FEP30GP

FEP30AP THRU FEP30JP FAST EFFICIENT PLASTIC RECTIFIER Reverse Voltage - 50 to 600 Volts TO-247AD 0.645 (16.4) 0.625 (15.9) 0.203 (5.16) 0.193 (4.90) 0.245 (6.2) 0.225 (5.7) 0.323 (8.2) 0.313 (7.9) 10o 30o 0.078 REF (1.98) Forward Current - 30.0 Amperes FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ Dual rectifier construction, positive center-tap ♦ Glass passivated chip junctions ♦ Superfast recovery times for high efficiency ♦ Low forward voltage, high current capability ♦ Low thermal resistance ♦ Low power loss ♦ High temperature soldering guaranteed: 250°C, 0.16” (4.06mm) from case for 10 seconds 0.170 (4.3) 0.840 (21.3) 0.820 (20.8) 10o TYP. BOTH SIDES 0.142 (3.6) 0.138 (3.5) 1 2 3 0.086 (2.18) 0.076 (1.93) 1o REF. BOTH SIDES 0.118 (3.0) 0.108 (2.7) 0.127 (3.22) 0.160 (4.1) 0.140 (3.5) 0.795 (20.2) 0.775 (19.6) 0.117 (2.97) MECHANICAL DATA 0.048 (1.22) 0.225 (5.7) 0.205 (5.2) 0.044 (1.12) 0.030 (0.76) 0.020 (0.51) PIN 2 CASE PIN 1 PIN 3 Dimensions in inches and (millimeters) Case: JEDEC TO-247AD molded plastic body over passivated chips Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting Position: Any Mounting Torque: 10 in. - lbs. max. Weight: 0.22 ounce, 6.3 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS FEP 30AP FEP 30BP FEP 30CP FEP 30DP FEP 30FP FEP 30GP FEP 30HP FEP 30JP UNITS Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TC=100°C Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) at TC=100°C Maximum instantaneous forward voltage per leg at 15.0A Maximum DC reverse current at rated DC blocking voltage TC=25°C TC=100°C VRRM VRMS VDC I(AV) 50 35 50 100 70 100 150 105 150 200 140 200 300 210 300 30.0 400 280 400 500 350 500 600 420 600 Volts Volts Volts Amps IFSM 300.0 Amps VF IR trr CJ RΘJC TJ, TSTG 0.95 10.0 500.0 35.0 175.0 1.0 1.3 1.5 Volts µA Maximum reverse recovery time time (NOTE 1) per leg Typical junction capacitance per leg (NOTE 2) Typical thermal resistance (NOTE 3) Operating storage and temperature range 50.0 145.0 ns pF °C/W °C -55 to +150 NOTES: 1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to case per leg mounted on heatsink 4/98 RATINGS AND CHARACTERISTIC CURVES FEP30AP THRU FEP30JP FIG. 1 - FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT, AMPERES FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG 36 30 24 12 6.0 0 300 PEAK FORWARD SURGE CURRENT, AMPERES RESISTIVE OR INDUCTIVE LOAD 250 200 150 100 50 0 TC=100°C 8.3ms SINGLE HALF SINE WAVE (JEDEC Method) 0 50 100 150 CASE TEMPERATURE, °C 1 10 NUMBER OF CYCLES AT 60 HZ 100 FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG 40 INSTANTANEOUS FORWARD CURRENT, AMPERES PULSE WIDTH=300µs 1% DUTY CYCLE TJ=125°C FIG. 4 - TYPICAL REVERSE CHARACTERISTICS PER LEG 1,000 10 INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES 100 TJ=25°C 1 50-200V 300-400V 500-600V 25 TJ= °C 10 100 °C 0.1 0.2 TJ= 0.4 0.6 0.8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 1 50-200V 300-600V 25 TJ= °C FIG. 5 - TYPICAL JUNCTION CAPACITANCE 1,000 JUNCTION CAPACITANCE, pF 0.1 0 20 40 60 80 100 TJ=25°C f=1.0 MHZ Vsig=50mVp-p PERCENT OF RATED PEAK REVERSE VOLTAGE, % 100 50-400V 500-600V 10 0.1 1 10 100 REVERSE VOLTAGE, VOLTS