VUVLO+ VUVLO- VCPH 5V 2.9V FREQ fPH fOSC OVP Ignition fail VLAMP Ignition fail level Preheating Ignition Latched shutdown UVLO Preheating Ignition Run Latched shutdown mode is removed after VCC goes down to the UVLO- FAN7532 Rev. 00 Figure 18. Timing Diagram (OVP Mode) © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FAN7532 Rev. 1.0.2 11 FAN7532 Ballast Control IC 2) Open Lamp Protection (OLP) Mode After the lamp has successfully ignited, the FAN7532 enters run mode. In this mode, if one of the cathodes isn’t correctly connected to the ballast, the ballast stops operation for safety until the lamp is changed and a new one is connected between the lamp and the ballast. As soon as the voltage of OLP pin exceeds 2V, the IC 15.6V VUVLO+ VUVLO- enters the protection mode. However, the FAN7532 outputs are only disabled in this mode. To exit protection mode, the lamp must be replaced or correctly connected to the ballast. VCPH 5V 2.9V Reset when open lamp Reset when open lamp FREQ fPH fOSC OLP Open lamp Open lamp Only gate driver is disabled Only gate driver is disabled VLAMP Run Open Lamp Preheating Ignition Run Open Lamp Preheating Ignition Run FAN7532 Rev. 00 Figure 19. Timing Diagram (OLP Mode) 8. PCB Layout Guides Component selection and placement on the PCB is very important when using power control ICs. Bypass the VCC to GND as close to the IC terminals as possible with a low ESR/ESL capacitor, as shown in Figure 20. This bypassed capacitor can reduce the noise from the power supply parts, such as a startup resistor and a charge pump. The GND lead should be directly connected to the low-side power MOSFET using an individual PCB trace. In addition, the ground return path of the timing components (CPH, CT, RPH, RT) and VCC decoupling capacitor should be connected directly to the IC GND lead and not via separate traces or jumpers to other ground traces on the board. These connection techniques prevent high-current ground loops from interfering with sensitive timing component operations and allow the entire control circuit to reduce common-mode noise due to output switching. Figure 20. PCB Layout © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FAN7532 Rev. 1.0.2 12 FAN7532 Ballast Control IC Components List (for Wide-Range 32W× 2 Lamps Application) Part number F1 CX1 CX2 CY1, CY2 TNR NTC D10, D11, D12, D13 LF1 R1, R2, R8 R3 R4 R5 R6 R7 R9 R10 R11 R12 R13 R14 VR1 C1 C2 C3 C4 C5 C6 L1 D1, D4 D2 D3 M1 U1 Value INPUT PART Note Fuse Box-Cap Box-Cap Y-Cap 471 10D09 1N4004 PFC PART Manufacturer 250V, 3A 47nF, 275Vac 150nF, 275Vac 2200pF, 3000V 470V 10Ω 400V, 1A 45mH 910kΩ 22kΩ 22kΩ 10Ω 22kΩ 0.47Ω 100kΩ 2.2kΩ 220kΩ 150kΩ 4.7Ω 0Ω 10kΩ 0.22µF, 630V 47µF, 450V 10µF, 50V 105 102 105 0.9mH (80T:6T) 600V, 1A, Ultrafast Schottky Diode Small Signal Diode 500V, 6A, Power MOSFET PFC IC Fairchild Semiconductor Ceramic, 1206 Ceramic, 1206 Ceramic, 1206 Ceramic, 1206 Ceramic, 1206 1W Ceramic, 1206 Ceramic, 1206 1W 1W Ceramic, 1206 Ceramic, 1206 Variable Resistor Mylar-Cap Electrolytic Electrolytic Ceramic, 0805 Ceramic, 0805 Ceramic, 0805 EI2820 UF4005 MBR0540 FDLL4148 FQP6N50C, FQPF6N50C FAN7527B Fairchild Semiconductor Fairchild Semiconductor Fairchild Semiconductor Fairchild Semiconductor