SRP600A

SRP600A THRU SRP600K FAST SWITCHING PLASTIC RECTIFIER Reverse Voltage - 50 to 800 Volts Case Style P600 Forward Current - 6.0 Amperes FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ High surge current capability ♦ Construction utilizes void-free molded plastic technique ♦ Fast switching for high efficiency ♦ High temperature soldering guaranteed: 250°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension 1.0 (25.4) MIN. 0.360 (9.1) 0.340 (8.6) 0.360 (9.1) 0.340 (8.6) MECHANICAL DATA 0.052 (1.32) 0.048 (1.22) DIA. 1.0 (25.4) MIN. Case: Void-free molded package body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.07 ounce, 2.1 grams Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS SRP 600A SRP 600B SRP 600D SRP 600G SRP 600J SRP 600K UNITS Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current 0.375" (9.5mm) lead length at T A=55°C Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage at 6.0A Maximum DC reverse current at rated DC blocking voltage Maximum reverse recovery time (NOTE 1) Typical junction capacitance (NOTE 2) Typical thermal resistance (NOTE 3) Operating junction temperature range Storage temperature range TA=25°C TA=100°C VRRM VRMS VDC I(AV) 50 35 50 100 70 100 200 140 200 6.0 400 280 400 600 420 600 800 560 800 Volts Volts Volts Amps IFSM VF IR trr CJ RΘJA TJ TSTG 100 100 150 300.0 1.3 10.0 1.0 150 300.0 10.0 -50 to +125 -50 to +150 200 200 Amps Volts µA mA ns pF °C/W °C °C NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient at 0.375” (9.5mm) lead length, with both leads equally to heat sink 4/98 RATINGS AND CHARACTERISTIC CURVES SRP600A THRU SRP600K FIG. 1 - FORWARD CURRENT DERATING CURVE FIG. 2 - FORWARD CURRENT DERATING CURVE 7.0 AVERAGE FORWARD CURRENT, AMPERES 6.0 5.0 4.0 3.0 2.0 1.0 AVERAGE FORWARD CURRENT, AMPERES RESISTIVE OR INDUCTIVE LOAD CAPACITIVE Ipk/IAV = π LOADS 5.0 = Ipk/IAV 10 20 20 16 12 8 4 0 75 L=0 RESISTIVE OR INDUCTIVE LOAD L=LEAD LENGTH .12” (3.2 mm ) L=0.2 L=0.3 5”(6.3 mm) m) 1.6 x 1.6 x 0.04” (40 x 40 x 1mm) COPPER HEAT SINKS 75”( 9.5m L=0.62”( 15.9mm ) 0 20 1.1 x 1.1” (30 x 30mm) COPPER PADS 40 60 80 100 120 140 160 180 80 85 90 95 100 105 110 115 120 125 AMBIENT TEMPERATURE, °C LEAD TEMPERATURE, °C FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 3 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, AMPERES 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 100 INSTANTANEOUS FORWARD CURRENT, AMPERES 400 350 TJ=25°C TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 10 300 250 TJ=125°C 200 150 100 1 1 10 NUMBER OF CYCLES AT 60 HZ 100 0.1 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 5 - TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, MICROAMPERES RΘJL, THERMAL RESISTANCE FROM JUNCTION TO LEAD,°C/W FIG. 6 - TYPICAL THERMAL RESISTANCE 10 TJ=100°C 25 L=LEAD LENGTH 20 15 10 5.0 0 COPPER HEATSINKS 1 TJ=50°C 0.1 TJ=25°C 0.01 0 20 40 60 80 100 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 PERCENT OF RATED PEAK REVERSE VOLTAGE, % EQUAL LEAD LENGTHS TO HEAT SINK, INCHES