NY-12W-K

FTR-K1 SERIES POWER RELAY 1 POLE - 5A Slim Type NY Series n FEATURES Slim type with 5 mm thickness - Suited for high density mounting l Low power consumption and high sensitivity - Nominal coil power: 120 mW - Operating power: 54 mW l UL and CSA recognized l High insulation - Surge voltage: 5,080V - Dielectric strength: 3,000VAC (coil and contacts) l SIL pitch terminals l Plastic sealed type, RTIII l Compatible with solid state I/O module type SN in size and pin (terminal) arrangement l Environmentally friendly cadmium free contact type l RoHS compliant. Please see page 6 for more information l n PARTNUMBER INFORMATION [Example] (a) NY P - 12 W - K - IE (a) (b) (*) (c) (d) (e) (*) (f ) Relay type (b) Mounting type NY : NY-Series Nil P : PCB board mounting type : Socket mounting type (c) Coil rated voltage 12 : 4.5.....24 VDC Coil rating table at page 3 (d) Contact design W : Bifurcated contact (e) Enclosure K : Plastic sealed type, RTIII (f) Insulation IE : Conform to IEC standard Note: Actual marking omits the hyphen (-) and IE of (*) 1 FTR-K1NY SERIES SERIES n SPECIFICATION Item Contact Data NY Configuration 1 form A (SPST-NO) Construction Bifurcated Material Gold overlay silver alloy (AgNi + Au) Resistance (initial) Max. 30 mΩ at 6 VDC, 1 A Contact rating 5A, 250VAC / 30VDC Max. carrying current 5A Max. switching voltage 270VAC / 125 VDC Max. switching power 750VA / 90W Max. switching current 5A Min. switching load * 1 mA, 5 VDC Mechanical Min. 20 x 106 operations Electrical Min. 100 x 103 operations (at 3A, 250VAC, 30VDC resistive) Min. 50 x 103 operations (at 5A, 250VAC, 30VDC resistive) Rated power (at 20 °C) 120 mW Operate power (at 20 °C) 54 mW Operating temperature range -40 °C to +90 °C (no frost) Timing Data Operate (at nominal voltage) Max. 10 ms (without bounce) Release (at nominal voltage) Max. 5 ms (without bounce) Insulation Resistance (initial) Min. 1,000MΩ at 500VDC Life Coil Data Dielectric strength Surge strength Open contacts 750VAC, 1min Contacts to coil 3,000VAC, 1min Coil to contacts 5,080V / 1.2 x 50µs standard wave Clearance Min. 3mm Creepage Min. 3mm Other Remarks / Conditions Misoperation 10 to 55 to 10Hz single amplitude 0.75mm Coil ON/OFF, 3 axes, total 6 cycles Endurance 10 to 55 to 10Hz single amplitude 0.25mm Coil OFF, 3 axes, total 6 hours Misoperation Min. 100m/s² (11 ± 1ms) Coil ON/OFF, 3 axes, total 36 operations Endurance Min. 1,000m/s² (6 ± 1ms) Coil OFF, 3 axes, total 18 operations Vibration resistance Shock Weight Approximately 3.5 g Sealing Plastic sealed, RTIII * Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 2 FTR-K1NY SERIES SERIES n COIL RATING Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must ReleaseVoltage (VDC) * 4.5 4.5 169 3 0.45 5 5 208 3.35 0.5 6 6 300 4 0.6 9 9 675 6 0.9 12 12 1,200 8 1.2 18 18 2,700 12.1 1.8 24 24 4,800 16.1 2.4 Rated Power (mW) 120 Note: All values in the table are valid for 20°C and zero contact current. * Specified operate values are valid for pulse wave voltage. Please use at rated coil voltage. Please refer to characteristic data and set up adequate voltage in case of use at