SG6846A

SG6846A — Highly Integrated Green-Mode PWM Controller September 2008 SG6846A Highly Integrated Green-Mode PWM Controller Features Low Startup Current: 8µA Low Operating Current: 3.7mA Peak-Current Mode of Operation with Cycle-byCycle Current Limiting PWM Frequency Continuously Decreasing with Burst Mode at Light Loads VDD Over-Voltage Protection (OVP) AC Input Brownout Protection with Hysteresis Constant Output Power Limit (Full AC Input Range) Internal Latch Circuit for OVP, OTP, and OCP Two-level OCP Delay: 1600ms Output Short-Circuited Delay Time: 100ms Programmable PWM Frequency with Frequency Hopping OCP Threshold is Half Peak Current Limit Feedback Open-loop Protection with 1700ms Delay Built-in Soft-Start Description The SG6846A is especially designed for SMPS with surge-current output, incorporated with a two-level OCP function. Besides the cycle-by-cycle current limiting, if the switching current is higher than two thirds the peakcurrent threshold for 1700ms, over-current protection is activated such that the SG6846A is latched off. If the switching current is higher than two thirds of the peak-current threshold for 100ms, and the voltage on the VDD is still higher than VDD-OFF + 1V, the PWM pulses are latched off immediately once the VDD voltage is lower than VDD-OFF + 1V. This is useful when an output short circuit occurs. SG6846A also integrates a frequency-hopping function internally to reduce EMI emission of a power supply with minimum line filters. Its built-in synchronized slope compensation provides proprietary internal compensation for constant output power limit over universal AC input range. Also, the gate output is clamped at 18V to protect the external MOSFET from over-voltage damage. Internal soft-start is built-in to soften the stress on the MOSFET and startup current during power on period. Other protection functions include AC input brownout protection with hysteresis, VDD over-voltage protection, and over-temperature protection. For over-temperature protection, an external NTC thermistor can be applied to sense the ambient temperature. When OCP, VDD OVP, or OTP is activated, an internal latch circuit latches off the controller. The PWM pulses stay latched off until the power supply is disconnected from the mains outlet. SG6846A controller is available in 8-pin SOP package. Applications General-purpose switch-mode power supplies and flyback power converters, including: Power Adapters Open-frame SMPS SMPS with Surge-current Output, such as for Printers, Scanners, Motor Drivers Ordering Information Part Number SG6846ALSY SG6846ACSY SG6846ALSZ Operating Temperature Range -40 to +105°C -40 to +105°C -40 to +105°C OCP Latch Yes No Yes Eco Status Green Green RoHS Package 8-Pin Small Outline Package (SOP) 8-Pin Small Outline Package (SOP) 8-Pin Small Outline Package (SOP) Packing Method Tape & Reel Tape & Reel Tape & Reel For Fairchild’s definition of “green” Eco Status, please visit: http://www.fairchildsemi.com/company/green/rohs_green.html. © 2008 Fairchild Semiconductor Corporation SG6846A • Rev. 1.1.4 www.fairchildsemi.com SG6846A — Highly Integrated Green-Mode PWM Controller Typical Application Figure 1. Typical Application Block Diagram Figure 2. Block Diagram © 2008 Fairchild Semiconductor Corporation SG6846A • Rev. 1.1.4 www.fairchildsemi.com 2 SG6846A — Highly Integrated Green-Mode PWM Controller Marking Information SG6846AFTP XXXXXXXXYWWV F: L = OCP Latch T: S = SOP P: Z = Lead Free + ROHS Compatible Null = regular package XXXXXXXX: Wafer Lot Y: Year; WW: Week V: Assembly Location Figure 3. Top Mark 1 : Fairchild logo Z: Plant Code X: Year Code Y: Week