Fairchild Semiconductor © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FAN7532 Rev. 1.0.2 13 FAN7532 Ballast Control IC Components List (Continued) Part number R50 R51, R53 R52, R54 R55 R56, R57 RPH RT R100, R104, R200, R204 R101, R105, R201, R205 R102, R202 R103, R203 R106, R206 C50 C51 C52 C53 C54, C55, C56, C57,C103,C203 CT CPH C100, C101, C200, C201 C102, C202 L100, L200 M50, M51 ZD50,ZD51 D50,D51,D52 D100, D101, D200, D201 U2 Value BALLAST PART Note 1W Ceramic, 1206 Ceramic, 1206 1W Ceramic, 0805 Ceramic, 1206, 1% Ceramic, 1206, 1% Ceramic, 1206 Ceramic, 1206 Ceramic, 1206 Ceramic, 1206 Ceramic, 1206 Electrolytic Ceramic, 0805 Ceramic, 1206 Miller-Cap Ceramic, 0805 Ceramic, 0805, 5% Ceramic, 0805 Mylar-Cap Mylar-Cap EE2820 FQP5N50C, FQPF5N50C 1N5245 UF4005 FDLL4148 FAN7532 Manufacturer 390kΩ 39Ω 47kΩ 5.6Ω 68kΩ 27kΩ 18kΩ 910kΩ 300kΩ 5.1kΩ 68kΩ 30kΩ 10µF, 50V 105 104 681, 630V 104 1nF 680nF 6.8nF, 630V 3.3nF, 1000V 3.2mH (120T) 500V, 5A, Power MOSFET Zener Diode 600V,1A,Ultrafast Small Signal Diode Ballast IC Fairchild Semiconductor Fairchild Semiconductor Fairchild Semiconductor Fairchild Semiconductor Fairchild Semiconductor © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FAN7532 Rev. 1.0.2 14 FAN7532 Ballast Control IC Package Dimensions 16-SOP Dimensions in millimeters MIN 1.55 ±0.10 0.061 ±0.004 #1 #16 10.30 MAX 0.405 9.90 ±0.20 0.39 ±0.008 #8 #9 6.00 ±0.30 0.236 ±0.012 3.95 ±0.20 0.156 ±0.008 1.80 MAX 0.071 +0.004 0.008 -0.002 0.20 5.72 0.225 0.70 ±0.20 0.0275 ±0.008 0~ 8° January 2001, Rev. A © 2006 Fairchild Semiconductor Corporation MAX0.10 MAX0.004 +0.10 -0.05 1.27 0.050 www.fairchildsemi.com FAN7532 Rev. 1.0.2 15 +0.004 0.016 -0.002 0.406 +0.10 -0.05 ( 0.51 ) 0.020 0.05 0.002 FAN7532 Ballast Control IC TRADEMARKS The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks. ACEx™ FAST® ActiveArray™ FASTr™ Bottomless™ FPS™ Build it Now™ FRFET™ CoolFET™ GlobalOptoisolator™ CROSSVOLT™ GTO™ HiSeC™ DOME™ I2C™ EcoSPARK™ 2 i-Lo™ E CMOS™ EnSigna™ ImpliedDisconnect™ FACT™ IntelliMAX™ FACT Quiet Series™ Across the board. Around the world.™ The Power Franchise® Programmable Active Droop™ ISOPLANAR™ LittleFET™ MICROCOUPLER™ MicroFET™ MicroPak™ MICROWIRE™ MSX™ MSXPro™ OCX™ OCXPro™ OPTOLOGIC® OPTOPLANAR™ PACMAN™ POP™ Power247™ PowerEdge™ PowerSaver™ PowerTrench® QFET® QS™ QT Optoelectronics™ Quiet Series™ RapidConfigure™ RapidConnect™ µSerDes™ ScalarPump™ SILENT SWITCHER® SMART START™ SPM™ Stealth™ SuperFET™ SuperSOT™-3 SuperSOT™-6 SuperSOT™-8 SyncFET™ TCM™ TinyLogic® TINYOPTO™ TruTranslation™ UHC™ UniFET™ UltraFET® VCX™ Wire™ DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Advance Information Product Status Formative or In Design Definition This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. This datasheet contains preliminary data, and supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. This datasheet contains specifications on a product that has been discontinued by Fairchild semiconductor. The datasheet is printed for reference information only. Preliminary First Production No Identification Needed Full Production Obsolete Not In Production Rev. I19 © 2006 Fairchild Semiconductor Corporation www.fairchildsemi.com FAN7532 Rev. 1.0.2 16