UGF18CCT

NEW PRODUCT NEW PRODUCT NEW PRODUCT UGF18ACT THRU UGF18DCT ULTRAFAST EFFICIENT PLASTIC RECTIFIER Reverse Voltage - 50 to 200 Volts ITO-220AB Forward Current - 18.0 Amperes FEATURES ♦ Plastic package has Underwriters Laboratories Flammability Classification 94V-0 ♦ Ideally suited for use in very high frequency switching power supplies, inverters and as a free wheeling diode ♦ Ultrafast 25 nanosecond reverse recovery times ♦ Soft recovery characteristics ♦ Excellent high temperature switching ♦ Glass passivated junctions ♦ High temperature soldering guaranteed: 250°C, 0.25" (6.35mm) from case for 10 seconds 0.405 (10.27) 0.383 (9.72) 0.188 (4.77) 0.172 (4.36) 0.110 (2.80) 0.100 (2.54) 0.140 (3.56) DIA. 0.130 (3.30) 0.131 (3.39) DIA. 0.122 (3.08) 0.600 (15.5) 0.580 (14.5) PIN 1 2 3 0.670 (17.2) 0.646 (16.4) 0.350 (8.89) 0.330 (8.38) 0.191 (4.85) 0.171 (4.35) 0.560 (14.22) 0.530 (13.46) 0.060 (1.52) 0.110 (2.80) 0.100 (2.54) MECHANICAL DATA 0.037 (0.94) 0.027 (0.69) 0.105 (2.67) 0.095 (2.41) 0.022 (0.55) 0.014 (0.36) PIN 1 PIN 3 PIN 2 0.205 (5.20) 0.195 (4.95) Dimensions in inches and (millimeters) Case: JEDECITO-220AB molded plastic body Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting Position: Any Weight: 0.08 ounce, 2.24 grams Mounting Torque: 5 in. - lbs. max. MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS UGF18ACT UGF18BCT UGF18CCT UGF18DCT UNITS Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TC=105°C Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) per leg at TC=105°C Maximum instantaneous forward voltage per leg at 9.0A 20A 5.0A, TJ=100°C Maximum DC reverse current TA=25°C at rated DC blocking voltage per leg TA=100°C Maximum reverse recovery time (NOTE 1) Maximum reverse recovery time TJ=25°C TJ=100°C (NOTE 2) Maximum recovered stored charge TJ=25°C TJ=100°C (NOTE 2) Typical junction capacitance (NOTE 3) Typical thermal resistance (NOTE 4) Operating junction and storage temperature range NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) trr and Qrr measured at: IF=9.0A, VR=30V, di/dt=50A/µs, Irr=10% IRM (3) Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts (4) Thermal resistance from junction to case per leg VRRM VRMS VDC I(AV) IFSM 50 35 50 100 70 100 18.0 175.0 1.10 1.20 0.95 10.0 300.0 20.0 30.0 50.0 20.0 45.0 30.0 4.0 150 105 150 200 140 200 Volts Volts Volts Amps Amps VF IR trr trr Qrr CJ RΘJC TJ, TSTG Volts µA ns ns nC pF °C/W °C -65 to +150 4/98 RATINGS AND CHARACTERISTIC CURVES UGF18ACT THRU UGF18DCT FIG. 1 -FORWARD CURRENT DERATING CURVE FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG 24 AVERAGE FORWARD CURRENT, AMPERES RESISTIVE OR INDUCTIVE LOAD 1,000 PEAK FORWARD SURGE CURRENT, AMPERES 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) TC=105°C 20 16 12 8.0 4.0 0 100 0 25 50 75 100 125 150 175 CASE TEMPERATURE, °C 10 1 10 NUMBER OF CYCLES AT 60 HZ 100 INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG INSTANTANEOUS FORWARD CURRENT, AMPERES FIG. 4 - TYPICAL REVERSE CHARACTERISTICS PER LEG 100 1,000 TJ=125°C 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 100 TJ=100°C 10 1 1 TJ=25°C 0.1 0.1 0.01 0.4 0.01 0.6 0.8 1.0 1.2 1.4 1.6 0 20 40 60 80 100 INSTANTANEOUS FORWARD VOLTAGE, VOLTS PERCENT OF RATED PEAK REVERSE VOLTAGE, % FIG. 5 - REVERSE SWITCHING CHARACTERISTICS PER LEG FIG. 6 - TYPICAL JUNCTION CAPACITANCE PER LEG 60 STORED CHARGE/REVERSE RECOVERY TIME, nC/ns 100 IF=9.0A VR=30V 50 40 30 20 di/dt=20A/µs di/dt=50A/µs di/dt=100A/µs di/dt=50A/µs di/dt=150A/µs JUNCTION CAPACITANCE, pF di/dt=100A/µs TJ=125°C f=1.0 MHz Vsig=50MVp-p 10 di/dt=20A/µs 10 0 trr Qrr 0 25 50 75 100 125 150 175 JUNCTION TEMPERATURE, °C 1 0.1 1 10 100 REVERSE VOLTAGE, VOLTS