C7021

IMAGE SENSOR CCD multichannel detector head C7020, C7021, C7025 Designed for front-illuminated CCD area image sensors C7020, C7021 and C7025 are high sensitivity multichannel detector heads for use with front-illuminated FFT-CCD area image sensors. C7020 is designed for the non-cooled front-illuminated CCD image sensors (S7010 series), while C7021 and C7025 for the TE-cooled CCD image sensors (S7011/S7015 series) for detection at even lower light levels. C7020, C7021 and C7025 incorporate a low-noise driver/amplifier circuit that provide reliable operation from simple external signals. C7021 and C7025 also include a highly stable temperature controller that cools the sensor to a preset temperature level (Ts= -10 ˚C) as soon as the power is turned on. If the cooler fails and causes internal circuitry to overheat, the builtin protection circuit automatically turns off the power to the thermoelectric cooler. Despite its compact size, the housing configuration is designed for good heat dissipation, and threaded mounting holes on the front panel allow connections to other devices such as monochrometers. The table below shows front-illuminated CCD image sensors for C7020, C7021 and C7025. C7020, C7021 and C7025 do not come with a CCD image sensor, so select the desired sensor and order it separately. Multichannel detector head controller C7310-02 is also available. Features C7020: for non-cooled type C7021, C7025: for TE-cooled types l Binning operation *2 l Driver/amplifier circuit for low noise CCD operation l Highly stable temperature controller (C7021, C7025) Cooling temperature: fixed at -10 ± 0.05 ˚C (Ta=10 to 35 ˚C) l Simple signal input operation l Compact configuration Applications 1 l Designed for front-illuminated CCD area image sensor * l Fluorescence spectroscopy l Raman spectroscopy l Other low light level detection I Selection guide The table below shows CCD area image sensors applicable for C7020, C7021, C7025. Since C7020, C7021, C7025 do not include a  CCD area image sensor, so select the desired sensor and order it  separately. CCD area image sensor Number of Active area Type No. Number of pixels active pixels [mm (H) × mm (V)] S7010-0906 532 × 64 512 × 60 12.288 × 1.440 S7010-0907 532 × 128 512 × 124 12.288 × 2.976 S7010-0908 532 × 256 512 × 252 12.288 × 6.048 C7020 S7010-1006 1044 × 64 1024 × 60 24.576 × 1.440 S7010-1007 1044 × 128 1024 × 124 24.576 × 2.976 S7010-1008 1044 × 256 1024 × 252 24.576 × 6.048 S7011-0906 532 × 64 512 × 60 12.288 × 1.440 S7011-0907 532 × 128 512 × 124 12.288 × 2.976 C7021 S7011-1006 1044 × 64 1024 × 60 24.576 × 1.440 S7011-1007 1044 × 128 1024 × 124 24.576 × 2.976 S7015-0908 532 × 256 512 × 252 12.288 × 6.048 C7025 S7015-1008 1044 × 256 1024 × 252 24.576 × 6.048 *1: The FFT-CCD (full frame transfer CCD) has charge transfer sections that are also used as light receiving areas, being different from interline transfer CCD (IT-CCD) commonly used in video cameras. Compared to the IT-CCD, the FFT-CCD offers advantages of low dark current, a 100 % open area ratio and low image lag. *2: The FFT-CCD was originally designed as a two-dimensional image sensor. However, it can be operated like a linear image sensor having a large active area by transferring all the pixel signals in the vertical direction to the horizontal register (this is referred to as line binning). Type No. 1 CCD multichannel detector head I Absolute maximum ratings C7020, C7021, C7025 Min. -0.5 0 +10 -20 0 Typ. Max. +7 +18 -18 +30 +7 +7 +14 VD (1, 2) +50 +35 +70 +70 Unit Parameter Supply voltage (for digital circuitry) Supply voltage (for analog circuitry) Supply voltage *3 C7020 C7021, C7025 C7020 C7021, C7025 Digital input voltage Operating temperature Storage temperature Symbol VD1 VA1+ VA1VA2 VD2 Vp VF Topr Tstg V °C I Electrical characteristics (Ta=25 °C, VD1=+5 V, VA1+=+15 V, VA1-= -15 V, VA2=+24 V, VD2=+5 V, Vp=+5 V, VF=+12 V, unless