UMFTPD3A

UMFTPD3A Datasheet Version 1.0 Document Reference No.: FT_001318 Clearance No.: FTDI# 502 Future Technology Devices International UMFTPD3A Datasheet Universal programming Module UMFTPD3A is a universal programming module for OTP memory and eFUSE programming. 1 Introduction The UMFTPD3A Universal Programmer Module is used to provide an external programming voltage (Vpp) that covers 1.5 to 6.5V to program FTDI development modules and ICs with internal OTP memory or eFUSE (electrical poly-fuse). The embedded OTP memory or eFUSE in the FTDI chips is used to store USB Vendor ID (VID), Product ID (PID), device serial number, product description string and chip configuration information. Users can store this vendor specific information in the OTP or eFUSE and save the cost of an external EEPROM from the BOM. The UMFTPD3A assists the user in programming the OTP memory or eFUSE directly through a USB host controller with FTDI’s programming software tool, FT_Prog. 1.1 Features The UMFTPD3A has the following features:  Micro USB-B connector allows the UMFTPD3A to be connected to a host system via a standard USB A to Micro B cable.  Downstream port using USB-A type connector allows target devices to be connected to the UMFTPD3A.  On board FTDI chip provides USB hub function  Supports wide programming voltages from 1.5V to 6.5V for FT260 and FT4222H series.  3 pin connector to deliver VPP programming power  Visual indicator for VPP programming voltage and USB bus power by using LEDs.  USB2.0 Full Speed compatible. Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology Devices International Ltd will not accept any claim for damages howsoever arising as a result of u se or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH United Kingdom. Scotland Registered Company Number: SC136640 Copyright © Future Technology Devices International Limited 1 UMFTPD3A Datasheet Version 1.0 Document Reference No.: FT_001318 Clearance No.: FTDI# 502 Table of Contents 1 Introduction .................................................................... 1 1.1 Features .................................................................................... 1 2 Driver Support ................................................................ 3 3 Ordering Information ...................................................... 4 4 UMFTPD3A Signals .......................................................... 5 5 4.1 UMFTPD3A Pin Out and connectors ........................................... 5 4.2 J1 Signal Descriptions ............................................................... 6 4.3 USB Connectors Descriptions .................................................... 6 4.4 LED Descriptions ....................................................................... 6 Hardware Setup Guide .................................................... 7 5.1 Module Connect to PC with USB Host ........................................ 7 5.2 Module Connect to Device under programming ......................... 7 5.3 FT_PROG Programming Utility .................................................. 8 6 Support Chips List ........................................................... 9 7 Module Dimensions ....................................................... 10 8 UMFTPD3A Module Circuit Schematic ............................ 11 9 Contact Information ...................................................... 13 Appendix A – References ................................................... 14 Document References ..................................................................... 14 Acronyms and Abbreviations ........................................................... 14 Appendix B – List of Figures and Tables ............................. 15 List of Figures ................................................................................. 15 List of Tables ................................................................................... 15 Appendix C – Revision History ........................................... 