R446

PHOTOMULTIPLIER TUBE R446 Multialkali Photocathode Sensitive to 870 nm 28 mm (1-1/8 Inch) Diameter, 9-Stage, Side-On Type The R446 features high quantum efficiency, high current amplification, good S/N ratio and wide spectral response from UV to near infrared. The R446 employs a UV-transmitting glass envelope for UV sensitivity extension. The R446 is well suited for use in broad-band spectrophotometers, atomic absorption spectrophotometers, chromatographs, NOx analyzers and other precision photometric instruments. FEATURES GWide Spectral Response ......................... 185 nm to 870 nm GCathode Sensitivity Luminous ......................................................... 120 µA/lm Radiant at 330 nm ............................................. 44 mA/W GAnode Sensitivity (at 1000 V) Luminous ........................................................... 600 A/lm Radiant at 330 nm ...................................... 2.2 × 105 A/W GLow Drift and Hysteresis Figure 1: Typical Spectral Response SPECIFICATIONS GENERAL Parameter Description/Value 185 to 870 Spectral Response 330 Wavelength of Maximum Response MateriaI Multialkali Photocathode Minimum Effective Area 8 × 24 UV glass Window Material Secondary Emitting Surface Multialkali Structure Circular-cage Dynode Number of Stages 9 4 Direct Interelectrode Anode to Last Dynode 6 Anode to All Other Electrodes Capacitances Base 11-pin base JEDEC No. B11-88 Weight Approx. 45 Operating Ambient Temperature -30 to +50 Storage Temperature -30 to +50 SuitabIe Socket E678–11A (Sold Separately) E717–63 (Sold Separately) SuitabIe Socket Assembly E717–74 (Sold Separately) Unit nm nm — mm — — — — pF pF — g °C °C — — CATHODE RADIANT SENSITIVITY (mA/W) QUANTUM EFFICIENCY (%) TPMSB0090EB 100 CATHODE RADIANT SENSITIVITY 10 1 QUANTUM EFFICIENCY 0.1 0.01 100 200 300 400 500 600 700 800 900 1000 WAVELENGTH (nm) Subject to local technical requirements and regulations, availability of products included in this promotional material may vary. Please consult with our sales office. Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are subject to change without notice. No patent rights are granted to any of the circuits described herein. ©2006 Hamamatsu Photonics K.K. PHOTOMULTIPLIER TUBES R446 MAXIMUM RATINGS (Absolute Maximum Values) Parameter Between Anode and Cathode Supply Voltage Between Anode and Last Dynode Average Anode Current A Value 1250 250 0.1 Unit V V mA CHARACTERISTlCS (at 25 °C) Parameter Quantum Efficiency (at Peak Wavelength) Luminous B at 194 nm at 254 nm Radiant at 330 nm at 633 nm at 852 nm Red/White Ratio C Blue Sensitivity Index D Luminous E at 194 nm at 254 nm Radiant at 330 nm at 633 nm at 852 nm Min. — 80 — — — — — 0.1 — 100 — — — — — — — — — — — — Typ. 16.7 (at 320 nm) 120 9.0 25 44 17 0.25 0.25 6.0 600 4.5 × 104 1.3 × 105 2.2 × 105 8.5 × 104 1.3 × 103 5.0 × 106 3 3.1 × 10-16 2.2 22 0.1 1.0 Max. — — — — — — — — — — — — — — — — 50 — — — — — Unit % µA/lm mA/W mA/W mA/W mA/W mA/W — — A/lm A/W A/W A/W A/W A/W — nA W ns ns % % Cathode Sensitivity Anode Sensitivity Gain E Anode Dark Current F (After 30 min Storage in Darkness) ENI (Equivalent Noise Input) H Anode Pulse Rise Time I Time Response E Electron Transit Time J Light Hysteresis Anode Current