FTR-K1AR005E-MB-RG

FTR-K1 SERIES POWER RELAY 1 POLE - 16A/12A/10A Transparent cover FTR-K1 Series n FEATURES l l 16A, 12A, 10A versions Transparent cover l Low profile (height: 15.7mm) l High insulation Insulation distance (between coil and contacts): 10mm min. Dielectric strength: 5KV Surge strength: 10KV l UL F class isolation wire l Low coil power (400mW) l Cadmium free contacts l Safety standards UL, CSA, VDE, SEMKO approved UL, CSA TV-5 rating approved (1 form A type) l RoHS compliant Please see page 13 for more information n PARTNUMBER INFORMATION FTR-K1 C K 05 W - MA - RG 0 [Example] (a) (b) (c) (d) (e) (f) (g) (a) (b) (c) (d) (e) Relay type Contact configuration Coil type Coil rated voltage Contact material Contact rating/Terminal pitch Special type FTR-K: FTR-K Series A C K L 005 W T E : 1 form A (SPST-NO) : 1 form C (SPDT) (standard type "K" only) : Standard type (400mW) / flux free : High sensitive (250mW) / flux free : 5.....48 VDC Coil rating table at page 7 : AgSnO2 (applicable for 16A, 1 form A) (TV-5) : AgNi (90/10) : AgSnO2 (applicable for 1 form C) (f) (g) Nil : 16A, 5mm pitch MA : 12A and 3.5mm ptich MB : 12A and 5.0mm pitch LA : 10A and 3.5mm pitch LB : 10A and 5.0mm pitch RG : Transparent cover Actual marking does not carry the type name : "FTR" E.g.: Ordering code: FTR-K1CK005W Actual marking: K1CK005W ("RG" is marked on the relay)  FTR-K1 SERIES FTR-K1 SERIES n SPECIFICATION 16A type Item Contact Data Configuration Construction Material Resistance (initial) Contact rating (resistive) Max. carrying current * Max. switching voltage Max. switching power Min. switching load *2 Life Mechanical AC contact rating Electrical DC contact rating Coil Data Rated power (20 °C) Operate power (20 °C) Operating temperature range Timing Data Insulation Operate (at nominal voltage) Release (at nominal voltage) Resistance (initial) Dielectric strength Surge strength Clearance Creepage EN61810-1, VDE0435 Voltage Pollution degree Material group Category Other Vibration resistance Shock Weight Endurance Endurance Open contacts Contacts to coil Coil to contacts FTR-K1 AK ( ) (T,W)-RG FTR-K1 CK ( ) (W,E)-RG 1 form A Single T, W: AgSnO2 , E: AgNi 1 form C Maximum 100mΩ at 1A, 6VDC 16A, 250VAC / 24VDC 16A 440VAC / 300VDC 4,000VA / 384W 10mA, 5VDC 20 x 106 operations minimum 100 x 103 operations minimum 100 x 103 operations minimum 50 x 103 operations minimum 30 x 103 operations minimum 400mW (430mW at 48V coil) 200mW (210mW at 48V coil) -40 °C to +70 °C (no frost) ≤ 15ms (no bounce, no diode) ≤ 5ms (no bounce, no diode) ≥ 1,000MOhm at 500VDC 1,000VAC (50/60Hz) 1min 5,000VAC (50/60Hz) 1min 10,000V / 1.2 x 50µs standard wave 10mm 10mm 250V 3 III a C / 250V (Reference voltage) (VDE0110b) 10 to 55Hz double amplitude 1.5mm 1,000m/s² (6 ± 1ms) Approximately 13g Misoperation≥1us 10 to 55Hz double amplitude 0.7mm Misoperation≥1us 100m/s² (11 ± 1ms) * 1: Need to consider the heat from PCB when max. current is more than 10A. * 2: Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental contions 2 FTR-K1 SERIES FTR-K1 SERIES n SPECIFICATION 12A type Item Contact Data Configuration Construction Material Resistance (initial) Contact rating (resistive) Max. carrying current * Max. switching voltage Max. switching power Min. switching load *2 Life Mechanical