8168SHCQE1

8060 Series Alternate Action and Momentary Pushbutton Switches Features/Benefits • Long travel • Available with LED • Long life contact design • Epoxy terminal seal Pushbutton A Typical Applications • Instrumentation • Computers and peripherals •  Telecommunications and networking equipment compatabile with bottom wash cleaning • RoHS compliant models available Models Available Specifications Materials CONTACT RATING: Q contact material: 6 AMPS @ 120 V AC or 28 V DC; 3 AMPS @ 250 V AC. See page A-59 for additional ratings. CASE: Glass filled nylon 6/6 or diallyl phthalate (DAP), flame retardant (UL 94V-0). PLUNGER: S, S1, S2 Options: Glass filled nylon or glass filled polyester (PBT) (UL 94V-0). L, L1 Options: Brass, nickel plated. ELECTRICAL LIFE: 50,000 make-and-break cycles at full load. CONTACT RESISTANCE: Below 20 mΩ typ. initial @ 2-4 V DC, 100 mA, for both silver and gold plated contacts. INSULATION RESISTANCE: 109Ω min. CAP & FRAME: Nylon, black standard. DIELECTRIC STRENGTH: 1,000 Vrms min. @ sea level. SWITCH SUPPORT: Brass or steel, matte-tin plated. BUSHING: Brass or zinc, nickel plated. HOUSING: Stainless steel. OPERATING TEMPERATURE: –30ºC to 65ºC END CONTACTS: Q contact material: Coin silver, silver plated. See page A-59 for additional contact materials. SOLDERABILITY: Per MIL-STD-202F method 208D, or EIA RS-186E method 9 (1 hour steam aging). CENTER CONTACT & ALL TERMINALS: Q contact material: Copper alloy, silver plated. See page A-59 for additional contact materials. CAP INSTALLATION FORCE: 10 lbs. maximum permissible. NOTE: Any models supplied with P, R, S, Q, B or G contact material are RoHS compliant. TERMINAL SEAL: Epoxy. Refer to soldering and cleaning in Technical Data Chapter. NOTE: Specifications and materials listed above are for switches with standard options. For information on specific and custom switches, consult Customer Service Center. HARDWARE: Nut & Locking Ring: Brass, nickel plated; Lockwasher: Steel, nickel plated. Build-A-Switch To order, simply select desired option from each category and place in the appropriate box. Available options are shown and described on pages A-53 thru A-61. For additional options not shown in catalog, consult Customer Service Center. All models have epoxy terminal seal and are compatible with all “bottom-wash” PCB cleaning methods. Switch Function 8161 SPDT On-On 8168 SPDT On-Mom. 8261 DPDT On-On Actuator or Plunger S .710” high plunger with .375” dia. cap J80 Snap-in J81 Snap-in with frame J82 Snap-in with frame for LED J86 Snap-in with frame & LED L .740” high plunger with .395” dia. cap L1 .740” high plunger with .590” dia. cap S1 .615” high plunger with .200” dia. cap S2 .710” high plunger with .310” dia. cap Bushing H .300” high, flat, hi torque H9 .300” high, flat, hi torque NONE No bushing choice required Y3 7.6mm, keyway Terminations A Right angle, PC thru-hole AV2 Vertical right angle, PC thru-hole C PC Thru-hole Z Solder lug A3 Right angle, snap-in, PC thru-hole AV3 Vertical right angle, snap-in, PC thru-hole V3 .460” high, V-bracket V4 .630” high, V-bracket V6 .460” high, V-bracket V21 .555” high, snap-in V-bracket V31 .460” high, snap-in V-bracket W .750” long, wire wrap Z3 Quick connect Contact Material B Gold P Gold, matte-tin Q Silver S Silver, matte-tin G Gold over silver R Gold over silver, matte-tin Seal E Epoxy I Epoxy potted base Cap Color 2 Black 1 White 3 Red 4 Orange 5 Yellow 9 Gray Frame Color 2 Black LED Color 3 Red NONE Models without LED Dimensions are shown: Inches (mm) Specifications and dimensions subject to change 29 Aug 18 A-52 www.ckswitches.com 8060 Series Alternate Action and Momentary Pushbutton Switches SWITCH FUNCTION POS. 1 NO. POLES SP POS. 2 C&K marking this side MODEL NO. A CONNECTED TERMINALS POS. 1 Pushbutton SWITCH FUNCTION POS. 2 C&K marking this side 