MZF-12WHG-K

MINIATURE RELAY 1 POLE—1 to 2 A (FOR SIGNAL SWITCHING) MZ SERIES n FEATURES l l l l RoHS compliant l l l l Subminiature size Standard and high sensitivity types available UL, CSA recognized FCC rules and regulations part 68 —Dielectric strength 1,500 V between coil and contacts High reliability-bifurcated contacts available DIL pitch terminals Plastic sealed type RoHS compliant since date code: 0437L2 Please see page 6 for more information n ORDERING INFORMATION [Example] (a) (b) (c) (d) (e) (f ) (g) MZ F – 12 (a) (b) (c) W (d) HG – K – U (e) (f ) (g) MZ : MZ Series Nil : Standard type F : High dielectric strength type Refer to the COIL DATA CHART Nil : 1 A single D : 2 A single (without MZF) W : 1 A bifurcated type HG : Standard type (without MZ-D) (450-500mW) HS : High sensitivity type (without MZF/MZ-D) (190-270mW) Nil : Flux free type K : Plastic sealed type Nil : Non UL, • CSA approved type U : UL • CSA approved type Series Name Dielectric Function Nominal Voltage Contact Coil Type Enclosure UL, CSA Standard Note: For movable and stationary contact with gold overlay type, add suffix “–OH”. 1 MZ SERIES n COIL DATA CHART MODEL Single 2 A Type MZ-1.5D-(K) MZ- 3 D-(K) Standard Type MZ-4.5D-(K) MZ- 5 D-(K) MZ- 6 D-(K) MZ- 9 D-(K) MZ-12 D-(K) MZ-18 D-(K) MZ-24 D-(K) MZ-48 D-(K) 1 A Type MZ (F)-1.5HG-(K) MZ (F)- 3 HG-(K) MZ (F)-4.5HG-(K) MZ (F)- 5 HG-(K) MZ (F)- 6 HG-(K) MZ (F)- 9 HG-(K) MZ (F)-12 HG-(K) MZ (F)-18 HG-(K) MZ (F)-24 HG-(K) MZ (F)-48 HG-(K) MZ-1.5HS-(K) MZ- 3 HS-(K) High Sensitivity Type MZ-4.5HS-(K) MZ- 5 HS-(K) MZ- 6 HS-(K) MZ- 9 HS-(K) MZ-12 HS-(K) MZ-15 HS-(K) MZ-18 HS-(K) MZ-24 HS-(K) MZ-48 HS-(K) Bifurcated 1 A Type MZ-1.5WHG-(K) MZ- 3 WHG-(K) MZ-4.5WHG-(K) MZ- 5 WHG-(K) MZ- 6 WHG-(K) MZ- 9 WHG-(K) MZ-12 WHG-(K) MZ-18 WHG-(K) MZ-24 WHG-(K) MZ-48 WHG-(K) MZ-1.5WHS-(K) MZ- 3 WHS-(K) MZ-4.5WHS-(K) MZ- 5 WHS-(K) MZ- 6 WHS-(K) MZ- 9 WHS-(K) MZ-12 WHS-(K) MZ-15 WHS-(K) MZ-18 WHS-(K) MZ-24 WHS-(K) MZ-48 WHS-(K) 1.5 VDC 3 VDC 4.5 VDC 5 VDC 6 VDC 9 VDC 12 VDC 18 VDC 24 VDC 48 VDC 1.5 VDC 3 VDC 4.5 VDC 5 VDC 6 VDC 9 VDC 12 VDC 15 VDC 18 VDC 24 VDC 48 VDC Nominal voltage Coil resistance (±10%) 5Ω 20 Ω 45 Ω 56 Ω 80 Ω 180 Ω 320 Ω 720 Ω 1,280 Ω 4,600 Ω 12 Ω 45 Ω 100 Ω 120 Ω 180 Ω 400 Ω 700 Ω 1,100 Ω 1,600 Ω 2,800 Ω 8,500 Ω Must operate voltage 1.05 VDC 2.1 VDC 3.15 VDC 3.5 VDC 4.2 VDC 6.3 VDC 8.4 VDC 12.6 VDC 16.8 VDC 33.6 VDC 1.05 VDC 2.1 VDC 3.15 VDC 3.5 VDC 4.2 VDC 6.3 VDC 8.4 VDC 10.5 VDC 12.6 VDC 16.8 VDC 33.6 VDC Must release voltage 0.08 VDC 0.15 VDC 0.23 VDC 0.25 VDC 0.3 VDC 0.45 VDC 0.6 VDC 0.9 VDC 1.2 VDC 2.4 VDC 0.08 VDC 0.15 VDC 0.23 VDC 0.25 VDC 0.3 VDC 0.45 VDC 0.6 VDC 0.75 VDC 0.9 VDC 1.2 VDC 2.4 VDC Nominal power 450 mW 450 mW 450 mW 450 mW 450 mW 450 mW 450 mW 450 mW 450 mW 500 mW 190 mW 200 mW 200 mW 200 mW 200 mW 200 mW 200 mW 200 mW 200 mW 200 mW 270 mW Note: All values in the table are measured at 20°C. 2 MZ SERIES n SPECIFICATIONS Standard Item MZ-( ) D Contact Arrangement Material Resistance (initial) Rating (resistive) Maximum Carrying Current Maximum Switching Power Maximum Switching Voltage Maximum Switching Current Minimum Switching Load* Capacitance (at 10 MHz) Coil Nominal Power (at 20°C) Operate Power (at 20°C) Operating Temperature Time Value Life Operate (at nominal voltage) Release (at nominal voltage) Mechanical Electrical (at rating) Gold-overlay silver-nickel 2 A 24 VDC 1 A 120 VAC 2A 120 VA/48 W 2A 1 mA 1 VDC 60 AV/24 W 1A 0.1 mA 100 mVDC 1 mA 1 VDC 0.1 mA 100 mVDC 120 VAC, 60 VDC Single 1 form C (SPDT) Gold overlay silver-palladium Bifurcated MZ-( ) HG MZ-( ) WHG High Sensitivity Type Single MZ-( ) HS Bifurcated MZ-( ) WHS Maximum 100 mΩ (at 1 A 6 VDC) 1 A 24 VDC 0.5 A 120 VAC