CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
C learance N o.: FT DI# 4 9 3
Future Technology
Devices International
Limited
Datasheet
CleO35 Module
1 Introduction
1.1
The CleO35 is a smart TFT display shield for
Arduino. It includes a 3.5 inch 320x480 pixel TFT
LCD panel with resistive touch, PWM audio output
with in-built speaker amplifier for better audio
quality
The CleO35 utilises the FTDI FT903 low power MCU to
bridge between the Arduino and fast interface
accessories such as camera and SD Card input. For a
full list of the FT903’s features please see the FT90X
datasheet .In addition, the CleO35 has the following
features:
These smart TFT display shields can be easily
programmed
by
almost
anyone
to
give
professional looking HMI / GUI's with no prior
knowledge of complex graphics programming or
mathematics.
Features
Landscape and portrait modes supported
In built FTDI FT810 embedded video engine
(EVE) graphic controller
Anti-Aliased graphics throughout for much finer
image quality with no "jaggies".
Ready to use LCD module with resistive touch
in panel mountable bezel.
Micro SD card socket support.
In built 8M Byte Eflash memory
USB DFU port for firmware updates
Support camera interface
PWM audio supported and in built speaker
amplifier
Designed as Arduino and NerO shield
Compatible with FTDI CleO-RIO, CleO-Camera
and CleO-Speaker.
CE and FCC certified
N either the whole nor any part of the information contained in, or the product described in this manual, may be adapted or
reproduced in any material or elec tronic form without the prior written c onsent of the c opyright holder. T his product and its
doc umentation are s upplied on an as- is basis and no warranty as to their s uitability for any partic ular purpos e is either made or
implied. Future T ec hnology Devic es I nternational L td will not accept any claim for dama ges hows oever arising as a res ult of use or
failure of this produc t. Y our statutory rights are not affected. T his produc t or any variant of it is not intended for us e in any
medical appliance, device or s ystem in whic h the failure of the produc t might reas onably be expected to res ult in pers onal injury.
T his doc ument provides preliminary information that may be s ubject to c hange without notice. N o freedom to use patents or other
intellec tual property rights is implied by the publication of this doc ument. Fu ture Tec hnology D evices I nternational L td, U nit 1 , 2
Seaward P lac e, C enturion Business P ark, G lasgow G 4 1 1HH U nited Kingdom. Sc otland Registered C ompany N umber: SC 136640
Copyright © Future Technology Devices International Limited
1
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
C learance N o.: FT DI# 4 9 3
2 Ordering Information
Part No.
Description
CleO35A
CleO35 module, with FPC/FFC 50 LCD connector, 3.5 inch TFT LCD display
panel preinstalled, with resistive touch. Black bezel.
CleO-RIO1
Arduino Shield for users to stack Arduino board on bottom of CleO35.
CleO-CAM1
A camera plug-in module for CleO35.
CleO-SPK1
A speaker enclosure with connecting wires to CleO35.
3 Program Support
The demo applications are provided for CleO35 modules by FTDI. Visit FTDI’s website at
http://www.ftdichip.com/Products/Modules/CleO.htm for more information.