8161 ON ON 2-3 2-1 8168 ON MOM. 2-3 2-1 SCHEMATIC SPDT SPDT Terminal Nos. For Reference Only Part number shown: 8161SHZQE DP 8261 ON ON 2-3,5-6 2-1,5-4 DPDT DPDT Terminal Nos. For Reference Only Part number shown: 8261SHZQE MOM. = Momentary All models with all options when ordered with G or Q contact material. CAP COLOR ACTUATOR—SNAP-IN FRONT MOUNT ACTUATOR OR PLUNGER J80  SNAP-IN OPTION CODE PANEL MOUNTING * CAP COLOR 2 BLACK 1 WHITE 3 RED 4 ORANGE 5 YELLOW 9 GRAY *Increase this dimension to .620/.625 (15,75/15,88) for .091/.125 (2,41/2,18) thick panels. J81  SNAP-IN WITH BLACK FRAME Cap Finish: matte. Other colors available, consult Customer Service Center. PANEL MOUNTING Available with C, W, Z or Z3 terminations. NOTE: Caps & frames available separately, see pages A-60 and A-61. * *Increase this dimension to .620/.625 (15,75/15,88) for .091/.125 (2,41/2,18) thick panels. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change 29 Aug 18 A-53 www.ckswitches.com 8060 Series Alternate Action and Momentary Pushbutton Switches CAP COLOR Pushbutton A ACTUATOR—SNAP-IN FRONT MOUNT ACTUATOR OR PLUNGER J82  SNAP-IN WITH BLACK FRAME FOR LED Available with C, W, Z or Z3 terminations. LED not included. For LED information, see page A-61. OPTION CODE NOTE: Caps & frames available separately, see pages A-60 and A-61. Other colors available, consult Customer Service Center. CAP COLOR 2 BLACK 1 WHITE RED 3 4 ORANGE 5 YELLOW 9 GRAY CAP COLOR ACTUATOR—SNAP-IN FRONT MOUNT LED COLOR ACTUATOR OR PLUNGER J86  SNAP-IN WITH BLACK FRAME AND LED PANEL MOUNTING * 8161J86ZQE223 SPDT * Increase this dimension to .620/.625 (15,75/15,88) for .091/.125 (2,31/3,18) thick panels. Available with C, W, Z or Z3 terminations and SPDT models only. NOTE: Caps & frames available separately, see pages A-60 and A-61. Other colors available, consult Customer Service Center. OPTION CODE OPTION CODE CAP COLOR 2 BLACK 1 WHITE 3 RED 4 ORANGE 5 YELLOW 9 GRAY 3 LED COLOR RED For LED information, see page A-61. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change 29 Aug 18 A-54 www.ckswitches.com 8060 Series Alternate Action and Momentary Pushbutton Switches CAP COLOR PLUNGER A ACTUATOR OR PLUNGER S1  PLUNGER WITH CAP P/N 7089 L  PLUNGER WITH CAP P/N 8941 L1  PLUNGER WITH CAP P/N 8940 S2  PLUNGER WITH CAP P/N 8018 Pushbutton S  PLUNGER WITH CAP P/N 7527 OPTION CODE CAP COLOR 2 BLACK 1 WHITE 3 RED 4 ORANGE 5 YELLOW 9 GRAY Cap Finish: gloss. Cap supplied not installed. Other colors available, consult Customer Service Center. NOTE: When selecting plunger and cap option, bushing selection must also be made, see below. BUSHING H  .300” HIGH THREADED, FLAT H9  .300” HIGH UNTHREADED, FLAT NONE   NO BUSHING CHOICE REQUIRED Y3  7.6mm THREADED, KEYWAY (JXX ACTUATORS) 1/4±40 UNS-2A H bushing standard with C, W, Z or Z3 terminations. H9 bushing standard with A, A3, AV2, AV3, or V3-V31 terminations. Withstands 12 in./lbs. of torque with no distortion. Withstands 12 in./lbs. of torque with no distortion. NOTE: When selecting bushing option, plunger selection must also be made, see above. No bushing option choice required when any JXX actuator option is selected. NOTE. Two mounting nuts, locking ring and lockwasher supplied standard with threaded bushings. Optional mounting nut and locking ring styles and finishes available, see section “Technical Data and Additional Hardware”. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change 29 Aug 18 A-55 www.ckswitches.com 8060 Series Alternate Action and Momentary Pushbutton Switches Pushbutton A TERMINATIONS C  PC THRU-HOLE Z  SOLDER LUG PC MOUNTING SPDT and DPDT SPDT and DPDT Z3  QUICK CONNECT W  WIRE WRAP Not available with P, S or R contact material. .750 (19,05) Not available with P, S or R contact material. Mating quick connector available; order part number 530100000, page A-61. SPDT and DPDT SPDT and DPDT A  RIGHT ANGLE, PC THRUHOLE .130 (3,3) .138 (3,51) SECTION A-A 8161SH9ABE2 SPDT A3  RIGHT ANGLE, SNAP-IN, PC THRU-HOLE PC MOUNTING Not available with I seal. Terminal bend radii and lead-in manufacturing option. NOTE: PC pattern must clear switch support leg. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change 29 Aug 18 A-56 www.ckswitches.com 8060 Series Alternate Action and Momentary Pushbutton Switches TERMINATIONS A Pushbutton A  RIGHT ANGLE, PC THRU-HOLE 8261SH9ABE2 DPDT SECTION A-A A3  RIGHT ANGLE, SNAP-IN, PC THRU-HOLE PC MOUNTING Not available with I seal. Terminal bend radii and lead-in manufacturing option. AV2  VERTICAL RIGHT ANGLE, PC THRU-HOLE, .150” PITCH 8161SH9AV2BE2 SPDT AV3   VERTICAL RIGHT ANGLE, SNAP-IN, PC THRU-HOLE, .150” PITCH PC MOUNTING Not available with I seal. Terminal bend radii and lead-in manufacturing option. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change 29 Aug 18 A-57 www.ckswitches.com 8060 Series Alternate Action and Momentary Pushbutton Switches Pushbutton A TERMINATIONS AV2   VERTICAL RIGHT ANGLE, PC THRU-HOLE, .150” PITCH 8261SH9AV2BE2 DPDT SECTION A-A AV3   VERTICAL RIGHT ANGLE, SNAP-IN, PC THRU-HOLE, PC MOUNTING .150” PITCH Not available with I seal. Terminal bend radii and lead-in manufacturing option. V6  VERTICAL MOUNT, V-BRACKET V21  VERTICAL MOUNT, V-BRACKET, SNAP-IN PC MOUNTING OPTION CODE 8161SH9__BE2 SPDT V21 V6 DIM ‘A’ .555 (14,10) .460 (11,68) Not available with I seal. V6  VERTICAL MOUNT, V-BRACKET V21  VERTICAL MOUNT, V-BRACKET, SNAP-IN PC MOUNTING OPTION CODE V21 V6 8261SH9__BE2 DPDT DIM ‘A’ .555 (14,10) .460 (11,68) Not available with I seal. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change 29 Aug 18 A-58 www.ckswitches.com 8060 Series Alternate Action and Momentary Pushbutton Switches TERMINATIONS A Pushbutton V3, V4  VERTICAL MOUNT, V-BRACKET V31  VERTICAL MOUNT, V-BRACKET, SNAP-IN PC MOUNTING 8161SH9__BE2 SPDT OPTION CODE Not available with I seal. DIM ‘A’ V3, V31 .460 (11,68) V4 .630 (16,00) V3, V4  VERTICAL MOUNT, V-BRACKET V31  VERTICAL MOUNT, V-BRACKET, SNAP-IN PC MOUNTING 8261SH9__BE2 DPDT SNAP-IN OPTION CODE V3, V31 V4 Not available with I seal. DIM ‘A’ .460 (11,68) .630 (16,00) CONTACT MATERIAL OPTION CODE CONTACT MATERIAL B GOLD 1 P Q S SILVER 4,5 G GOLD OVER R SILVER 2,3 TERMINAL PLATING GOLD 1 MATTE-TIN 6 SILVER 5 MATTE-TIN 6 RATINGS LOW LEVEL/DRY CIRCUIT 0.4 VA MAX. @ 20 V AC OR DC MAX. POWER 6 AMPS @ 120 V AC OR 28 V DC; 3 AMPS @ 250 V AC. 0.4 VA MAX @ 20 V AC OR DC MAX. OR GOLD 3 MATTE-TIN 6 LOW LEVEL/DRY CIRCUIT OR POWER 6 AMPS @ 120 V AC OR 28 V DC; 3 AMPS @ 250 V AC. * Note: See Technical Data section of this catalog for RoHS compliant and compatible definitions and specifications. 1 CONTACTS & TERMINALS: Copper alloy, with gold plate over nickel plate. 2 END CONTACTS: Coin silver, with gold plate over nickel plate. 3 CENTER CONTACTS & ALL TERMINALS: Copper alloy, with gold plate over nickel plate. All models contact material. with all options when ordered with S, R, G, or Q B contact material standard with all terminations except C, Z & Z3. Q contact material standard with C, Z & Z3 terminations. 4 END CONTACTS: Coin silver, silver plated. P, S & R contact materials not available with Z & Z3 terminations. 5 CENTER CONTACT & ALL TERMINALS: Copper alloy, silver plated. 6 TERMINALS: Copper alloy, with matte-tin over nickel plate. NOTE: Any models supplied with P, S, R,Q, B or G contact material are RoHS compliant. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change 29 Aug 18 A-59 www.ckswitches.com 8060 Series Alternate Action and Momentary Pushbutton Switches Pushbutton A SEAL E  EPOXY SEAL I  EPOXY POTTED BASE NOTE: Available with C, W, Z, Z3 terminations only. AVAILABLE HARDWARE Cap Cap .120 (3,05) Cap .200 DIA. (5,08 ) .155 (3,94) PART NO. 708901000 708902000 708903000 708904000 708905000 708909000 PART NO. WHITE BLACK RED ORANGE YELLOW GRAY Material: Nylon Finish: Gloss PART NO. WHITE BLACK RED ORANGE YELLOW GRAY Material: Nylon Finish: Gloss Cap, Snap-fitting plunger PART NO. 452D01000 452D02000 452D03000 452D04000 452D05000 452D09000 752701000 752702000 752703000 752704000 752705000 752709000 Cap, Snap-fitting plunger Material: Nylon Finish: Gloss 894101000 894102000 894103000 894104000 894105000 894109000 Cap, J80, J81 & J82 options only PART NO. WHITE BLACK RED ORANGE YELLOW GRAY Material: Nylon Finish: Gloss Cap, J86 & J96 options only WHITE BLACK RED ORANGE YELLOW GRAY Material: Nylon Finish: Gloss PART NO. WHITE BLACK RED ORANGE YELLOW GRAY 801801000 801802000 801803000 801804000 801805000 801809000 484601000 484602000 484603000 484604000 484605000 484609000 PART NO. WHITE BLACK RED ORANGE YELLOW GRAY Material: Nylon Finish: Gloss 798201000 798202263 798203000 798204000 798205000 798209000 WHITE BLACK RED ORANGE YELLOW GRAY Material: Nylon Finish: Matte Frame Frame PART NO. 459701000 459702000 459703000 459704000 459705000 459709000 Material: Nylon Finish: Matte PART NO. PART NO. 615602263 BLACK 613302263 BLACK Material: Nylon Finish: Matte Material: Nylon Finish: Matte NOTE: Additional nuts, locking rings and lockwashers available separately, see section “Technical Data and Additional Hardware”. Other cap & frame colors available, consult Customer Service Center. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change 29 Aug 18 A-60 www.ckswitches.com 8060 Series Alternate Action and Momentary Pushbutton Switches AVAILABLE HARDWARE A Pushbutton Fits Z3 Termination female connector PART NO. 530100000 Available in loose pieces. Frames snap into panel opening and are independent from switch mounting. Accurate positioning of the PC mounted switch relative to the panel opening is necessary to provide proper clearance between actuator and frame. Available in two basic styles and four panel thicknesses .047-.125 in. Material: Nylon. Finish: Matte. Panel Inserts .090” (2,29) PANEL THK. .125” (3,18) PANEL THK. PART NO. PART NO. 432702263 432802263 BLACK TYPICAL APPLICATION Above frames (part nos. 432XXXXXX) are also available with insert which accepts LED for indicator light assembly. Order insert separately from frame. Blank insert panel (without hole for LED) also available. LED not included. PANEL INSERT WITH HOLE FOR LED BLANK PANEL INSERT WITHOUT HOLE FOR LED PART NO. PART NO. 894902000 476602000 BLACK Special colors, custom markings available, consult Customer Service Center. LED INFORMATION SWITCHES WITH LED SUPPLIED: J86 OPTION: Rectangular LEDs are supplied on 8060 Series pushbutton switches with J86 option. These LEDs are factory installed and are not replaceable. The following specifications apply: OPTION CODE COLOR TYP. INTENSITY 6 Green 1.0 mcd 3 Red* 0.5 mcd 5 Yellow 4.0 mcd TYP. FORWARD VOLTAGE MAX RATINGS AT 25ºC AMBIENT TEMPERATURE TYP. CONTINUOUS POWER FORWARD FORWARD FORWARD CURRENT DISSIPATION CURRENT VOLTAGE 20 mA 2.1 V 10 mA 20 mA 2.5 V 50 mA 125 mW 30 mA 75 mW 50 mA 125 mW Flat denotes cathode. .230 DIA. (5,84˘) Process Information: Soldering to LED leads must be completed within 5 seconds at 500ºF (260ºC) maximum. Caution: Circuit elements must limit forward current of LED to 50mA max. continuous. * Extra-bright red LED available (typ. intensity 4.5 mcd), consult Customer Service Center. LEDs are not supplied with J82 & J84 options. LED snaps into switch frame surrounding actuator and is wired externally. .200 DIA. (5,08˘) .025 SQ. TYP. (0,63) .030 (0,76) .750 (19,05) .340 (8,64) Suggested LED for J82 & J84 options. Dimensions for reference only. Third Angle Projection Dimensions are shown: Inches (mm) Specifications and dimensions subject to change 29 Aug 18 A-61 www.ckswitches.com