Stability K Voltage Hysteresis NOTES A: Averaged over any interval of 30 seconds maximum. B: The light source is a tungsten filament lamp operated at a distribution temperature of 2856K. Supply voltage is 100 V between the cathode and all other electrodes connected together as anode. C: Red/White ratio is the quotient of the cathode current measured using a red filter (Toshiba R-68) interposed between the light source and the tube by the cathode current measured with the filter removed under the same conditions as Note B. D: The value is cathode output current when a blue filter (Corning CS 5-58 polished to 1/2 stock thickness) is interposed between the light source and the tube under the same condition as Note B. E: Measured with the same light source as Note B and with the voltage distribution ratio shown in Table 1 below. Table 1:Voltage Distribution Ratio Electrode Distribution Ratio K 1 Dy1 Dy2 Dy3 Dy4 Dy5 Dy6 Dy7 Dy8 Dy9 1 1 1 1 1 1 1 1 1 P ENI = where 2q.ldb.G.∆f S q = Electronic charge (1.60 × 10-19 coulomb). ldb = Anode dark current(after 30 minute storage) in amperes. G = Gain. ∆f = Bandwidth of the system in hertz. 1 hertz is used. S = Anode radiant sensitivity in amperes per watt at the wavelength of peak response. I: The rise time is the time for the output pulse to rise from 10 % to 90 % of the peak amplitude when the entire photocathode is illuminated by a delta function light pulse. J: The electron transit time is the interval between the arrival of delta function light pulse at the entrance window of the tube and the time when the anode output reaches the peak amplitude. In measurement, the whole photocathode is illuminated. K: Hysteresis is temporary instability in anode current after light and voltage are applied. SuppIy Voltage: 1000 V, K: Cathode, Dy: Dynode, P: Anode ANODE CURRENT l max. l min. TIME 0 5 6 7 (minutes) F: Measured with the same supply voltage and voltage distribution ratio as Note E after removal of light. G:Measured at a supply voltage adjusted to provide an anode sensitivity of 100 A/lm. H: ENI is an indication of the photon-limited signal-to-noise ratio. It refers to the amount of light in watts to produce a signal-to-noise ratio of unity in the output of a photomultiplier tube. li TPMSB0002EA Hysteresis = lmax. li lmin. × 100 (%) (1)Light Hysteresis The tube is operated at 750 V with an anode current of 1 µA for 5 minutes. The light is then removed from the tube for a minute. The tube is then re-illuminated by the previous light level for a minute to measure the variation. ((2)Voltage Hysteresis The tube is operated at 300 V with an anode current of 0.1 µA for 5 minutes. The light is then removed from the tube and the supply voltage is quickly increased to 800 V. After a minute, the supply voltage is then reduced to the previous value and the tube is re-illuminated for a minute to measure the variation. Figure 2: Anode Luminous Sensitivity and Gain Characteristics 105 TPMSB0091EC Figure 3: Typical Time Response 108 100 80 60 TPMSB0092EC ANODE LUMINOUS SENSITIVITY (A/lm) 104 TYPICAL GAIN 107 40 TRANSIT TIME 103 106 20 102 TYPICAL ANODE SENSITIVITY 105 TIME (ns) GAIN 10 8 6 101 104 4 RISE TIME 100 MINIMUM ANODE SENSITIVITY 103 2 10-1 500 700 1000 102 1500 1 500 700 1000 