16 Copyright © Future Technology Devices International Limited 2 UMFTPD3A Datasheet Version 1.0 Document Reference No.: FT_001318 Clearance No.: FTDI# 502 2 Driver Support Royalty free D2XX Direct Drivers (USB Drivers + DLL S/W Interface):  Windows 10 32,64-bit  Windows 8.1 32,64-bit  Windows 8 32,64-bit  Windows 7 32,64-bit The above listed drivers are all available for download from http://www.ftdichip.com/FTDrivers.htm. For driver installation instructions, refer to http://www.ftdichip.com/Support/Documents/InstallGuides.htm Copyright © Future Technology Devices International Limited 3 UMFTPD3A Datasheet Version 1.0 Document Reference No.: FT_001318 Clearance No.: FTDI# 502 3 Ordering Information Module Code Description UMFTPD3A Universal FTDI programmer module Copyright © Future Technology Devices International Limited 4 UMFTPD3A Datasheet Version 1.0 Document Reference No.: FT_001318 Clearance No.: FTDI# 502 4 UMFTPD3A Signals 4.1 UMFTPD3A Pin Out and connectors Figure 4.1 Module Pin Out and connectors Copyright © Future Technology Devices International Limited 5 UMFTPD3A Datasheet Version 1.0 Document Reference No.: FT_001318 4.2 Clearance No.: FTDI# 502 J1 Signal Descriptions Connector Pin Name Type J1-1 GND Ground J1-2 VPP Power J1-3 GND Ground Description Ground 0 volts. Programming voltage output Ground 0 volts. Table 4.1 J1 Pin Out Description 4.3 USB Connectors Descriptions UMFTPD3A provides two USB connectors: Connector No. Description CN1 Upstream USB port connect to the USB Host CN2 Downstream USB port connect to the device under programming Table 4.2 USB connectors Description 4.4 LED Descriptions There are two LED indicators on the UMFTPD3A: LED No. Description D2 USB VBUS Supply from Upstream Port D4 VPP Power Supply Table 4.3 LED Description Copyright © Future Technology Devices International Limited 6 UMFTPD3A Datasheet Version 1.0 Document Reference No.: FT_001318 Clearance No.: FTDI# 502 5 Hardware Setup Guide 5.1 Module Connect to PC with USB Host The first time the UMFTPD3A module is connected to a Windows PC, the USB device drivers need to be installed. Windows will install the driver automatically via Windows Update if a network is connected or the driver installation package may be downloaded from the FTDI Website for manual installation. Figure 5.1 Module connected to PC with USB host 5.2 Module Connect to Device under programming Figure 5.2 shows the connection between a UMFTPD3A and a target device with an FTDI chip. The UMFTPD3A is designed to control VPP power output for programming the OTP memory or eFUSE on the target board with an FTDI chip. VPP power is supplied through the 3 pin header with 2.54mm pitch, J1. Figure 5.2 Module connected to device under programming Warning: The programming connector definition may differ between FTDI development modules and 3rd party design. Please check FTDI development module datasheet or documentation for 3rd party designs before wiring the VPP connection. Warning: The UMFTPD3A is only allowed to connect and program one FTDI chip at a time. Copyright © Future Technology Devices International Limited 7 UMFTPD3A Datasheet Version 1.0 Document Reference No.: FT_001318 5.3 Clearance No.: FTDI# 502 FT_PROG Programming Utility Having connected the UMFTPD3A module, the user can perform the OTP memory or eFUSE programming with the FT_PROG utility. The FT_PROG will detect the ICs via USB and configure the UMFTPD3A programing voltage by itself. FT_PROG is a free programming utility for use with FTDI devices. For more details, refer to the FTDI website. Figure 5.3 FT_PROG example for FT4222H programming Copyright © Future Technology Devices International Limited 8 UMFTPD3A Datasheet Version 1.0 Document Reference No.: FT_001318 Clearance No.: FTDI# 502 6 Support Chips List The FTDI Chips compatible with UMFTPD3A are listed below. FTDI Chip Memory Type Programming voltage Development Module FT4222H OTP 6.5V UMFT4222EV FT260 eFUSE 3.8V UMFT260EV1A Table 6.1 Compatible Devices list Copyright © Future Technology Devices International Limited 9 UMFTPD3A Datasheet Version 1.0 Document Reference No.: FT_001318 Clearance No.: FTDI# 502 7 Module Dimensions Figure 7.1 UMFTPD3A Module Dimensions All dimensions are given in millimetres. The UMFTPD3A module exclusively uses lead free components, and is fully compliant with European Union directive 2002/95/EC. Copyright © Future Technology Devices International Limited 10 UMFTPD3A Datasheet Version 1.0 Document Reference No.: FT_001318 Clearance No.: FTDI# 502 8 UMFTPD3A Module Circuit Schematic Figure 8.1 Module Circuit Schematic Copyright © Future Technology Devices International Limited 11 UMFTPD3A Datasheet Version 1.0 Document Reference No.: FT_001318 Clearance No.: FTDI# 502 Figure 8.2 Module Circuit Schematic (Cont’d) Copyright © Future Technology Devices International Limited 12 UMFTPD3A Datasheet Version 1.0 Document Reference No.: FT_001318 Clearance No.: FTDI# 502 9 Contact Information Head Office – Glasgow, UK Branch Office – Tigard, Oregon, USA Unit 1, 2 Seaward Place, Centurion Business Park Glasgow