Code TT: Die Run Code F: L =OCP Latch, C = OCP auto-recovery T: Package type, S = SOP P: Y =Green Package M: Manufacturing flow code Figure 4. Top Mark 2 *The “Top Mark 2” is the updated mark. * © 2008 Fairchild Semiconductor Corporation SG6846A • Rev. 1.1.4 www.fairchildsemi.com 3 SG6846A — Highly Integrated Green-Mode PWM Controller Pin Configuration Figure 5. Pin Configuration Pin Definitions Pin # 1 2 Name GND FB Function Ground Feedback Line-voltage Detection Reference Setting Temperature Detection Description Ground. The signal from the external compensation circuit is fed into this pin. The PWM duty cycle is determined in response to the signal from this pin and the currentsense signal from pin 6. Line-voltage detection is used for brownout protection with hysteresis. Constant output power limit over universal AC input range is achieved using this pin. Add a low-pass filter to filter out line ripple on the bulk capacitor. A resistor from the RI pin to ground generates a reference current source that determines the switching frequency. Increasing the resistance reduces the switching frequency. A 26kΩ resistor results in a 65kHz switching frequency. For over-temperature protection, an external NTC thermistor is connected from this pin to the GND pin. The impedance of the NTC decreases at high temperatures. Once the voltage of the RT pin drops below a threshold, PWM output is disabled. The sensed voltage is used for peak-current-mode control and cycle-by-cycle current limiting. If the switching current is higher than OCP threshold and lasts for 1700ms, SG6846A turns off immediately. This two-level OCP feature is especially suitable for SMPS with surge current output. If an open-circuit failure occurs in the feedback loop, the internal protection circuit disables PWM output as long as VDD exceeds a threshold. The totem-pole output driver for the power MOSFET; internally clamped below 18V. 3 VIN 4 RI 5 RT 6 SENSE Current Sense 7 8 VDD GATE Power Supply Driver Output © 2008 Fairchild Semiconductor Corporation SG6846A • Rev. 1.1.4 www.fairchildsemi.com 4 SG6846A — Highly Integrated Green-Mode PWM Controller Absolute Maximum Ratings Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. All voltage values, except differential voltages, are given with respect to GND pin. Symbol VDD VL PD ΘJC TJ TSTG TL ESD Supply Voltage Parameter Input Voltage to FB, SENSE, VIN, RT, RI Pins Power Dissipation at TAVN 62 ±3.7 65 ±4.2 130 ±8.4 47.0 ±2.90 4.4 11.5 22.5 2.1 4.2 1.6 1.45 85 68 ±4.7 136 ±9.4 49.2 ±3.26 4.9 12.8 25.0 2.3 4.7 1.8 1.62 kHz fOSC,MAX Maximum PWM Frequency Center Frequency Jitter Range RI = 13kΩ, VFB>VN 124 ±7.4 kHz fOSC,MIN thop-1 thop-3 fOSC-G VFB-N Center Minimum PWM Frequency Frequency Jitter Range Jitter Period Green-Mode Minimum Frequency Pin, FB voltage FB Pin Frequency Reduction Threshold Jitter Range FB Voltage at fOSC-G Pin, FB voltage Jitter Range RI = 36kΩ, VFB>VN RI = 26kΩ, VFB ≥ VN RI = 26kΩ, VFB = VG RI = 26kΩ RI = 26kΩ, VFB = VN 44.8 ±2.54 3.9 10.2 18.0 1.9 3.7 1.4 1.27 kHz ms kHz V KHz V KHz Hz/mV VFB-G SG fDV fDT RI = 26kΩ, VFB = VG RI = 26kΩ VDD = 11.5V to 20V TA = -30 to 85°C Slope for Green-Mode Modulation Frequency Variation vs. VDD Deviation Frequency Variation vs. Temperature Deviation 5 1.5 5.0 % % Continued on following page… © 2008 Fairchild Semiconductor Corporation SG6846A • Rev. 1.1.4 www.fairchildsemi.com 7 SG6846A — Highly Integrated Green-Mode PWM Controller Frequency +4.2 KHz 65KHz -4.2 KHz PW M Frequency +1. 45KHz 22 .5KHz -1. 