Copyright © Future Technology Devices International Limited
2
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
C learance N o.: FT DI# 4 9 3
Table of Contents
1 Introduction ................................................................. 1
1.1
Features ................................................................................ 1
2 Ordering Information .................................................... 2
3 Program Support .......................................................... 2
4 Module Hardware Feature ............................................. 5
4.1
Power Supply......................................................................... 6
4.2
Micro-controller ..................................................................... 6
4.3
Micro SD Interface ................................................................. 7
4.4
LCD Interface......................................................................... 7
4.5
Camera Interface ..................................................................10
4.6
Audio Output ........................................................................11
4.7
SPI Slave Interface ...............................................................12
4.8
External IO Pin .....................................................................13
4.9
Power and Program Interface................................................14
5 Devices Characteristics and Ratings............................. 15
5.1
Electrical Specification ..........................................................15
5.2
Display Specification .............................................................15
5.3
Optical Specification..............................................................16
6 Board Schematic ......................................................... 18
7 Block Diagram ............................................................ 21
8 Mechanical Dimensions ............................................... 22
8.1
CleO35 Module Dimensions....................................................22
8.2
Bezel Drawing.......................................................................23
9 Contact Information .................................................... 24
Appendix A – References ................................................. 25
Document References ...................................................................25
Acronyms and Abbreviations .........................................................25
Appendix B - List of Figures and Tables ............................ 26
Copyright © Future Technology Devices International Limited
3
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
C learance N o.: FT DI# 4 9 3
List of Figures ...............................................................................26
List of Tables ................................................................................26
Appendix C – Revision History.......................................... 27
Copyright © Future Technology Devices International Limited
4
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
C learance N o.: FT DI# 4 9 3
4 Module Hardware Feature
The dimensions of the CleO35 module are 101.4 mm x 73 mm X15mm. See Figure 1 for all the hardware
features.
Figure 1 – CleO35 Bottom View
Key Features:
1
3
Speaker out / Line in
3.5 in HVGA TFT I/F + Resistive Touch
5
Arduino I/F
7
8M Byte E-Flash
9
MicroSD Card Socket
11 FT903 MCU
13 FT810 GPU
2
Plastic Bezel
4
Arduino Configuration Jumpers
6
Level Shifter
8
FT903 IO Expansion
10 Camera Interface
12 USB DFU Connector
14 Audio Amplifier
Copyright © Future Technology Devices International Limited
5
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
C learance N o.: FT DI# 4 9 3
4.1 Power Supply
The CleO35 module receives power externally. Users can combine the module with the FCC/CE certified
NerO or Arduino UNO and draw power from those board supplies . For details of the NerO module, refer to
FTDI-NerO for more Information.
Alternatively, the on-board USB connector, CN4 which is primarily for debug purpose and DFU firmware
upgrade may also supply power.
Once the 5V supply is applied, a Red LED power indicator will be turned on. A step down regulator U15
will step down the 5V to 3.3V. The 3.3V supply will serve all peripherals of the FT903 microcontroller.
Figure 2 - Power Supply
4.2 Micro-controller
The FT903Q 100-pin QFN microcontroller which is provided on the board belongs to 32-bit FT90X Super
Bridging Microcontroller family from FTDI Chip. For details of the FT903Q Microcontroller, refer to the
FT90X datasheet.
Figure 3 - Micro-Controller
Copyright © Future Technology Devices International Limited
6
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
C learance N o.: FT DI# 4 9 3
4.3 Micro SD Interface
A Micro SD card slot is provided on CleO35 supporting two standards capacity card types:
Secure Digital (SD) standard – Up to 2GB SD memory card
Secure Digital High Capacity (SDHC) standard – Over 2GB-32GB SDHC memory card
The SD host controller is compatible with the standard specification V3.0. It supports up to 25MHz SD
clock speed. In the CleO35 design, the physical interface supports 4-bit SD bus mode and card detection.
Figure 4 - MicroSD Interface
4.4 LCD Interface
In the CleO35 design, a 3.5 inch TFT LCD with resistive touch is supported. The FT810Q 48pin VQFN
graphics controller IC with integrated touch and audio belongs to FTDI’s EVE series. For further details of
the FT810Q EVE graphics controller, refer to the FT81X datasheet.
The 3.5 inch LCD is connected through the 50 pin FPC/FFC connector CN1. See Table 1 for the LCD
connector pinout.