over voltage. n SAFETY STANDARDS Type Compliance Contact rating UL UL 508 ANSI/ISA12.12.01 E56140, E199193 Flammability: UL 94-V0 (plastics) CSA C22.2 No. 14 LR 35579 3A, 250VAC/30VDC (General use) 5A, 250VAC/30VDC (resistive) 1/8 HP, 250VAC /125VAC Pilot duty: C300, D150, R300 3 FTR-K1NY SERIES SERIES n CHARACTERISTIC DATA (Characteristic data is not guaranteed value but measured values of samples from production line.) Coil temperature rise Timing 動作時間 3A 接点3A通電 0A 接点無通電 復帰時間 0.1 0.2 0.1Coil power (W) 0.2 コイル印加電力（W） 0.3 0.3 0 0 5 5 3 23 DC抵抗負荷 DC resistive 0.5 0.3 0.3 0.2 0.2 0.1 100 200 0.110 20 30 50 　接点電圧（ V） 100 200 10 20 30 50 Contact voltage (V) 0.1 0.1 0.2 0.3 Coil0.2 power (W)0.3 コイル印加電力（W） 3 5 2 3 2 0.1 0.1 Distribution of operate/release voltage DC30 V L/R＝40ms 30VDC L/R=40ms DC100～120 V L/R＝7～40ms 0.2 0.3 0.5 0.7 1 2 接点電流（ 0.2 0.3 0.5 0.7 1 A）2 3 3 NY-12W-K n =100 50 60 40 60 70 0 80 1 Voltage (V) Release 4 2 3 4 5 6 7 Initial 100 200 Make 500 Operation (x10 4 ) Make 60 40 8 0 10 1000 2000 20 30 40 50 60 Electrical life test 20 16 Operate 12 Release 8 4 NY-24W-K n=10 1200 operation/min. 100 NY-12W-K n =100 Electrical life test 16 8 80 Time (ms) Mechanical life test 20 Operate 60 20 Nominal voltage multiplying factor (%) 12 40 周囲温度（℃） 80 Operate time Release time Voltage (V) 40 20 Distribution of contact resistance 20 20 30 il) （ e (cool co 感動電圧 ate voltag ） Must oper ルコイル ク 圧（ ー 感 20 40動電 60 80 100 5 5 Distribution (%) Distribution (%) 40 20 イル） ホットコ 100 80 Operate voltage Release voltage 10 ot coil) ltage (h erate vo Must op 1.0 0.8 0.8 0.6 Distribution of operate/release time NY-12W-K n =100 0 1.4 1.2 1.2 1.0 0 100 60 電 Contact current (A) 100 80 電 0A 通 DC30 V/AC240 V 抵抗負荷 30VDC/240VAC resistive 20 104 30 回 20 ） 10 10 5 500 500 3A Life curve 寿 100 命 50 （ 30 × 50 300 300 点 1.8 1.6 1.6 1.4 0.6 0 0.4 0.4 接 接 5A 点 5A 通 AC120 V抵抗負荷 DC30 Vresistive L/R＝7 ms 120VAC 30VDCAC120 L/R=7ms V COSφ＝0.4 AC240 V COSφ＝0.4 300 200 300 200 100 AC抵抗負荷 AC resistive Operation (x10 4 ) Contact current (A) 電 圧 に 対 す る 比 率 10 Release 接 点 2 電 1 流 1 （A） 0.5 Voltage (V) Nominal voltage multiplying factor Time (ms) Operate 3A 2.4 2.4 2.2 2.0 定 2.2 格 2.0 1.8 接点5A通電 コ イ ル 20 温 度 20 上 昇 （℃） 10 Maximum switching power Distribution (%) 5A 30 30 0 0 0 200 100 50 20 10 5 Operating range 40 40 電 通 無 点 接 16 16 14 14 12 12 10 10 8 時 間 8 （ms） 6 6 4 4 2 2 0 200 100 50 20 10 5 20 16 Operate 12 Release 8 4 NY-24W-K n=10 30 operation/min. 240VAC, 3A (resistive) Initial 1 2 Make 5 Operation (x10 4 ) 10 NY-24W-K 0 n=10 200 30 operation/min. 100 30VDC, 3A (resistive) 50 20 10 5 Initial 1 2 Make 5 10 Operation (x10 4 ) 4 FTR-K1NY SERIES SERIES n DIMENSIONS NY type l Dimensions l Schematics l PC board mounting hole layout (BOTTOM VIEW) l Schematics l PC board mounting hole layout (BOTTOM VIEW) NYP type l Dimensions Socket type JL-5N l Dimensions l PC board mounting hole layout (BOTTOM VIEW) Unit: mm Note: Tolerance for PC board mounting hole/pad layout: +/-0.1. Note: Dimensions of the terminals do not include thickness of pre-solder. Note: This datasheet provide only + tolerance for outer dimensions. Please ask for specification in case you need other tolerances. 