otherwise noted) Parameter Digital input CLK frequency Data video readout frequency Start pulse width Digital output Power supply operating conditions High level Low level Symbol VIH VIL fclk fv tst VIH VIL VD VA1+ VA1VA2 VD2 Vp VF Min. +2.0 -0.5 1/fCLK +2.0 Typ. Max. +VD +0.8 1 fCLK/4 +0.8 Unit V V MHz Hz s V V V V V V V V V mA mA mA mA mA A A A A mA High level (Io= -6 mA) Low level (Io=+6 mA) Digital circuitry Analog circuitry Other VD1 (+5 VDC) VA1+ (+15 VDC) VA1- (-15 VDC) VA2 (+24 VDC) VD2 (+5 VDC) *3 Vp (+5 DC) *3 Ta=10 °C Ta=20 °C Ta=30 °C Ta=35 °C Voltage Current +4.75 +14.5 -14.5 +23.5 +4.75 +4.75 +11.75 - VF (+12 VDC) *3 +5.0 +15.0 -15.0 +24.0 +5.0 +5.0 +12.0 +0.8 +1.4 +1.8 +2.2 +100 +5.25 +15.5 -15.5 +24.5 +5.25 +5.25 +12.25 +200 +100 -100 +30 +30 +2.5 +2.5 +2.5 +2.5 - I Electrical and optical characteristics (Ta=25 °C, Ts= -10 °C, VD1=+5 V, VA1+=+15 V, VA1-= -15 V, VA2=+24 V, VD2=+5 V, Vp=+5 V, VF=+12 V, unless otherwise noted) Parameter Symbol Min. Typ. Max. Unit 400 to Spectral response range nm l 1100 Vertical 150,000 300,000 Full well capacity Fw e Horizontal 300,000 600,000 Conversion gain *4 Sv 15 µV/e 5 Dark current * DS 15 45 e /pixel/s Readout noise Nr 20 e rms Dynamic range DR 30,000 Photo response non-uniformity *6 PRNU ±10 % *3: C7021, C7025 *4: Including the circuit gain. *5: At MPP mode. Vertical register value. The actual value equals the sum of the vertical direction because of the binning operation. *6: Measured at 50 % of the full well capacity. 2 CCD multichannel detector head C7020, C7021, C7025 I Specifications for temperature controller (C7021, C7025) (Ta=25 °C, VD1=+5 V, VA1+=+15 V, VA1-= -15 V, VA2=+24 V, VD2=+5 V, Vp=+5 V, VF=+12 V) Parameter *7 Symbol Min. Typ. Max. Unit Cooling temperature Ts -11 -10 -9 °C Temperature control range -0.05 +0.05 °C DTs Power dissipation of TE-cooler element Pp 7 W Cool down time to reset temperature to 5 min. Setting temperature for overheat protection To +45 °C *7: Other functions include error display, automatic power off, and detection of electrical opens and shorts by the thermosensor. I Spectral response I Dark current vs. temperature 50 (Typ. Ta=25 ˚C) 10000 (Tentative Data) QUANTUM EFFICIENCY (%) 40 DARK CURRENT (e-/pixel/s) 1000 100 30 10 20 1 10 0.1 0 400 500 600 700 800 900 1000 1100 1200 0.01 -50 -40 -30 -20 -10 0 10 20 30 WAVELENGTH (nm) KMPDB0051EA TEMPERATURE (°C) KMPDB0052EA I Block diagram (front-illuminated CCD area image sensor) ( ) IG1V IG2V ISV 23 22 24 SS 20 P1V 15 P2V 14 TG 16 V ...... V=60, 124, 252 H=512, 1024 ...... H 1 RG RD OS 1 2 3 ...... 13 ISH 12 IG1H 4 OD 5 OG 10 11 9 IG2H 2 ISOLATOIN 2 ISOLATOIN P2H P1H 2n SIGNAL OUT 4 OPTICAL 4 OPTICAL 4 BLANK 4 BLANK BLACK BLACK 6 SG KMPDC0015EA 3 CCD multichannel detector head I Block diagram of C7021, C7025 C7020, C7021, C7025 P+ PLED TEMPERATURE CONTROLLER * Vp (+5V) P. GND VD2 (+5V) D. GND TH+ THVF (+12V) F. GND Temp Monitor Cooling Control VD1 (+5V) D. GND VA1+ (+15V) VA1- (-15V) A. GND VA2 (+24V) Start CLK TIMING GENERATOR EOS Trigger Mode Select BUFFER Data Video PRE-AMP INVERTER CLAMP LOW-PASS FILTER TE-COOLER OD RD OG IG1H, IG2H IG1V, IG2V P1V, P2V, TG P1H, P2H SG RG SS, ISV, ISH OS REGULATOR TH.H VDD VEE DRIVER CCD AREA IMAGE SENSOR S7011/S7015 SERIES * C7020 does not include the temperature controller and TE-cooler. CCC KACCC0073EB I Timing chart Start CLK P1V P2V TG P1H P2H SG RG Clamp EOS Trigger Data Video V-ch1 V-ch2 V-ch(M) H-ch1 H-ch2 H-ch10 H-ch11 H-ch(N-10) H-ch(N-9) H-ch(N) M=68, 132, 260 N=532, 1044 V-ch1--V-ch2, V-ch (M-3)--V-ch (M): ISOLATION PIXELS H-ch1--H-ch4, H-ch (N-3)--H-ch (N): BLANK PIXELS H-ch5--H-ch10, H-ch (N-9)--H-ch (N-4): ISOLATION PIXELS KACCC0074EA 4 CCD multichannel detector head I Pin assignment of "SIGNAL I/O" connector 15-pin D-sub connector C7020, C7021, C7025 8 7 6 5 4 3 2 1 15 14 13 12 11 10 9 KACCC0069EA Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Terminal