Pin No
1
2
3
Name
GND
Description
Ground
LEDA
Backlight LED Anode
LEDK
Backlight LED cathode
Copyright © Future Technology Devices International Limited
7
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
Pin No
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
C learance N o.: FT DI# 4 9 3
Name
LEDK
Description
Backlight LED cathode
LEDK
Backlight LED cathode
LEDK
Backlight LED cathode
LEDK
Backlight LED cathode
LEDK
Backlight LED cathode
GND
Ground
GND
Ground
VDD3V3
LCD VCC supply
VDD3V3
LCD VCC supply
LCD_RST
Reset
SPIM_SSn1
SPI chip select
LCD_RS
RS
SPIM_SCK
SPI clock
GND
ground
SPIM_MOSI
Master output slave input
LCD_SDO
Master input slave output
LCD_B2
Bit2 of blue RGB signal
LCD_B3
Bit3 of blue RGB signal
LCD_B4
Bit4 of blue RGB signal
LCD_B5
Bit5 of blue RGB signal
LCD_B6
Bit6 of blue RGB signal
LCD_B7
Bit7 of blue RGB signal
LCD_G2
Bit2 of green RGB signal
LCD_G3
Bit3 of green RGB signal
LCD_G4
Bit4 of green RGB signal
LCD_G5
Bit5 of green RGB signal
LCD_G6
Bit6 of green RGB signal
LCD_G7
Bit7 of green RGB signal
LCD_R2
Bit2 of red RGB signal
LCD_R3
Bit3 of red RGB signal
LCD_R4
Bit4 of red RGB signal
LCD_R5
Bit5 of red RGB signal
LCD_R6
Bit6 of red RGB signal
LCD_R7
Bit7 of red RGB signal
DE
Data enable
Copyright © Future Technology Devices International Limited
8
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
Pin No
39
40
41
42
43
44
45
46
47
48
49
50
C learance N o.: FT DI# 4 9 3
Name
DCLK
Description
Pixel clock
HSYNC
LCD horizontal sync
VSYNC
LCD vertical sync
-
IM2
-
IM1
-
IM0
GND
ground
YP
Y Top electrode of resistive
touch
X left electrode of resistive
touch
Y bottom electrode of resistive
touch
X right electrode of resistive
touch
ground
XM
YM
XP
GND
Table 1 - LCD Connector Pin Out
Figure 5 - LCD Interface
Copyright © Future Technology Devices International Limited
9
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
C learance N o.: FT DI# 4 9 3
4.5 Camera Interface
The CleO35 has a camera module interface, via a 24-pin 0.5mm pitch FFC/FPC, bottom contact
connector, CN3.In this design, support is provided for an OmniVision OV2640 camera module. A
readymade camera module (CleO-CAM1A) can be purchase from FTDI. Support for further camera
modules may be added in the future . Please visit the FTDI website for more information.
See table 2 for the Camera interface pinout
Pin No
Name
Description
1
GND
Ground
2
GND
Ground
3
I2C0_SDA
I2C serial bus, data line
4
CAM_5V
5V power supply
5
I2C0_SCL
I2C serial bus, clock line
6
RESET#
Hardware reset, active low
7
CAM_VD
Camera vertical sync input
8
CAM_PWDN
Camera module power down
signal, active high
9
CAM_HD
Camera horizontal reference
input
10
CAM_3V3
3.3V power supply
11
CAM_3V3
3.3V power supply
12
CAM_D7
Camera data line, Bit 7
13
CAM_XCLK
Camera external clock output
14
CAM_D6
Camera data line, Bit 6
15
GND
Ground
16
CAM_D5
Camera data line, Bit 5
17
CAM_PCLK
Camera pixel clock input
18
CAM_D4
Camera data line, Bit 4
19
CAM_D0
Camera data line, Bit 0
20
CAM_D3
Camera data line, Bit 3
21
CAM_D1
Camera data line, Bit 1
22
CAM_D2
Camera data line, Bit 2
23
CAM_5V
5V power supply
24
PWM0
Pulse width modulation
Table 2 - Camera Connector Pin Out
Copyright © Future Technology Devices International Limited
10
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
C learance N o.: FT DI# 4 9 3
Figure 6 - Camera Interface
4.6 Audio Output
CleO35 supports a mono speaker output through CN13. Maximum output power, can drive up to 8 OHM,
1 Watt speaker driver. A readymade speaker module (CleO-SPK1) is also available from FTDI; visit the
FTDI Chip website for more information.