45KHz V FB-G V FB-N Figure 7. PWM Frequency VFB Electrical Characteristics (Continued) VDD = 15V and TA = 25°C unless otherwise noted. Symbol PWM Output Section DCYMAX VOL VOH tR tF VCLAMP Parameter Test Condition Min. Typ. Max. Unit Maximum Duty Cycle Output Voltage Low Output Voltage High Rising Time Falling Time Gate Output Clamping Voltage (1) 80 VDD = 15V, IO = 50mA VDD = 12V, IO = 50mA GATE = 1nF GATE = 1nF VDD = 20V 8 85 90 1.5 % V V 350 50 18 ns ns V Over-Temperature Protection (OTP) Section IRT VRTTH tDOTP-LATCH RRT-OFF Output Current of RT Pin Threshold Voltage for OTP RI = 26kΩ 64 1.015 70 1.065 100 76 1.115 µA V ms Over-Temperature Latch-off Debounce Equivalent Impedance of RT for OTP (1) RI = 26kΩ RI = 26kΩ 14 15 16 kΩ RI Section RINOR RIMAX RIMIN RI Operating Range Maximum RI Value for Protection Minimum RI Value for Protection 13 10 6 36 kΩ MΩ kΩ (1) Note: 1. The relationship between RRT-OFF and RI is: RRT -OFF = VOTP-LATCH-OFF / IRT = VRT / (70 μA × 26 / RI (KΩ )) © 2008 Fairchild Semiconductor Corporation SG6846A • Rev. 1.1.4 www.fairchildsemi.com 8 SG6846A — Highly Integrated Green-Mode PWM Controller Typical Performance Characteristics 20 18 11.5 11.1 VDD-ON (V) 16 14 12 10 -40 -25 -10 5 20 35 50 65 80 95 110 125 VDD-OFF (V) 10.7 10.3 9.9 9.5 -40 -25 -10 5 20 35 50 65 80 95 110 125 Temperature (℃) Figure 8. Turn-on Threshold Voltage (VDD-ON) vs. Temperature Temperature (℃) Figure 9. Turn-off Threshold Voltage (VDD-OFF) vs. Temperature 30.0 10 IDD-ST (µA) IDD-ST (µA) 26.8 23.6 20.4 17.2 14.0 -40 -25 -10 5 20 35 50 65 80 95 110 125 8 6 4 2 0 10 11 12 13 14 15 16 Temperature (℃) Figure 10. Startup Current (IDD-ST) vs. Temperature VDD (V) Figure 11. Startup Current vs. VDD Voltage 2.5 1.00 VIN-OFF (V) VIN-ON (V) 2.0 1.5 1.0 0.5 0.0 -40 -24 -7 10 26 43 59 76 92 109 125 0.98 0.96 0.94 0.92 0.90 -40 -25 -10 5 20 35 50 65 80 95 11 12 05 Temperature (℃) Temperature (℃ ) Figure 13. PWM Turn-on Threshold Voltage (VIN-ON) vs. Temperature Figure 12. PWM Turn-off Threshold Voltage (VIN-OFF) vs. Temperature © 2008 Fairchild Semiconductor Corporation SG6846A • Rev. 1.1.4 www.fairchildsemi.com 9 SG6846A — Highly Integrated Green-Mode PWM Controller Typical Performance Characteristics (Continued) 85 80 FOSC (kHz) 75 70 65 60 -40 -25 -10 5 20 35 50 65 80 95 110 125 PWM Frequency (kHz) 70 56 42 28 14 0 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 Temperature (°C) Figure 14. Normal PWM Frequency (fOSC) vs. Temperature VFB (V) Figure 15. PWM Frequency vs. FB Voltage 0.90 0.85 VTH-O (V) VTH-P (V) 0.80 0.75 0.70 0.65 0.60 0.7 0.9 1.1 1.3 1.5 1.7 1.9 2.1 2.3 2.5 2.7 2.9 3.1 3.3 0.90 0.82 0.74 0.66 0.58 0.50 0.7 0.9 1.1 1.3 1.5 1.7 1.9 2.1 2.3 2.5 2.7 2.9 3.1 3.3 VIN ( V ) VIN (V) Figure 16. Current-Limit Threshold vs. VIN Voltage Figure 17. 2/3 Current-Limit Threshold vs. VIN Voltage 71.0 70.5 70.0 69.5 69.0 68.5 -40 -25 -10 5 20 35 50 65 80 95 110 125 1.4 1.2 VRTTH (V) IRT (µA) 1.0 0.8 0.6 0.4 -40 -25 -10 5 20 35 50 65 80 95 110 125 Temperature (℃) Temperature (℃) Figure 19. FB Output High Voltage (VRTTH) vs. Temperature Figure 18. Output Current of RT Pin (IRT) vs. Temperature © 2008 Fairchild Semiconductor Corporation SG6846A • Rev. 1.1.4 www.fairchildsemi.com 10 SG6846A — Highly Integrated Green-Mode PWM Controller Operation Description Startup Operation The turn-on/turn-off thresholds are fixed internally at 16.5V and 10.5V. To enable the SG6846A during startup, the hold-up capacitor must first be charged to 16.5V through the startup resistor. The hold-up capacitor continues to supply VDD before energy can be delivered from the auxiliary winding of the main transformer. The VDD must not drop below 10.5V during this startup process. This UVLO hysteresis window ensures that the hold-up capacitor can adequately supply VDD