Electrical Coil Data Rated power (20 °C) Operate power (20 °C) Operating temperature range Timing Data Insulation Operate (at nominal voltage) Release (at nominal voltage) Resistance (initial) Dielectric strength Surge strength Clearance Creepage EN61810-1, VDE0435 Voltage Pollution degree Material group Category Other Vibration resistance Shock Weight Endurance Endurance Open contacts Contacts to coil Coil to contacts AC contact rating DC contact rating FTR-K1 AK ( ) (W, E) - (MA, MB) - RG 1 form A Single W: AgSnO2 , E: AgNi FTR-K1 CK ( ) (W, E) - (MA, MB) - RG 1 form C Maximum 100mΩ at 1A, 6VDC 12A, 250VAC / 24VDC 14A 440VAC / 300VDC 3,000VA / 288W 10mA, 5VDC 20 x 106 operations minimum 100 x 103 operations minimum 100 x 103 operations minimum 400mW (430mW at 48V coil) 200mW (210mW at 48V coil) -40 °C to +70 °C (no frost) ≤ 15ms (no bounce) ≤ 5ms (no bounce, no diode) ≥ 1,000MOhm at 500VDC 1,000VAC (50/60Hz) 1min 5,000VAC (50/60Hz) 1min 10,000V / 1.2 x 50µs standard wave 10mm 10mm 250V 3 III a C / 250V (Reference voltage) (VDE0110b) 10 to 55Hz double amplitude 1.5mm 1,000m/s² (6 ± 1ms) Approximately 13g Misoperation≥1us 10 to 55Hz double amplitude 0.7mm Misoperation≥1us 100m/s² (11 ± 1ms) * 1: Need to consider the heat from PCB when max. current is more than 10A. * 2: Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental contions 3 FTR-K1 SERIES FTR-K1 SERIES n SPECIFICATION 10A type Item Contact Data Configuration Construction Material Resistance (initial) Contact rating (resistive) Max. carrying current Max. switching voltage Max. switching power Min. switching load * Life Coil Data Mechanical Electrical Rated power (20 °C) Operate power (20 °C) Operating temperature range Timing Data Insulation Operate (at nominal voltage) Release (at nominal voltage) Resistance (initial) Dielectric strength Surge strength Clearance Creepage EN61810-1, VDE0435 Voltage Pollution degree Material group Category Other Vibration resistance Shock Weight Endurance Endurance Open contacts Contacts to coil Coil to contacts AC contact rating FTR-K1 AL ( ) (W, E) - (LA, LB) - RG 1 form A Single W: AgSnO2 , E: AgNi Maximum 100mΩ at 1A, 6VDC 10A, 250VAC / 24VDC 10A 440VAC 2,500VA 10mA, 5VDC 20 x 106 operations minimum 100 x 103 operations minimum 250mW 141mW -40 °C to +70 °C (no frost) ≤ 15ms (no bounce, no diode) ≤ 5ms (no bounce, no diode) ≥ 1,000MOhm at 500VDC 1,000VAC (50/60Hz) 1min 5,000VAC (50/60Hz) 1min 10,000V / 1.2 x 50µs standard wave 10mm 10mm 250V 3 III a C / 250V (Reference voltage) (VDE0110b) 10 to 55Hz double amplitude 1.5mm 1,000m/s² (6 ± 1ms) Approximately 13g Misoperation≥1us 10 to 55Hz double amplitude 0.7mm Misoperation≥1us 100m/s² (11 ± 1ms) * Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental contions and expected reliability levels. 4 FTR-K1 SERIES FTR-K1 SERIES n PART NUMBERS 16A and AgSnO2 contacts Ordering part number FTR-K1AK(...)T-RG FTR-K1CK(...)W-RG Contact A: 1 form A C: 1 form C Coil power K: 400mW Contact material T: AgSnO2 W: AgSnO2 Current Nil: 16A Special RG: Transparent cover 16A and AgNi contacts Ordering part number FTR-K1AK(...)E-RG FTR-K1CK(...)E-RG Contact A: 1 form A C: 1 form C Coil power K: 400mW Contact material E: AgNi (90/10) Current Nil: 16A Special RG: Transparent cover 12A, 3.5mm pitch and AgSnO2 contacts