name Mode select Data video VA1+ (+15 V) VA1- (-15 V) VD1 (+5 V) Start CLK EOS A. GND A. GND VA2 (+24 V) D. GND D. GND D. GND Trigger Description Digital input signal used to select between the line binning operation and area scanning operation. HCMOS compatible. High level or left open: line binning operation Low level: area scanning operation Analog video output. Positive polarity Analog power supply Analog power supply Digital power supply Digital input signal for initializing the circuit. HCMOS compatible. Positive logic. The interval of the start pulses determines the integration time of the CCD image sensor. Digital input signal for operating the circuit. HCMOS compatible. Rising edge operation. Digital input signal for indicating end-of-scan of the image sensor. HCMOS compatible. Negative logic. Analog ground Analog ground Analog power supply Digital ground Digital ground Digital ground Digital output signal for A/D conversion. HCMOS compatible. Positive logic. I Pin assignment of "TE CONTROL I/O" connector (C7021, C7025) 9-pin D-sub connector 5 4 3 2 1 9 8 7 6 KACCC0075EA Description Digital power supply Analog output signal of the temperature of the CCD image sensor Digital input signal for starting to cool down. HCMOS compatible. 3 Cooling control High level or left open: cooling Low level: stand-by Power supply for the thermoelectric cooler in the CCD image sensor. 4 Vp (+5 V) (Please use AWG 18 wire) 5 VF (+12 V) Power supply for cooling fan 6 D. GND Ground 7 D. GND Ground Power supply return of the thermoelectric cooler mounted in the CCD image sensor. 8 P. GND (Please use AWG 18 wire) 9 F. GND Power supply return for cooling fan Available for using same power supply (+5 V) for "+VD2" and "+Vp". Caution: Do not connect "VD2" and "Vp" together on the backside of the 9-pin D-sub connector. These may be connected (shorted) at the power supply end, not 9-pin D-sub connector. Pin No. 1 2 Terminal name VD2 (+5 V) Temp monitor 5 CCD multichannel detector head I Dimensional outlines (unit: mm) C7020 1.3 0.5 C7020, C7021, C7025 34.0 FOCAL PLANE 100.0 62.0 11.0 80.0 90.0 60.0 50.0 FOCAL PLANE 50.0 (4 ×) M3 DEPTH 4 KACCA0058EA C7021 35.0 82.0 3.4 0.5 34.0 FOCAL PLANE 77.0 100.0 62.0 11.0 80.0 90.0 60.0 50.0 FOCAL PLANE 50.0 (4 ×) M3 DEPTH 4 KACCA0059EA C7025 35.0 2.5 0.5 34.0 FOCAL PLANE 77.0 100.0 62.0 11.0 80.0 90.0 60.0 50.0 FOCAL PLANE 50.0 (4 ×) M3 DEPTH 4 KACCA0060EA 6 82.0 82.0 CCD multichannel detector head I Connection example TE CONTROLLER POWER SUPPLY VF (+12V) F.GND VP (+5V) P.GND VD2 (+5V) D.GND CONTROLLER Cooling Control D.GND 9 8 3 7 6 2 1 5 4 C7020, C7021, C7025 I/O SIGNAL PULSE GENERATOR CLK D.GND Start D.GND VD1 (+5V) D.GND VA1+ (+15V) VA1- (-15V) VA2 (+24V) A.GND Mode Select D.GND Analog Input A.GND S/H Input D.GND CH1 GND Ext.Trig GND KACCC0076EB 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 POWER SUPPLY CONTROLLER S/H or A/D OSCILLOSCOPE Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. ©2003 Hamamatsu Photonics K.K. HAMAMATSU PHOTONICS K.K., Solid State Division 1126-1 Ichino-cho, Hamamatsu City, 435-8558 Japan, Telephone: (81) 053-434-3311, Fax: (81) 053-434-5184, http://www.hamamatsu.com U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P.O.Box 6910, Bridgewater, N.J. 08807-0910, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218 Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 08152-3750, Fax: (49) 08152-2658 France: Hamamatsu Photonics France S.A.R.L.: 8, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10 United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777 North Europe: Hamamatsu Photonics Norden AB: Smidesvägen 12, SE-171 41 Solna, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01 Italy: Hamamatsu Photonics Italia S.R.L.: Strada della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39) 02-935-81-733, Fax: (39) 02-935-81-741 Cat. No. KACC1035E06 Feb. 2003 DN 7