G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 7130 SW Fir Loop Tigard, OR 97223 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) E-Mail (Sales) E-Mail (Support) E-Mail (General Enquiries) sales1@ftdichip.com support1@ftdichip.com admin1@ftdichip.com Branch Office – Taipei, Taiwan 2F, No. 516, Sec. 1, NeiHu Road Taipei 114 Taiwan , R.O.C. Tel: +886 (0) 2 8797 1330 Fax: +886 (0) 2 8751 9737 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) tw.sales1@ftdichip.com tw.support1@ftdichip.com tw.admin1@ftdichip.com us.sales@ftdichip.com us.support@ftdichip.com us.admin@ftdichip.com Branch Office – Shanghai, China Room 1103, No. 666 West Huaihai Road, Shanghai, 200052 China Tel: +86 (0)21 6235 1596 Fax: +86 (0)21 6235 1595 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) cn.sales@ftdichip.com cn.support@ftdichip.com cn.admin@ftdichip.com Web Site http://ftdichip.com Distributor and Sales Representatives Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. System and equipment manufacturers and designers are responsible to ensure that their systems, and any Future Technology Devices International Ltd (FTDI) devices incorporated in their systems, meet all applicable safety, regulatory and system-level performance requirements. All application-related information in this document (including application descriptions, suggested FTDI devices and other materials) is provided for reference only. While FTDI has taken care to assure it is accurate, this information is subject to customer confirmation, and FTDI disclaims all liability for system designs and for any applications assistance provided by FTDI. Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, ind emnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. This document is subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Neither the whole nor any part of the information contained in, or the product described in this document, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH, United Kingdom. Scotland Registered Company Number: SC136640 Copyright © Future Technology Devices International Limited 13 UMFTPD3A Datasheet Version 1.0 Document Reference No.: FT_001318 Clearance No.: FTDI# 502 Appendix A – References Document References Application Notes AN_124 User Guide for FTDI FT_Prog Utility Datasheets DS_FT4222H DS_UMFT4222EV DS_FT260 DS_UMFT260EV FT_PROG Utility http://www.ftdichip.com/Support/Utilities.htm#FT_Prog Acronyms and Abbreviations Terms Description eFUSE Electrical poly fuse OTP One Time Programming USB Universal Serial Bus Copyright © Future Technology Devices International Limited 14 UMFTPD3A Datasheet Version 1.0 Document Reference No.: FT_001318 Clearance No.: FTDI# 502 Appendix B – List of Figures and Tables List of Figures Figure 4.1 Module Pin Out and connectors ....................................................................................... 5 Figure 5.1 Module connect to PC with USB host ................................................................................ 7 Figure 5.2 Module connect to device under programming ................................................................... 7 Figure 5.3 I/O voltage level with internal regulator: JP1 shorted ......................................................... 8 Figure 6.1 UMFTPD3A Module Dimensions ...................................................................................... 10 Figure 7.1 Module Circuit Schematic.............................................................................................. 11 List of Tables Table 4.1 J1 Pin Out Description ..................................................................................................... 6 Table 4.2 USB connectors Description ............................................................................................. 6 Table 4.3 LED Description .............................................................................................................. 6 Table 6.1 Compatible Devices list.................................................................................................... 9 Copyright © Future Technology Devices International Limited 15 UMFTPD3A Datasheet Version 1.0 Document Reference No.: FT_001318 Clearance No.: FTDI# 502 Appendix C – Revision History Document Title: UMFTPD3A Datasheet Document Reference No.: FT_001318 Clearance No.: FTDI# 502 Product Page: http://www.ftdichip.com Document Feedback: Send Feedback Revision Version 1.0 Changes Initial Release Date 2016-05-23 Copyright © Future Technology Devices International Limited 16