Ordering part number FTR-K1AK(...)W-MA-RG FTR-K1CK(...)W-MA-RG Contact A: 1 form A C: 1 form C Coil power K: 400mW Contact material W: AgSnO2 Current MA: 12A Special RG: Transparent cover 12A, 3.5mm pitch and AgNi contacts Ordering part number FTR-K1AK(...)E-MA-RG FTR-K1CK(...)E-MA-RG Contact A: 1 form A C: 1 form C Coil power K: 400mW Contact material E: AgNi (90/10) Current MA: 12A Special RG: Transparent cover 12A, 5.0mm pitch and AgSnO2 contacts Ordering part number FTR-K1AK(...)W-MB-RG FTR-K1CK(...)W-MB-RG Contact A: 1 form A C: 1 form C Coil power K: 400mW Contact material W: AgSnO2 Current MB: 12A Special RG: Transparent cover (...) = coil voltage 5 FTR-K1 SERIES FTR-K1 SERIES n PART NUMBERS 12A, 5.0mm pitch and AgNi contacts Ordering part number FTR-K1AK(...)E-MB-RG FTR-K1CK(...)E-MB-RG Contact A: 1 form A C: 1 form C Coil power K: 400mW Contact material E: AgNi (90/10) Current MB: 12A Special RG: Transparent cover 10A, 3.5mm pitch and AgSnO2 contacts Ordering part number FTR-K1AL(...)W-LA-RG Contact A: 1 form A Coil power L: 250mW Contact material W: AgSnO2 Current LA: 10A Special RG: Transparent cover 10A, 3.5mm pitch and AgNi contacts Ordering part number FTR-K1AL(...)E-LA-RG Contact A: 1 form A Coil power L: 250mW Contact material E: AgNi (90/10) Current LA: 10A Special RG: Transparent cover 10A, 5.0mm pitch and AgSnO2 contacts Ordering part number FTR-K1AL(...)W-LB-RG Contact A: 1 form A Coil power L: 250mW Contact material W: AgSnO2 Current LB: 10A Special RG: Transparent cover 10A, 5.0mm pitch and AgNi contacts Ordering part number FTR-K1AL(...)E-LB-RG Contact A: 1 form A Coil power L: 250mW Contact material E: AgNi (90/10) Current LB: 10A Special RG: Transparent cover (...) = coil voltage 6 FTR-K1 SERIES FTR-K1 SERIES n COIL RATING 250 mW coils Coil Code 005 006 009 012 018 024 048 Rated Coil Coil Resistance Voltage +/- 10% (Ohm) (VDC) 5 6 9 12 18 24 48 100 145 325 575 1300 2310 9216 Must Operate Must ReleaseMax. Coil Voltage Voltage Voltage (VDC) (VDC) * (VDC) * 3.75 4.5 6.75 9 13.5 18 36 0.5 0.6 0.9 1.2 1.8 2.4 4.8 15 18 27 36 54 72 144 250 Rated Power (mW) Note: All values in the table are valid for 20°C and zero contact current. * Specified operate values are valid for pulse wave voltage. 400 mW coils Coil Code 005 006 009 012 018 022 024 028 048 Rated Coil Coil Resistance Voltage +/- 10% (Ohm) (VDC) 5 6 9 12 18 22 24 28 48 62 90 202 360 810 1210 1440 1960 5360 Must Operate Must ReleaseMax. Coil Voltage Voltage Voltage (VDC) (VDC) * (VDC) * 3.5 4.2 6.3 8.4 12.6 15.4 16.8 19.6 33.6 0.5 0.6 0.9 1.2 1.8 2.2 2.4 2.8 4.8 12.2 14.7 22 29.4 44.1 53.9 58.8 68.6 117.6 430 400 Rated Power (mW) Note: All values in the table are valid for 20°C and zero contact current. * Specified operate values are valid for pulse wave voltage. 7 FTR-K1 SERIES FTR-K1 SERIES n SAFETY STANDARDS 16A type Type UL Compliance UL 508 E63614 Contact rating FTR-K1AK ( ) (T,E)-RG Flammability: UL 94-VII (plastics) 16A, 24 VAC (resisitive) 16A, 277VAC (resisitive) 20A, 277VAC (resisitive) 1 HP, 277VAC 1/2 HP, 125VAC TV-5, 120VAC, 120VAC 25,000 cycles Pilot duty: A300 16A, 277 VAC/24VDC (resisitive) 20A, 277VAC (resistive) 1 HP, 277VAC 1/2 HP, 125VAC 1/8 HP, 125VAC TV-5, 250VAC 25,000 cycles Pilot duty: B300 16A, 277 VAC/24VDC (resisitive) 20A, 277VAC (resistive) 