P6SMB75CA

TVS Diodes Surface Mount – 600W > P6SMB series P6SMB Series RoHS Pb e3 Description The P6SMB series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Uni-directional Features Bi-directional Agency Approvals Agency Agency File Number E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit by 10/1000us Peak Pulse Power Dissipation Test Waveform(Fig.4) (Note 1),(Note 2) -Single Die Parts PPPM 600 W Peak Pulse Power Dissipation by 10/1000us Test Waveform(Fig.4) (Note.1, Note.2)-Stacked Die Parts PPPM 800 W PD 5.0 W IFSM 100 A VF 3.5/5.0 V TJ -65 to 150 °C TSTG -65 to 175 °C (Fig.2) (Fig.2) (Note.5) Power Dissipation on Infinite Heat Sink at TL=50OC Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) Maximum Instantaneous Forward Voltage at 50A for Unidirectional Only (Note 4) Operating Temperature Range Storage Temperature Range Typical Thermal Resistance Junction to Lead RƟJL 20 °C/W Typical Thermal Resistance Junction to Ambient RƟJA 100 °C/W Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TJ (initial) =25OC per Fig. 3. 2. Mounted on copper pad area of 0.2x0.2” (5.0 x 5.0mm) to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only, duty cycle=4 per minute maximum. 4. VF < 3.5V for single die parts and VF< 5.0V for stacked-die parts. 5. For stacked die component details, please refer to part numbers labeled by * in Electrical Characteristics. • 600W peak pulse power capability at 10/1000μs waveform, repetition rate (duty cycles):0.01% • Excellent clamping capability • Low incremental surge resistance • Typical IR less than 1μA when VBR min>12V • Optimized surface mount footprint for minimal PCB space impact • Low profile package • Typical failure mode due to exceeding maximum ratings is a short circuit condition • Whisker test conducted based on Table 4a and 4c of JEDEC JESD201A • IEC 61000-4-2 ESD 30kV(Air), 30kV (Contact) • EFT protection of data lines in accordance with IEC 61000-4-4 • Built-in strain relief • Fast response time: typically less than 1.0ps from 0V to VBR min • High temperature to reflow soldering guaranteed: 260°C/30sec • VBR @ TJ= VBR@25°C x (1+αT x (TJ - 25)) (αT:Temperature Coefficient, typical value is 0.1%) • UL Recognized compound meeting flammability classification V-0 • Meet MSL level1, per J-STD-020, LF maximun peak of 260°C • Matte tin lead–free plated • Halogen free and RoHS compliant • Pb-free E3 means 2ND level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/ JEDEC J-STD-609A.01) • UL Recognized to ANSI/UL 497B: Protectors for Data Communications and FireAlarm Circuits. Applications TVS devices are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications. Functional Diagram Additional Infomarion Bi-directional Cathode Datasheet Resources Samples Anode Uni-directional © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BA.06/28/21 TVS Diodes Surface Mount – 600W > P6SMB series Electrical Characteristics (T =25°C unless otherwise noted) A Part Number (Uni) Part Number (Bi) P6SMB6.8A P6SMB7.5A P6SMB8.2A P6SMB9.1A P6SMB10A P6SMB11A P6SMB12A P6SMB13A P6SMB15A P6SMB16A P6SMB18A P6SMB20A P6SMB22A P6SMB24A P6SMB27A P6SMB30A P6SMB33A P6SMB36A P6SMB39A P6SMB43A P6SMB47A P6SMB51A P6SMB56A P6SMB58A P6SMB62A P6SMB68A P6SMB75A P6SMB82A P6SMB91A P6SMB100A P6SMB110A P6SMB120A P6SMB130A P6SMB150A P6SMB160A P6SMB170A P6SMB180A P6SMB200A P6SMB220A P6SMB250A P6SMB300A P6SMB350A* P6SMB400A* P6SMB440A* P6SMB480A* P6SMB510A* P6SMB530A* P6SMB540A* P6SMB550A* P6SMB600A* P6SMB6.8CA P6SMB7.5CA P6SMB8.2CA P6SMB9.1CA P6SMB10CA P6SMB11CA P6SMB12CA P6SMB13CA P6SMB15CA P6SMB16CA P6SMB18CA P6SMB20CA P6SMB22CA P6SMB24CA P6SMB27CA P6SMB30CA P6SMB33CA P6SMB36CA P6SMB39CA P6SMB43CA P6SMB47CA P6SMB51CA P6SMB56CA P6SMB58CA P6SMB62CA P6SMB68CA P6SMB75CA P6SMB82CA P6SMB91CA P6SMB100CA P6SMB110CA P6SMB120CA P6SMB130CA P6SMB150CA P6SMB160CA P6SMB170CA P6SMB180CA P6SMB200CA P6SMB220CA P6SMB250CA P6SMB300CA