An alternative, mono line-in audio input is also provided on CN13. Users can drive in their own audio
source to the on board power amplifier. See the Table 3 for the pin list for CN13.
Pin No
Pin Name
Description
1
SP-
Speaker out negative
2
SP+
Speaker out positive
3
GND
Ground
4
EXT_AUD
Ext audio line in
Table 3 - Pin List of CN3
Copyright © Future Technology Devices International Limited
11
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
C learance N o.: FT DI# 4 9 3
Figure 7 - Speaker Amplifier Circuitry
4.7 SPI Slave Interface
The CleO35 has a SPI slave interface that supports single and dual (2 data lines) SPI data transfer
modes. This interface supports both 5V, 3.3V and user defined output levels. The user defined interface
levels must be between 3V (min) to 5.5V (max). The power selection jumper is through CN10.
Pin Number
Description
5V SPI interface
1-2
3.3V SPI interface
3-4
SPI interface voltage level follow s user
setting(IOREF)
Table 4 - CN10 Jumper Selection
5-6
There are chip select (CS) jumper selections on CN11. The user has 3 options to choose for their
connection.
Description
Pin Number
SPI chip select from D5(option 1)
1-2
SPI chip select from D7(option 2)
3-4
SPI chip select from D10(option 3)
5-6
Table 5 - CN11 Jumper Selection
For the SPI Slave interface, there are two connectors for the user to interface with the master side.
The CN9 – 1X10 position 2.54mm pitch female header
The CN8 – 1X8 position 2.54mm pitch female header
Pin Number
Name
Description
1
-
No connection
2
-
No connection
3
D10
SPI Chip select option3
4
MOSI
SPI data from master side
Copyright © Future Technology Devices International Limited
12
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
C learance N o.: FT DI# 4 9 3
Pin Number
Name
Description
5
MISO
SPI data to master side
6
SCK
SPI clock
7
GND
Ground
8
-
No connection
9
-
No connection
10
-
No connection
Table 6 - CN9 Pin List
Pin Number
Name
Description
1
-
No connection
2
-
No connection
3
D2
FT903 Interrupt request out
option 1
4
D3
FT903 Interrupt request out
option 2
5
-
No connection
6
D5
SPI Chip select option1
7
-
No connection
8
D7
SPI Chip select option2
Table 7 - CN8 Pin List
4.8 External IO Pin
There are extra features provided on CN5, 16 position 0.5mm pitch FFC/FPC connector. Users can
connect to external feature boards through this connector.
See Table 8 for all the extra feature s assigned to each pin.
Pin Number
1
2
3
4
5
6
7
8
9
Name
Description
GPIO61
General purpose IO 61
GPIO60
General purpose IO 60
PWM2
Pulse Width Modulation 2
PWM1
Pulse Width Modulation 1
VDD3V3
3.3V supply
GND
Ground
I2C1_SCL
I2C1 Serial Clock
I2C1_SDA
I2C1 Serial Data
UART0_RXD
UART0 receive
Copyright © Future Technology Devices International Limited
13
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
10
11
12
13
14
15
16
UART0_TXD
UART0 transmit
VDD3V3
3.3V supply
GND
Ground
SPIM_MISO
SPI3 Master Input
SPIM_MOSI
SPI3 Master Output
SPIM_SSn3
SPI3 Chip Select
SPIM_SCK
SPI3 Clock Line
C learance N o.: FT DI# 4 9 3
Table 8 - CN5 Pin List
There is a jumper selection for the FT903 interrupt request through CN12. Users have 2 option to choose
from.