during startup. The typical startup current is only 8µA, which allows a high-resistance, low-wattage startup resistor to be used. For constant output power limit over a universal inputvoltage range, the peak-current threshold is adjusted by the voltage of the VIN pin. Since the VIN pin is connected to the rectified AC input line voltage through the resistive divider, a higher line voltage generates a higher VIN voltage. The threshold voltage decreases as the VIN increases, making the maximum output power at high line input voltage equal to that at low line input. The value of R-C network should not be so large it affects the power limit (shown in Figure 20). R and C should put on less than 300Ω and 1000pF, respectively, to minimize power loss. A 1.5MΩ/0.25W startup resistor and a 10µF/25V VDD hold-up capacitor are sufficient for a universal input range. The required operating current has been reduced to 3.7mA, which enables higher efficiency and reduces the VDD hold-up capacitance requirement. If an open-circuit or short-circuit to ground occurs at the RI pin, the internal protection circuit immediately shuts down the controller. Two-level Over-current Protection (OCP) The cycle-by-cycle current limiting shuts down the PWM immediately when the switching current is over the peak-current threshold. Additionally, when the switching current is higher than the over-current threshold, the internal counter counts down. When the total accumulated counting time is more than ~1600ms (RI = 26kΩ), the controller is latched off and the internal counter counts up. When the switching current is lower than the over-current threshold, the internal counter counts down. When the total accumulated counting time is more than ~1600ms (RI = 26kΩ), the controller is latched off. This two-level OCP protection and up/down counter are especially designed for SMPS with surge current output, such as those for printers, scanners, and motor drivers. Constant Output Power Limit For constant output power limit over universal inputvoltage range, the peak-current threshold is adjusted by the voltage of the VIN pin. Since the VIN pin is connected to the rectified AC input line voltage through the resistive divider, a higher line voltage generates a higher VIN voltage. The threshold voltage decreases as VIN increases, making the maximum output power at high-line input voltage equal to that at low-line input. Green-Mode Operation The proprietary green-mode function provides off-time modulation to continuously decrease the switching frequency under light-load conditions. Maximum on-time is limited to provide protection against abnormal conditions. To further reduce power consumption under zero-load condition, the PWM oscillator is completely turned off and the power supply enters burst-mode. This green mode dramatically reduces power consumption under light-load and zero-load conditions. Power supplies using SG6846A can meet restrictive international regulations regarding standby power consumption. Brownout Protection Since the VIN pin is connected through a resistive divider to the rectified AC input line voltage, it can also be used for brownout protection. If the VIN voltage is less than 0.7V, the PWM output is shut off. If the VIN is over 0.9V, the PWM output is turned on again. The hysteresis window for on/off is ~0.2V. VDD Over-voltage Protection (OVP) VDD over-voltage protection is built in to prevent damage. If VDD is over 23.6V, SG6846A is latched off. Over-Temperature Protection (OTP) Oscillator Operation A resistor connected from the RI pin to GND generates a reference current source, inside the SG6846A, used to determine