Approximately 0.8 pF (between open contacts, adjacent contacts) Approximately 7.5 pF (between coil and contacts) 450 to 500 mW 220 to 250 mW –30°C to +55°C (no frost) Maximum 6 ms Maximum 3 ms 2 × 107 operations minimum 1 A 120 VAC 0.5 A 120 VAC 2 × 105 operations minimum 1 × 105 ops. min. 1 A 24 VAC 5 × 105 operations minimum 2 A 24 VDC 2 × 105 ops. min. 10 to 55 Hz (double amplitude of 3.28 mm) 10 to 55 Hz (double amplitude of 3.28 mm) 100 m/s2 (11±1 ms) 1,000 m/s2 ( 6±1 ms) Approximately 3.5 g 190 to 270 mW 100 to 130 mW –30°C to +75°C Other Vibration Misoperation Resistance Endurance Shock Misoperation Resistance Endurance Weight *1 Minimum switching loads mentioned above are reference values. Please perform the confirmation test with the actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 3 MZ SERIES n INSULATION Item Isolation (initial) Dielectric Strength Surge Voltage open contacts coil and contacts Single Minimum 100 MΩ (at 500VDC) Standard: 500VAC 1 min., High isolation: 1,000VAC 1 min. Standard: 500VAC 1 min., High isolation: 1,500VAC 1 min. 1500V (coil-contact) (1/40 µs standard wave) n SAFETY STANDARDS AND FILE NUMBERS Type UL Compliance UL 508 UL 60950-1 E 45026 Contact rating Flammability: UL 94-V0 (plastics) [1A] 0.5A, 120VAC (resistive) 1A, 24VDC (resistive) [2A] 1A, 120VAC (resistive) 2A, 30VDC (resistive) CSA C22.2 No. 14 LR 35579 n CHARACTERISTIC DATA 0.1 0.3 0.5 4 MZ SERIES n REFERENCE DATA 5 MZ SERIES n DIMENSIONS l Dimensions MZ (F) type (Flux free type) l Schematics (Bottom View) l PC board mounting hole layout (Bottom View) MZ (F)-K type (Plastic sealed type) Unit: mm 6 MZ SERIES RoHS Compliance and Lead Free Relay Information 1. General Information Relays produced after the specific date code that is indicated on each data sheet are lead-free now. Most of our signal and power relays are lead-free. Please refer to Lead-Free Status Info. (http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf) l Lead free solder paste currently used in relays is Sn-3.0Ag-0.5Cu. l All signal and most power relays also comply with RoHS. Please refer to individual data sheets. Relays that are RoHS compliant do not contain the 5 hazardous materials that are restricted by RoHS directive (lead, mercury, chromium IV, PBB, PBDE). l It has been verified that using lead-free relays in leaded assembly process will not cause any problems (compatible). l “LF” is marked on each outer and inner carton. (No marking on individual relays). l To avoid leaded relays (for lead-free sample, etc.) please consult with area sales office. l We will ship leaded relays as long as the leaded relay inventory exists. Note: Cadmium was exempted from RoHS on October 21, 2005. (Amendment to Directive 2002/95/EC) l 2. Recommended Lead Free Solder Profile l Recommended solder paste Sn-3.0Ag-0.5Cu. Reflow Solder condition Flow Solder condition: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C soler bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical realys. Dipped SnAgCu solder is known as low risk tin whisker. No considerable length whisker was found by our in house test. 4. Tin Whisker l 7 MZ SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://www.fujitsu.com/us/services/edevices/components/ Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ ©2008 Fujitsu Components America, Inc. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. Fujitsu Components America or its affiliates do not warrant that the content of datasheet is error free. In a continuing effort to improve our products Fujitsu Components America, Inc. or its affiliates reserve the right to change specifications/datasheets without prior notice. Rev. January 9, 2008. 8