Pin Number
Description
Connect to Arduino/NerO MCU int0(D2)
1-2
Connect to Arduino/NerO MCU int1(D3)
3-4
Table 9 - CN12 Jumper Selection
4.9 Power and Program Interface
The power interface CN6, 1X8 position 2.54mm pitch female heade r, may be driven by NerO or an
Arduino UNO.
Users can use the USB connector CN4 for FT903 firmware upgrades. For the details of the tool operation,
refer to AN_325 FT900 Tool Chain Installation Guide .
Pin Number
Name
Description
1
NC
NC
2
IOREF
IO reference voltage
3
RESET
FT903 reset pin
4
-
No connection
5
VDD5V
5V supply
6
GND
ground
7
GND
ground
8
-
No connection
Table 10 - CN6 Pin List
Copyright © Future Technology Devices International Limited
14
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
C learance N o.: FT DI# 4 9 3
5 Devices Characteristics and Ratings
5.1 Electrical Specification
Conditions
Parameter
Value
Unit
Storage Temperature
-30°C to 80°C
Degrees C
Ambient Operating Temperature (Power
-20°C to 70°C
Degrees C
Applied)
Table 11 - Temperature Parameter
DC Characteristics (Ambient Temperature = -20°C to +70°C)
Parameter
Description
Minimum
Typical
Maximum
Units
V
bus
USB power supply
4.75
5.25
V
V
DC
DC power supply
4.75
5.25
V
Iusb
USB power supply
current
500
mA
IDC
DC Supply Current
500
mA
I
USB current in idle
mode
idle
140
mA
Vio
3.3 Vio voltage
reference
3.0
Vih
Input high voltage
2
Vil
Input low voltage
Voh
output high voltage
Vol
output low voltage
0.4
Table 12 - Operating Voltage and Current
3.3
3.6
Conditions
External source
With LCD and
backlight on
V
0.8
2.4
5.2 Display Specification
Item
Spec
Units
Display area(AA)
49.0(H) * 73.4(V)
mm
Driver Element
TFT active matrix
mA
Display Colours
262K
-
Number of Pixels
320(RGB)*480
dots
Pixel pitch
0.051(H) * 0.051(V)
mm
Copyright © Future Technology Devices International Limited
Notes
3.5 inch diagonal
15
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
Item
Spec
Units
Viewing Angle
6:00
o’clock
Display mode
Transmissive/ Normally White
-
LCD Luminance
100
cd/m2
Touch screen
resistive
Table 13 - Display Specifications
C learance N o.: FT DI# 4 9 3
Notes
Portrait view
-
5.3 Optical Specification
Copyright © Future Technology Devices International Limited
16
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
C learance N o.: FT DI# 4 9 3
Figure 8 - 3.5 inch TFT Optical Specifications
Copyright © Future Technology Devices International Limited
17
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
C learance N o.: FT DI# 4 9 3
6 Board Schematic
Figure 9 - Sheet1 - FT810Q Connection
Copyright © Future Technology Devices International Limited
18
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
C learance N o.: FT DI# 4 9 3
Figure 10 - Sheet2 - FT903Q Connection
Copyright © Future Technology Devices International Limited
19
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
C learance N o.: FT DI# 4 9 3
