A1220UA4LRP

SIDACtor ® Protection Thyristors LCAS Protection Asymmetrical Multiport Series - MS-013 Pb e3 RoHS Description Asymmetrical Multiport Series are SIDACtor® components designed to protect LCAS (Line Circuit Access Switch) devices from damaging overvoltage transients. The series provides a specialized asymmetrical dual port overvoltage protection solution that enables equipment to comply with various global requlatory standards. Features and Benefits • Low voltage overshoot • Two-port protection • Low on-state voltage • RoHS Compliant, LeadFree and Halogen Free • Does not degrade surge capability after multiple surge events within limit. Agency Approvals Agency Agency File Number • LCAS specific tip and ring thresholds • Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin (Sn) (IPC/JEDEC J-STD609A.01) • Fails short circuit when surged in excess of ratings E133083 • Replaces four discrete components Pinout Designation Applicable Global Standards 1 6 • TIA-968-A • GR 1089 Intra-building 2 5 • TIA-968-B 3 4 • ITU K.20/21 Enhanced Level* • IEC 61000-4-5 2nd edition Schematic Symbol (T1) 1 6 (T2) (G1) 2 5 (G2) (R1) 3 4 (R2) • YD/T 1082 • ITU K.20/21 Basic Level • YD/T 993 • GR 1089 Inter-building* • YD/T 950 *A-rated parts require series resistance Additional Information Datasheet Samples Resources Electrical Characteristics Part Number Part Marking VS VDRM @IDRM VDRM @IDRM = 5µA @100V/µs = 5µA V V Pins 2-3, 5-6 A1220UA4Lxx A1225UA4Lxx A1220UC4Lxx A1225UC4Lxx A1220UA4 A1250UA4 A1220UC4 A1250UC4 100 100 100 100 130 130 130 130 V VS @100V/µs V Pins 1-2, 4-5 180 230 180 230 220 290 220 290 VT@IT = 2.2 Amps V IS mA IT A IH mA 800 800 800 800 2.2 2.2 2.2 2.2 120 120 120 120 Pins 1-2, 2-3, 4-5, 5-6 4 4 4 4 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Components are bi-directional. - All electrical characteristics shown are defined from Tip to Ground (pin 1 to pin 2 and pin 6 to pin 5) and Ring to Ground (pin 3 to pin 2 and pin 4 to pin 5). - XX = Part Number Suffix: ‘TP’ (Tube Pack) or ‘RP’ (Reel Pack). © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17 SIDACtor ® Protection Thyristors LCAS Protection Capacitance Values pF Pin 1-2 / 4-5 Ring-Ground Part Number A1220UA4Lxx A1225UA4Lxx A1220UC4Lxx A1225UC4Lxx pF Pin 3-2 / 6-5 Tip-Ground pF Pin 1-3 (4-6) Tip-Ring MIN MAX MIN MAX MIN MAX 15 15 35 35 25 25 50 50 30 30 60 60 50 50 90 90 5 5 20 20 20 20 35 35 Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. Surge Ratings Series IPP ITSM 50/60 Hz di/dt A min A min A/µs max 0.2/310 0.5/700 2 2/10 2/10 2 8/20 1.2/50 2 10/160 10/160 2 10/560 1 10/560 2 5/320 1 9/720 2 10/360 1 10/360 2 10/1000 1 10/1000 2 5/310 1 10/700 2 A min A min A min A min A min A min A min A min 1 1 1 1 A 20 150 150 90 50 75 75 45 75 20 500 C 50 500 400 200 150 200 175 100 200 30 500 Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The component must initially be in thermal equilibrium with -40°C < TJ < +150°C 1 Current waveform in µs 2 Voltage waveform in µs Thermal Considerations Package Symbol Modified MS-013 6 5 4 1 2 Value Unit TJ Operating Junction Temperature Range -40 to +125 °C TS Storage Temperature Range -65 to +150 °C 60 °C/W R0JA 3 Parameter Thermal Resistance: Junction to Ambient V-I Characteristics tr x td Pulse Waveform