1500 SUPPLY VOLTAGE (V) SUPPLY VOLTAGE (V) Figure 4: Typical Temperature Coefficient of Anode Sensitivity 160 TPMSB0093EC Figure 5: Typical Temperature Characteristic of Dark Current (at 1000 V, after 30 min strage in darkness) 100 TPMSB0094EB 140 800 nm 120 ANODE DARK CURRENT (nA) 10 ANODE SENSITIVITY (%) 600 nm 100 400 nm 80 1 60 40 0.1 20 0 -30 -20 -10 0 +10 +20 +30 +40 +50 0.01 -30 -20 -10 0 +10 +20 +30 +40 +50 TEMPERATURE (°C) TEMPERATURE (°C) PHOTOMULTIPLIER TUBES R446 Figure 6: Dimensional Outline and Basing Diagram (Unit: mm) 28.5 ± 1.5 8 MIN. PHOTOCATHODE DY5 24 MIN. DY4 4 80 MAX. DY3 3 94 MAX. DY2 2 1 11 K 4 Figure 7: Socket (Unit: mm) E678-11A 49 38 Sold Separately 5 7 8 DY8 5 9 DY9 10 P 29 49.0 ± 2.5 DY1 DIRECTION OF LIGHT 18 Bottom View (Basing Diagram) 32.2 ± 0.5 11 PIN BASE JEDEC No. B11-88 TPMSA0008EA TACCA0064EA Figure 8: D Type Socket Assembly (Unit: mm) Sold Separately E717-63 E717-74 HOUSING (INSULATOR) SOCKET PIN No. 10 P R10 DY9 9 R9 DY8 DY7 8 R8 7 R7 2 DY6 DY5 6 R6 5 R5 31.0 ± 0.5 HOUSING (INSULATOR) DY4 DY3 DY2 4 R4 3 R3 2 R2 DY1 K 1 R1 11 -HV AWG22 (VIOLET) R13 4- 2.8 * "Wiring diagram applies when -HV is supplied." To supply +HV,connect the pin "G" to+HV, and the pin "K" to the GND. R1 to R10 : 330 kΩ C1 to C3 : 10 nF 7 C1 C2 26.0±0.2 32.0±0.5 TOP VIEW 14.0±0.5 C3 SOCKET PIN No. 10 P R10 DY9 DY8 DY7 DY6 DY5 DY4 DY3 DY2 0.7 DY1 K 9 R9 8 R8 7 R7 6 R6 5 R5 4 R4 3 R3 2 R2 1 R1 11 -HV (K) R1 to R10 : 330 kΩ C1 to C3 : 10 nF C1 C2 C3 SIGNAL OUTPUT (A) GND (G) 5 33.0 ± 0.3 3.5 PMT SIGNAL GND SIGNAL OUTPUT RG-174/U(BLACK) POWER SUPPLY GND AWG22 (BLACK) PMT 32.0±0.5 26.0±0.2 38.0 ± 0.3 49.0 ± 0.3 29.0 ± 0.3 4 0.7 30.0 +0 -1 A G 2.7 22.4±0.2 SIDE VIEW K 450 ± 10 POTTING COMPOUND ° 10 30° BOTTOM VIEW TACCA0002EH TACCA0277EA * Hamamatsu also provides C4900 series compact high voltage power supplies and C6270 series DP type socket assemblies which incorporate a DC to DC converter type high voltage power supply. Warning–Personal Safety Hazards Electrical Shock–Operating voltages applied to this device present a shock hazard. WEB SITE www.hamamatsu.com HAMAMATSU PHOTONICS K.K., Electron Tube Division 314-5, Shimokanzo, Iwata City, Shizuoka Pref., 438-0193, Japan, Telephone: (81)539/62-5248, Fax: (81)539/62-2205 U.S.A.: Hamamatsu Corporation: 360 Foothill Road, P. O. Box 6910, Bridgewater. N.J. 08807-0910, U.S.A., Telephone: (1)908-231-0960, Fax: (1)908-231-1218 E-mail: usa@hamamatsu.com Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49)8152-375-0, Fax: (49)8152-2658 E-mail: info@hamamatsu.de France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: (33)1 69 53 71 00, Fax: (33)1 69 53 71 10 E-mail: infos@hamamatsu.fr United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road Welwyn Garden City Hertfordshire AL7 1BW, United Kingdom, Telephone: 44-(0)1707-294888, Fax: 44(0)1707-325777 E-mail: info@hamamatsu.co.uk North Europe: Hamamatsu Photonics Norden AB: Smidesvägen 12, SE-171-41 SOLNA, Sweden, Telephone: (46)8-509-031-00, Fax: (46)8-509-031-01 E-mail: info@hamamatsu.se Italy: Hamamatsu Photonics Italia: S.R.L.: Strada della Moia, 1/E, 20020 Arese, (Milano), Italy, Telephone: (39)02-935 81 733, Fax: (39)02-935 81 741 E-mail: info@hamamatsu.it TPMS1027E02 3.5 33 DY6 6 DY7 JUL. 2006. IP