1 HP, 277VAC 1/2 HP, 125VAC 1/8 HP, 125VAC TV-5, 120VAC 25,000 cycles Pilot duty: B300 16A, 250 VAC (cosØ=1) 3.5A, 250 VAC (cosØ=0.4) 16 A 24VDC (0ms) 5A/80A, 250 VAC (only T-type) 16A, 250 VAC (cosØ=1) 3.5A, 250 VAC (cosØ=0.4) 16A 24VDC (0ms) 250VAC, 16(3)A40T70 FTR-K1CK ( ) W CSA C22.2 No. 14 LR 40304 VDE 0435, 0631, 0700, 0860 40013848 SEMKO EN 61058-1:1992 and A1 250VAC, 16 (3)A 40T70 EN 61095:1993 and A1+A11 5A/80A 250VAC (only T-type) Complies with NEMKO, DEMKO, FIMKO 8 FTR-K1 SERIES FTR-K1 SERIES n SAFETY STANDARDS 12A type Type UL Compliance UL 508 E63614 Contact rating FTR-K1AK ( ) (W)(MA, MB) Flammability: UL 94-VII (plastics) 16A, 24VAC (resisitive) 16A, 277 VAC (resisitive) 1 /2HP, 277VAC 1/3 HP, 125VAC Pilot duty: B300 FTR-K1(A, C)K ( ) (W)(MA, MB) 12A, 277VAC/24VDC (resisitive) 16A, 277 VAC/24VDC (resisitive) 1 /2HP, 277VAC 1/3 HP, 125VAC Pilot duty: B300 FTR-K1(A, C)K ( ) (W)(MA, MB) 12A, 250 VAC (cosØ=1) 85˚C 16A, 250 VAC (cosØ=1) 85˚C 12 A 24VDC (0ms) 16 A 24VDC (0ms) 3.5A, 250 VAC (cosØ=0.4) 85˚C 12A, 24VAC (resisitive) 16A, 277 VAC (resisitive) 1 /2HP, 277VAC 1/3 HP, 125VAC 1/8 HP, 125VAC Pilot duty: B300 FTR-K1CK ( ) (W)(MA, MB) CSA C22.2 No. 14 LR 40304 VDE 0435, 0631, 0700, 0860 40013848 SEMKO EN 61058-1:1992 and A1 250VAC, 12 (3)A 40T70 EN 61095:1993 and A1+A11 Complies with NEMKO, DEMKO, FIMKO n SAFETY STANDARDS 10A type Type UL Compliance UL 508 E63614 CSA C22.2 No. 14 LR 40304 Contact rating FTR-K1AL( ) (W,E)(LA, LB)-RG Flammability: UL 94-VII (plastics) FTR-K1AL( ) (W)(LA, LB) 10A, 277 VAC (resistive) 1 /2HP, 125VAC 1/3 HP, 277VAC Pilot duty: B300 FTR-K1CL ( )W-LA 10A, 277VAC (resistive) FTR-K1 AL( )W-(LA, LB) 10A, 250 VAC, 150,000 cycles LA: 85ºC, LB:85ºC 3A, 250 VAC (cosØ=0.4) 100,000 cycles LA: 85ºC, LB:85ºC FTR-K1CL ( )W-LA 10A, 250 VAC, 100,000 cycles 85ºC VDE 0435, 0631, 0700, 0860 40013848 SEMKO EN 61058-1:1992 and A1 250VAC, 10 (3)A 40T85 (-LA) EN 61095:1993 and A1+A11 250VAC, 10 (3)A 40T85 (-LB) Complies with NEMKO, DEMKO, FIMKO 9 FTR-K1 SERIES FTR-K1 SERIES n CHARACTERISTIC DATA 10 FTR-K1 SERIES FTR-K1 SERIES  FTR-K1 SERIES FTR-K1 SERIES n DIMENSIONS l Dimensions FTR-K1 ( ) / LB Schematics (BOTTOM VIEW) l l PC board mounting hole layout (BOTTOM VIEW) l Dimensions FTR-K1 ( ) MA / LA Schematics (BOTTOM VIEW) l l PC board mounting hole layout (BOTTOM VIEW) l Dimensions FTR-K1 ( ) / MB Schematics (BOTTOM VIEW) l l PC board mounting hole layout (BOTTOM VIEW) * terminals ommited in case of 1 form A version Unit: mm 12 FTR-K1 SERIES FTR-K1 SERIES RoHS Compliance and Lead Free Information 1. General Information All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. l Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) l All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf l Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. l 2. Recommended Lead Free Solder Profile l Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder condition: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C solder bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 4. Tin Whiskers l 13 FTR-K1 SERIES FTR-K1 SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://us.fujitsu.com/components Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ ©2009 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. December 1, 2009 14