the PWM frequency. Increasing the resistance decreases the amplitude of the current source and reduces the PWM frequency. Using a 26kΩ resistor results in a corresponding 65kHz switching frequency. The relationship between RI and the switching frequency is: An external NTC thermistor can be connected from the RT pin to GND. The impedance of the NTC decreases at high temperatures. When the voltage of the RT pin drops below 1.05V, the SG6846A is turned off. For protection-mode options, see Ordering Information. fPWM(kHz) = 1690 R I (kΩ ) (2) © 2008 Fairchild Semiconductor Corporation SG6846A • Rev. 1.1.4 www.fairchildsemi.com 11 SG6846A — Highly Integrated Green-Mode PWM Controller Operation Description (Continued) Noise Immunity Noise from the current sense or the control signal may cause significant pulse-width jitter, particularly in continuous-conduction mode. Slope compensation helps alleviate this problem. Good placement and layout practices should be followed. Avoid long PCB traces and component leads. Compensation and filter components should be located near the SG6846A. Figure 20. Current Sense R-C Filter © 2008 Fairchild Semiconductor Corporation SG6846A • Rev. 1.1.4 www.fairchildsemi.com 12 SG6846A — Highly Integrated Green-Mode PWM Controller Reference Circuit P1 F1 RT1 t 2 2 4 3 1 CY1 CX1LF2 BD1 1 2 5 R16 D4 TX1 13 3 6 + 1 2 2 VZ1 P2 P7 1 3 4 2 2 LF1 CY2 R8 3 1 C2 R12 C4 D2 1 2 C16 + 1 + C12 2 CX2 4 P32V P32V L1 + 32V C13 32V 10 1 7 1 3 9 R1 R2 R3 2 R9 D1 1 + 21 2 + C11 R17 P16V P16V L2 2 2 11 1 2 3 L4 D3 12 2 1 + C17 + D5 1 C14 2 1 R4 1 C3 C5 1 R11 + 16V 16V C15 U1 1 GND FB VIN RI GATE VDD SENSE RT 8 7 6 5 2 R13 R6 R10 NTC1 C6 Q1 1 2 FB 2 2 3 L3 R14 P16V C1 1 + R5 4 R7 1 3 P16V R15 4 1 FB FB P16V 1 P32V C7 3 C9 U2 2 K R P16V R18 R19 R21 P32V R20 U3 A Figure 21. Application Circuit for 32V / 16V Output BOM Part No. R1, R2, R3, R4 R8, R9 R5 R15 R13 R18 R21 R7 R6 R19 R14 R16, R17 R11 R12 R20 R22 Value 470KΩ +/-5% S1MΩ +/-1% 16K2Ω +/-1% 1K5Ω +/-5% 10Ω +/-5% 4K7Ω +/-5% 15KΩ +/-1% 27KΩ +/-5% 330Ω +/-1% 102KΩ +/-1% 0Ω22 +/-5% 1W 20Ω +/-5% 20KΩ +/-5% 100KΩ +/-5% 887KΩ +/-1% 10KΩ +/-1% Part No. C4 C10,C11 C6,C7 C9 C14,C17 C15 C13,C16 C2 C1 C3 CX1 C8 C5 CX2 D1 D2 Value 103 P 630V 102 P 1KV 102 P 50V 222 P 50V 470µ 25V 220µ 25V 220µ 50V 150µ 400V 4.7µ 50V 10µ 50V X1 0.47µ 275V Y2 222P 250V 100µ 50V X2 0.1µF 275V 1N4148 BYV95C Part No. D3 BD1 D4 D5 F1 L1,L2 L4 U3 U1 U2 Q1 TX1 RT1 VZ1 Value FR103 1.0A 200V DBL406G BYT28-300 BYV32-150 250V4A QUICK 1.8µH 10µH TL431 +/-1% SG 6846 PC817 7NB60 EI-33 SCK053 14ψ 470V © 2008 Fairchild Semiconductor Corporation SG6846A • Rev. 1.1.4 www.fairchildsemi.com 13 SG6846A — Highly Integrated Green-Mode PWM Controller Physical Dimensions 5.00 4.80 3.81 8 5 A 0.65 B 6.20 5.80 4.00 3.80 1 4 1.75 5.60 PIN ONE INDICATOR (0.33) 1.27 0.25 M CBA 1.27 LAND PATTERN RECOMMENDATION 0.25 0.10 1.75 MAX C 0.10 0.51 0.33 0.50 x 45° 0.25 C SEE DETAIL A 0.25 0.19 OPTION A - BEVEL EDGE R0.10 R0.10 GAGE PLANE 0.36 OPTION B - NO BEVEL EDGE NOTES: UNLESS OTHERWISE SPECIFIED A) THIS PACKAGE CONFORMS TO JEDEC MS-012, VARIATION AA, ISSUE C, B) ALL DIMENSIONS ARE IN MILLIMETERS. C) DIMENSIONS DO NOT INCLUDE MOLD FLASH OR BURRS. D) LANDPATTERN STANDARD: SOIC127P600X175-8M. E) DRAWING FILENAME: M08AREV13 8° 0° 0.90 0.406 SEATING PLANE (1.04) DETAIL A SCALE: 2:1 Figure 22. 8-Pin Small Outline Package (SOP) Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. © 2008 Fairchild Semiconductor Corporation SG6846A • Rev. 1.1.4 www.fairchildsemi.com 14 SG6846A — Highly Integrated Green-Mode PWM Controller © 2008 Fairchild Semiconductor Corporation SG6846A • Rev. 1.1.4 www.fairchildsemi.com 15