IT IS IH -V IDRM +V VT VDRM VS IPP – Peak Pulse Current – %IPP +I Peak Value 100 Waveform = tr x td 50 Half Value 0 0 -I © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17 tr = rise time to peak value td = decay time to half value tr td t – Time (µs) SIDACtor ® Protection Thyristors LCAS Protection Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature 2.0 10 IH 8 6 25 °C 4 IH (TC = 25ºC) 12 2 0 -4 1.8 1.6 1.4 0.8 0.6 -6 0.4 -40 -8 -40 -20 0 25°C 1.2 1.0 Ratio of Percent of VS Change – % 14 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC 20 40 60 80 100 120 140 160 Junction Temperature (TJ) – °C Soldering Parameters Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)°C Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C Physical Specifications Figure 1 TP TL TS(max) Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) recognized epoxy meeting flammability Asym Multiport Series MS-013UL Part Numbering.eps Body Material classification V-0 For pg. 146 Part Numbering A xxxx U x 4 L xx TYPE A: Asymmetrical SIDACtor MEDIAN VOLTAGE PACKAGE TYPE IPP RATING PACKING OPTIONS RP: Reel Pack TP: Tube Pack RoHS COMPLIANT CONSTRUCTION VARIABLE Time Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/ JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/JEDEC, JESD22-A-101 High Temp Storage +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/JEDEC, JESD22-A-102 Resistance to Solder Heat +260°C, 30 secs. MIL-STD-750 (Method 2031) Moisture Sensitivity Level 85%RH, +85°C, 168 hrs., 3 reflow cycles (+260°C Peak). JEDEC-J-STD-020, Level 1 100% Matte-Tin Plated Terminal Finish Critical Zone TL to TP tL Copper Alloy Lead Material tP Ramp-up Temperature Reflow Condition © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17 SIDACtor ® Protection Thyristors LCAS Protection MS-013 Part Marking Drawing_2009-03-05.eps Part Marking Packing Options Package Type Part Marking Code XXXXXXXX (Refer to Electrical Characteristics Table) Date Code XXXXX U Description Quantity Added Suffix Industry Standard Modified MS-013 6-pin Tape and Reel Pack 1500 RP EIA-481-D TP N/A 500 Modified MS-013 6-pin (50 per Tube Pack tube) Dimensions — MS-013 Dimensions 0.065 (1.65) Pad Outline C 0.460 (11.68) 0.138 (3.50) D 7º TYP J 7º TYP A Dimension are in inches (and millimeters). 0.059 (1.50) E G Burr Side H 96º A Mold Split Line 4º A 7º TYP BSC* F MIN Length of Flat 7º TYP Detail A K B A B C D E F G H J K BSC* Inches Millimeters Min Max Min Max 0.360 0.352 0.400 0.043 0.047 0.293 0.289 0.089 0.041 0.020 0.133 0.364 0.356 0.412 0.045 0.055 0.297 0.293 0.093 0.049 9.14 8.94 10.16 1.09 1.19 7.44 7.34 2.26 1.04 0.51 3.38 9.25 9.04 10.46 1.13 1.40 7.54 7.44 2.36 1.24 0.143 3.63 * BSC = Basic Spacing between Centers Tape and Reel Specification — MS-013 .157 (4.0) .630 (16.0) .472 (12.0) 12.99 (330) .512 (13.0) Arbor Hole Dia. Dimensions are in inches (and millimeters) 0.700 (17.8) Direction of Feed Tube Pack Specification — MS-013 Message Location .045 (1.14) .310 (7.87) 90˚ .165 (4.19) 6 Interior of the Tube .150 (3.81) .225 (5.72) .525 (13.34) .020 ± .005 WALL TYP. (0.51 ± 0.13) .108 (2.74) .005 A 20.000 ± .030 (508.00 ± 0.76) .110 (2.79) A Dimensions are in inches (and millimeters) Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 02/23/17