L7685

60 W XENON FLASH LAMP SERIES BUILT-IN REFLECTIVE MIRROR L7684, L7685/L6604, L6605 FEATURES High Stability: Fluctuation (p-p) 3 % Max. High Input Energy: 1 J (per one flash) Long Life: 8 × 107 flashes Min. Short Arc: 3 mm Spectral Distribution: 190 nm to 2000 nm (Sapphire glass window type) High Repetition Rate Meeting TV rate: 60 Hz Short flash pulse-width (FWHM): 2.90 µs (at 2 µF, 1000 V) Built-in Reflective Mirror/1.5 Times Brighter (L7684, L7685) TLSXF0105 APPLICATIONS Stroboscope for FA High Speed Image Processing Industrial Stroboscope Pollution Analysis TLSXF0103 CHARACTERISTICS Parameter Window Material Spectral Distribution Reflective Mirror Operating Voltage Recommended Operating Voltage Trigger Voltage Trigger Capacitor Value Maximum Average Input Energy (single) Maximum Average Input (continuous) Arc Length Maximum Repetition Rate Output Fluctuation (p-p) g d c b a L7684 L6604 L7685 L6605 Unit nm V V kV µF J W mm Hz % Max. flashes Min. Borosilicate Glass 240 to 2000 Built-in — Single Crystal Sapphire Glass 190 to 2000 Built-in — 300 to 1000 700 to 1000 5 to 10 0.22 1 60 3 60 3 8 × 107 E6647 C6096 E6611 e f Guaranteed Life (number of flashes) Applicable Trigger Socket Applicable Power Supply Applicable Cooling Jacket NOTE: a Average input energy (E) is calculated by the below formula. E = 1/2 CV2 E: Average input energy (J) C: Main discharge capacitor value (F) V: Main discharge voltage (V dc) b Average Input(W) is calculated by the below formula. W=E×f f: Repetition frequency (repetition rate) c At 1 J/flash (60 W) input. Maximum 100 Hz operation is possible with keeping average input 60 W or lower. d At 1 J/flash input energy (60 W) with using the cooling jacket of E6611. e It is necessary to have an additional external capacitor E7289-02 for 60 W input, when 1 J/flash input energy is needed. f It has to be used for the operation more than 15 W input. g Measured with supply voltage of 1000 V, main discharge capacitir of 2 µF and repetition rate of 10 Hz. Subject to local technical requirements and regulations, availability of products included in this promotional material may vary. Please consult with our sales office. Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. ©2006 Hamamatsu Photonics K.K 60 W XENON FLASH LAMP SERIES Figure 1: Spectral Distribution 2 1.8 1.6 TLSXB0104EA Figure 2: Flash Pulse Waveforms (L6604, L6605) TLSXB0084EA 100 60 W Xenon Flash Lamp Buit-in Reflective Mirror L7685 (1 J: 2 µF/1 kV) 60 W Xenon Flash Lamp L6605 (1 J: 2 µF/1 kV) 80 1 J/flash 1.4 1.2 1 0.8 0.6 0.4 0.2 0 200 300 400 500 600 700 800 RELATIVE INTENSITY (%) RELATIVE INTENSITY 60 FWHM 2.90 µs 0.15 J/flash FWHM 1.75 µs 40 20 0 WAVELENGTH (nm) TIME (2 µs/div.) Figure 3: Life Characteristics 100 TLSXB0083EC Figure 4: Dimensional Outline (Unit: mm) L7684, L7685 (Built-in Reflective Mirror) 34.8 ± 0.5 14.3 ± 0.15 OUTPUT WINDOW RELATIVE INTENSITY (%) 80 60 REFLECTIVE MIRROR 28.9 ± 0.3 3 PIN CONNECTION (BOTTOM VIEW) ANODE 1 40 20 GUARANTEED LIFE 0 2 × 107 (100) 4 × 107 (200) 6 × 107 (300) 8 × 107 (400) 1 × 108 (500) 25.8 ± 0.5 34.5 ± 0.5 2 TRIGGER PROBE 5 3 4 SPARKER TRIGGER PROBE CATHODE 15 MAX. 1.3 0 NUMBER OF FLASHES *( ) OPERATING TIME [h] MAIN DISCHARGE VOLTAGE: 1 kV MAIN DISCHARGE CAPACITOR: 2 µF REPETITION RATE: 60 Hz INPUT ENERGY: 1 J / FLASH The life end is defined as the time when the radiant intensity falls to 50 % of its initial value or when the output flutuation exceeds ±3 %. 28.9±0.3 3 PIN CONNECTION (BOTTOM VIEW) ANODE 1 2 TLSXA0082EA L6604, L6605 34.8±0.5 14.3±0.15 OUTPUT WINDOW TRIGGER PROBE 25.8±0.5 34.5±0.5 5 3 4 SPARKER TRIGGER PROBE CATHODE 15 MAX. 1.3 TLSXA0049EC RELATED PRODUCTS Trigger Socket E6647 In order to operate a Xenon flash lamp, it is necessary to supply the prescribed high voltage between anode and cathode, and to trigger probes. To facilitate the above operation, the trigger socket consists of high voltage transformer and voltage divider resistors and capacitors chain to supply the appropriate pulse voltage to each electrode. As E6647 radiates heat from its metal parts during the operation due to the input energy, it is recommended to use a cooling fan to keep the surface temperature of the metal parts at less than 50 °C. Dimensional Outline (Unit: mm) 14.8±0.1 METAL RED : MAIN DISCHAGE VOLTAGE WHITE : TRIGGER VOLTAGE BLACK : GND (MAIN) BROWN : GND (TRIGGER) 5.5 28.5±1.0 73.5±2.0 500±20 TLSXA0050EB * Changing the length of the trigger socket cable vavies the current flowing through the lamp so the lamp might fail to meet its required specifications. Use the cable length as shipped. Power Supply C6096 C6096 has large capability to operate the lamp stable in spite of its compact dimensions. When 1 flash input energy becomes over 0.05 J, it is necessary to have an additional external capacitor E7289-02 (option). Specifications Parameter Output Voltage h i (dc) Main Output Capacity Power Supply Stability Main Supply Capacitor j Trigger Trigger Output Voltage Section Trigger Capacitor Trigger Type Trigger Repetition Rate k Input Trigger Input Impedance Section Input Waveform m Input Voltage Input Voltage (dc) Power Consumption Cooling Weight Dimensional Outline (Unit: mm) 24.0±0.5 100.0±0.5 2-M3 80.0±0.5 14 TLSXA0051EA Description/Value 300 V to 1000 V 60 W Max. ±1 % Max. 0.1 µF 180 V Typ. 0.22 µF Internal / External 10 Hz to 100 Hz 360 Ω Rectangular Waveform 5V 24 V ± 1.2 V 90 W Not Required Approx. 