Figure 11 - Sheet3 - Power and Connectors
Copyright © Future Technology Devices International Limited
20
Speaker
Connector
3.5 inch TFT
LCD with
resistive
Touch
Speaker
Amplifier
RGB
PWM
Copyright © Future Technology Devices International Limited
External
connector
External
connector
CN5
Serial Flash
W25Q64F
V
SPIM 1
FT810
MicroSD
card Slot
SPIS 1
SPIM 3
SPIM 2
SPIM 0
SDIO
FT903
Q
GPIO
I2C1
PWM1 &
PWM2
UART0
DP & DM
PWM0
I2C0
CAM_D
Interface
External
connector
CN5
Debug port
Micro USB
Slot
Camera
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
C learance N o.: FT DI# 4 9 3
7 Block Diagram
Figure 12 - CleO35 Block Diagram
21
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
C learance N o.: FT DI# 4 9 3
8 Mechanical Dimensions
8.1 CleO35 Module Dimensions
101.4mm
73mm
15mm
Figure 13 - Cleo35 Module Dimensions
Copyright © Future Technology Devices International Limited
22
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
C learance N o.: FT DI# 4 9 3
8.2 Bezel Drawing
Figure 14 - CleO35 Bezel Drawing
Copyright © Future Technology Devices International Limited
23
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
C learance N o.: FT DI# 4 9 3
9 Contact Information
Head Office – Glasgow, UK
Branch Office – Tigard, Oregon, USA
Future Technology Devices International Limited
Unit 1, 2 Seaward Place, Centurion Business Park
Glasgow G41 1HH
United Kingdom
Tel: +44 (0) 141 429 2777
Fax: +44 (0) 141 429 2758
Future Technology Devices International Limited (USA)
7130 SW Fir Loop
Tigard, OR 97223-8160
USA
Tel: +1 (503) 547 0988
Fax: +1 (503) 547 0987
E-mail (Sales)
E-mail (Support)
E-mail (General Enquiries)
E-mail (Sales)
E-mail (Support)
E-mail (General Enquiries)
sales1@ftdichip.com
support1@ftdichip.com
admin1@ftdichip.com
us.sales@ftdichip.com
us.support@ftdichip.com
us.admin@ftdichip.com
Branch Office – Taipei, Taiwan
Branch Office – Shanghai, China
Future Technology Devices International Limited (Taiwan)
2F, No. 516, Sec. 1, NeiHu Road
Taipei 114
Taiwan , R.O.C.
Tel: +886 (0) 2 8797 1330
Fax: +886 (0) 2 8751 9737
Future Technology Devices International Limited (China)
Room 1103, No. 666 West Huaihai Road,
Shanghai, 200052
C hina
Tel: +86 21 62351596
Fax: +86 21 62351595
E-mail (Sales)
E-mail (Support)
E-mail (General Enquiries)
E-mail (Sales)
E-mail (Support)
E-mail (General Enquiries)
tw .sales1@ftdichip.com
tw .support1@ftdichip.com
tw .admin1@ftdichip.com
cn.sales@ftdichip.com
cn.support@ftdichip.com
cn.admin@ftdichip.com
Web Site
http://ftdichip.com
Distributor and Sales Representatives
Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s)
in your country.
System and equipment manufac turers and des igners are res ponsible to ens ure that their s ys tems , and any Future T ec hnolog y D evices
I nternational L td (FTDI ) devices incorporated in their sys tems , meet all applic able safety, regulatory and sys tem -level performance requirements .