5 FTR-K1NY SERIES SERIES Cautions • • • • All values mentioned in this datasheet are provided under ideal conditions. Please perform the confirmation test before actual use. Reflow soldering is prohibited. Do not use relays in the atmosphere with sulfide gas, chloride gas or nitric oxide. Contact resistance may increase. Do not use silicon or silicon-containing product or materials near relays. It may cause contact failure. RoHS Compliance and Lead Free Information 1. General Information • • • • All relays produced by Fujitsu Components are compliant with RoHS directive 2011/65/EU including amendments. Cadmium as used in electrical contacts is exempted from the RoHS directives. As per Annex III of directive 2011/65/EU. All relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/ downloads/MICRO/fcai/relays/lead-free-letter.pdf Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. 2. Recommended Lead Free Solder Condition • Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder Condition: Solder by Soldering Iron: Pre-heating: maximum 120˚C within 90 sec Soldering Iron: 30-60W Soldering: dip within 5 sec. at 255˚C ± 5˚C solder bath Temperature: maximum 350-360˚C Duration: maximum 3 sec. Relay must be cooled by air immediately after soldering We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity • Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers • Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 6 FTR-K1NY SERIES SERIES Fujitsu Components International Headquarter Offices Japan FUJITSU COMPONENT LIMITED Shinagawa Seaside Park Tower 19F, 12-4, Higashi-shinagawa 4-chome, Shinagawa-ku, Tokyo,140-0002, Japan Tel: (81-3) 3450-1682 Fax: (81-3) 3474-2385 Email: fcl-contact@cs.jp.fujitsu.com Web: www.fujitsu.com/jp/fcl/ Asia Pacific FUJITSU COMPONENTS ASIA, LTD. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components North and South America FUJITSU COMPONENTS AMERICA, INC 2290 North First Street, Suite 212 San Jose, CA 95131, USA Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: us.fujitsu.com/components China FUJITSU ELECTRONIC COMPONENTS (SHANGHAI) CO., LTD. Unit 4306, InterContinental Center 100 Yu Tong Road, Shanghai 200070, China Tel: (86-21) 3253 0998 Fax: (86-21) 3253 0997 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components Europe FUJITSU COMPONENTS EUROPE B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: www.fujitsu.com/uk/components Hong Kong FUJITSU COMPONENTS HONG KONG CO., LTD Unit 506, Inter-Continental Plaza No.94 Granville Road, Tsim Sha Tsui, Kowloon, Hong Kong Tel: (852) 2881-8495 Tex: (852) 2894-9512 Email: fcal@sg.fujitsu.com Web: www.fujitsu.com/sg/products/devices/components/ Korea FUJITSU COMPONENTS KOREA LIMITED Alpha Tower #403, 645 Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, 13524 Korea Tel: (82) 31-708-7108 Fax: (82) 31-709-7108 Email: fcal@sg.fujitsu.com www.fujitsu.com/sg/products/devices/components/ ©2018 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users’ own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. September 11, 2018 7