550 g 108±2 174±3 2-M3 NOTE: The range of 700 V to 1000 V is used for the operation of 60 W Xenon flash lamp series. i In the case of connects temperature sensor lead lines from the cooling jacket, the output voltage becomes 0 V when the temperature sensor turns on. j When 1 flash input energy becomes over 0.05 J, it is necessary to have an additional external capacitor E7289-02 (option). k Don’t use beyond 60 Hz at the operation of 60 W input. m A trigger pulse voltage is supplied to each electrode at the same time as an input trigger signal rise. h 140.0±0.5 49±2 60 W XENON FLASH LAMP SERIES Cooling Jacket E6611 This cooling jacket is exclusively designed for 60 W Xenon flash lamps will keep the temperature of the lamp and electric parts such as the trigger socket at less than maximum ratings and maintain at even temperature by a built-in cooling fan, and offers the stable operation of the lamp. It has to be used for the operation of more than 15 W input. Dimensional Outline (Unit:mm) SETTING HOLES 2-M4 × P0.7 LAMP TRIGGER SOCKET 35.0 ± 0.5 65.5 ± 0.5 TEMPERATURE SENSOR* TRIGGER SOCKET SHIELD CABLE * The temperature sensor is for the protection of a lamp, a trigger socket and a power supply, when it detects an abnornal high temperature due to out of work with the cooling fan. When lead lines of temperature sensor are connected to the protection circuit terminal of C6096 exclusive power supply, the power supply will stop its operation. 62.0±0.5 M23 × P1 COOLING FAN (RATING : 24 V, 0.1 A dc) RED: Cooling fan input voltage (+24 V) BLACK: Cooling fan GND YELLOW: Temperature sensor 23.5±1.5 175±3 BLUE: Temperature sensor TLSXA0052ED Light-Guides Light-guides are effective to guide the output light into a place where does not allow to direct irradiation due to its construction or to plural places simultaneously. A short arc of 60 W Xenon flash lamps allows the light into the light-guides effectively. As the standard option, two types of light guide are available from us upon your application. Please refer to below table. The light-guides holder will be included for order of the cooling jacket E6611. Type No. A2873 A7432 Material Quartz glass fiber Transmittance wavelength Output diameter Length Dimensional Outline (Unit: mm) 1000 30 25 15 60 7 10 33 11 SUS FLEXIBLE TUBE 10 320 ± 20 100 ± 3 2-M3 78 ± 1 100 ± 1 50 60 ± 2 GND TERMINAL TLSXA0053ED 13 220 nm to 1300 nm 5 mm 5 mm 1m 1m TLSXA0062EB Compound glass fiber 380 nm to 1300 nm External Main Discharge Capacitor E7289-02 The exclusive main discharge capacitor (2 µ F) for 60 W (1 J/Flash, 60 Hz) inputs the operation of 60 W Xenon flash lamp series. It allows to operate safely by easy connection with a power supply. Dimensional Outline (Unit: mm) 180 ± 3 Warranty The warranty period will be one year following the date of shipment or specified life time whichever comes first. The area of warranty is Iimited to replacement of the faulty lamp. Faults resulting from natural disasters and improper usage will also be excluded from warranty. WEB SITE www.hamamatsu.com HAMAMATSU PHOTONICS K.K., Electron Tube Division 314-5, Shimokanzo, Iwata City, Shizuoka Pref., 438-0193, Japan, Telephone: (81)539/62-5248, Fax: (81)539/62-2205 U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P. O. Box 6910, Bridgewater. N.J. 08807-0910, U.S.A., Telephone: (1)908-231-0960, Fax: (1)908-231-1218 E-mail: usa@hamamatsu.com Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49)8152-375-0, Fax: (49)8152-2658 E-mail: info@hamamatsu.de France: Hamamatsu Photonics France S.A.R.L.: 8, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: (33)1 69 53 71 00, Fax: (33)1 69 53 71 10 E-mail: infos@hamamatsu.fr United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road Welwyn Garden City Hertfordshire AL7 1BW, United Kingdom, Telephone: 44-(0)1707-294888, Fax: 44(0)1707-325777 E-mail: info@hamamatsu.co.uk North Europe: Hamamatsu Photonics Norden AB: Smidesvägen 12, SE-171-41 SOLNA, Sweden, Telephone: (46)8-509-031-00, Fax: (46)8-509-031-01 E-mail: info@hamamatsu.se TLSX1029E04 Italy: Hamamatsu Photonics Italia: S.R.L.: Strada della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39)02-935 81 733, Fax: (39)02-935 81 741 E-mail: info@hamamatsu.it FEB. 2006 IP 6.5