All application- related information in this document (including applic ation desc riptions , s uggested FTDI devic es and other materials ) is provided
for referenc e only. While FTDI has taken care to ass ure it is acc urate, this information is s ubject to c ustomer confirmation, and FTDI disclaims all
liability for s ys tem des igns and for any applic ations ass ista nce provided by FTDI . Use of FTDI devic es in life s upport and/or s afety applic ations is
entirely at the user’s risk, and the us er agrees to defend, indemnify and hold harmless FTDI from any and all damages , claims , s uits or expense
res ulting from s uch us e. T his doc ument is s ubject to c hange without notice. N o freedom to us e patents or other intellec tual property rights is
implied by the public ation of this doc ument. N either the whole nor any part of the information c ontained in, or the produc t d esc ribed in this
doc ument, may be adapted or reproduc ed in any material or elec tronic form without the prior written c onsent of the c opyright holder. Future
Tec hnology Devices I nternational L td, U nit 1 , 2 Seaward P lac e, Centurion Business Park, Glas gow G41 1HH , U nited Kingdom. Scotland Registered
C ompany N umber: SC136640
Copyright © Future Technology Devices International Limited
24
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
C learance N o.: FT DI# 4 9 3
Appendix A – References
Document References
For module documentations, please refer to URL below:
FT90X series datasheet: FT90X Series Datasheet
FT900 tool chain installation guide : FT900 Tool Chain Installation Guide
FT900 Bootloader DFU usage guide: FT900 Bootloader DFU Usage Application Note
Acronyms and Abbreviations
Terms
Description
DC
Direct Current
DFU
Device Firmware Update
EVE
Embedded Video Engine
FCC/CE
North American EMI Verification/European Union EMC & Safety
Compliance Declaration
FFC/FPC
Flexible Flat Cable/Flexible Printed Circuit
GPU
HVGA
IO
Graphics Processing Unit
Half Size Video Graphics Array
Input/output
LCD
Liquid Crystal Display
LED
Light-emitting diode
MCU
Microcontroller Unit
QFN
Quad-flat no-leads
SD
Secure Digital
SPI
Serial Peripheral Interface
SDHC
USB
VQFN
Secure Digital High Capacity
Universal Serial Bus
Very Thin Quad Flat Non-Leaded Package
Copyright © Future Technology Devices International Limited
25
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
C learance N o.: FT DI# 4 9 3
Appendix B - List of Figures and Tables
List of Figures
Figure 1 – CleO35 Bottom View .............................................................................................................. 5
Figure 2 - Power Supply ......................................................................................................................... 6
Figure 3 - Micro-Controller...................................................................................................................... 6
Figure 4 - MicroSD Interface................................................................................................................... 7
Figure 5 - LCD Interface ......................................................................................................................... 9
Figure 6 - Camera Interface ................................................................................................................. 11
Figure 7 - Speaker Amplifier Circuitry ................................................................................................... 12
Figure 8 - 3.5 inch TFT Optical Specifications ........................................................................................ 17
Figure 9 - Sheet1 - FT810Q Connection ................................................................................................ 18
Figure 10 - Sheet2 - FT903Q Connection .............................................................................................. 19
Figure 11 - Sheet3 - Power and Connectors .......................................................................................... 20
Figure 12 - CleO35 Block Diagram ........................................................................................................ 21
Figure 13 - Cleo35 Module Dimensions ................................................................................................. 22
Figure 14 - CleO35 Bezel Drawing ........................................................................................................ 23
List of Tables
Table 1 - LCD Connector Pin Out ............................................................................................................ 9
Table 2 - Camera Connector Pin Out ..................................................................................................... 10
Table 3 - Pin List of CN3 ....................................................................................................................... 11
Table 4 - CN10 Jumper Selection .......................................................................................................... 12
Table 5 - CN11 Jumper Selection .......................................................................................................... 12
Table 6 - CN9 Pin List ........................................................................................................................... 13
Table 7 - CN8 Pin List........................................................................................................................... 13
Table 8 - CN5 Pin List ........................................................................................................................... 14
Table 9 - CN12 Jumper Selection .......................................................................................................... 14
Table 10 - CN6 Pin List ......................................................................................................................... 14
Table 11 - Temperature Parameter ....................................................................................................... 15
Table 12 - Operating Voltage and Current ............................................................................................. 15
Table 13 - Display Specifications .......................................................................................................... 16
Copyright © Future Technology Devices International Limited
26
CleO35 Module Datasheet
Version 1.0
D oc ument Reference N o.: FT _001299
C learance N o.: FT DI# 4 9 3
Appendix C – Revision History
Document Title:
CleO35 Module Datasheet
Document Reference No.:
FT_001299
Clearance No.:
FTDI# 493
Product Page:
http://www.ftdichip.com/Products/Modules/CleO.htm
Document Feedback:
Send Feedback
Revision
Changes
Date
Version 1.0
Initial Release
2016-04-20
Copyright © Future Technology Devices International Limited
27
工商网监
湘ICP备2023018690号