P6SMB350CA* P6SMB400CA* P6SMB440CA* P6SMB480CA* P6SMB510CA* P6SMB530CA* P6SMB540CA* P6SMB550CA* P6SMB600CA* Marking UNI BI 6V8A 7V5A 8V2A 9V1A 10A 11A 12A 13A 15A 16A 18A 20A 22A 24A 27A 30A 33A 36A 39A 43A 47A 51A 56A 58A 62A 68A 75A 82A 91A 100A 110A 120A 130A 150A 160A 170A 180A 200A 220A 250A 300A 350A 400A 440A 480A 510A 530A 540A 550A 600A 6V8C 7V5C 8V2C 9V1C 10C 11C 12C 13C 15C 16C 18C 20C 22C 24C 27C 30C 33C 36C 39C 43C 47C 51C 56C 58C 62C 68C 75C 82C 91C 100C 110C 120C 130C 150C 160C 170C 180C 200C 220C 250C 300C 350C 400C 440C 480C 510C 530C 540C 550C 600C Reverse Stand off Voltage VR (Volts) 5.80 6.40 7.02 7.78 8.55 9.40 10.20 11.10 12.80 13.60 15.30 17.10 18.80 20.50 23.10 25.60 28.20 30.80 33.30 36.80 40.20 43.60 47.80 52.78 53.00 58.10 64.10 70.10 77.80 85.50 94.00 102.00 111.00 128.00 136.00 145.00 154.00 171.00 185.00 214.00 256.00 300.00 342.00 376.00 408.00 434.00 451.00 460.00 468.00 512.00 Breakdown Voltage VBR (Volts) @ IT MIN MAX 6.45 7.13 7.79 8.65 9.50 10.50 11.40 12.40 14.30 15.20 17.10 19.00 20.90 22.80 25.70 28.50 31.40 34.20 37.10 40.90 44.70 48.50 53.20 55.10 58.90 64.60 71.30 77.90 86.50 95.00 105.00 114.00 124.00 143.00 152.00 162.00 171.00 190.00 209.00 237.00 285.00 332.00 380.00 418.00 456.00 485.00 503.50 513.00 522.50 570.00 7.14 7.88 8.61 9.55 10.50 11.60 12.60 13.70 15.80 16.80 18.90 21.00 23.10 25.20 28.40 31.50 34.70 37.80 41.00 45.20 49.40 53.60 58.80 60.90 65.10 71.40 78.80 86.10 95.50 105.00 116.00 126.00 137.00 158.00 168.00 179.00 189.00 210.00 231.00 263.00 315.00 368.00 420.00 462.00 504.00 535.00 556.50 567.00 577.50 630.00 Test Current IT (mA) Maximum Clamping Voltage VC @ Ipp (V) Maximum Peak Pulse Current Ipp (A) 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 10.5 11.3 12.1 13.4 14.5 15.6 16.7 18.2 21.2 22.5 25.5 27.7 30.6 33.2 37.5 41.4 45.7 49.9 53.9 59.3 64.8 70.1 77.0 79.8 85.0 92.0 103.0 113.0 125.0 137.0 152.0 165.0 179.0 207.0 219.0 234.0 246.0 274.0 328.0 344.0 414.0 482.0 548.0 602.0 658.0 698.0 725.0 740.0 760.0 828.0 58.1 54.0 50.4 45.5 42.1 39.1 36.5 33.5 28.8 27.1 24.2 22.0 19.9 18.4 16.3 14.7 13.3 12.2 11.3 10.3 9.4 8.7 7.9 7.7 7.2 6.6 5.9 5.4 4.9 4.5 4.0 3.7 3.4 2.9 2.8 2.6 2.5 2.2 1.9 1.8 1.5 1.7 1.5 1.4 1.3 1.2 1.2 1.1 1.1 1.0 Maximum Maximum Agency Reverse Temperature Approval Leakage IR coefficient @ VR of VBR (µA) (%/C) 1000 500 200 50 10 5 5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0.041 0.054 0.058 0.063 0.066 0.069 0.071 0.074 0.076 0.080 0.083 0.085 0.088 0.091 0.092 0.093 0.094 0.096 0.097 0.098 0.099 0.100 0.101 0.101 0.102 0.103 0.104 0.105 0.106 0.106 0.107 0.107 0.107 0.108 0.108 0.108 0.108 0.108 0.110 0.110 0.110 0.112 0.112 0.112 0.112 0.112 0.112 0.112 0.112 0.112 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X - For bidirectional type having VR of 10 volts and less, the IR limit is double. For stack-die parts, use * to label the part number. © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BA.06/28/21 TVS Diodes Surface Mount – 600W > P6SMB series I-V Curve Characteristics Bi-directional Uni-directional Ipp Vc VBR VR V IR VF IT IT IR Vc VBR VR IR IT V Ipp Ipp PPPM VR VBR VC IR VF VR VBR Vc Peak Pulse Power Dissipation -- Max power dissipation (VC * IPP) Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T =25°C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating Voltage Transients PPPM-Peak Pulse Power (kW) 100 Voltage or Current Voltage Across TVS Current Through TVS Time TJ initial = TAMB stacked-die, 800W at 10/1000µs, 25°C 10 1 0.1 0.001 Single die,600W at 10/1000µs, 25°C 0.01 0.1 1 10 td-Pulse Width (ms) © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BA.06/28/21 TVS Diodes Surface Mount – 600W > P6SMB series Ratings and Characteristic Curves (T =25°C unless otherwise noted) (Continued) A Figure 3 - Peak Pulse Power Derating Curve Figure 4 - Pulse Waveform 150 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (I PP) Derating in Percentage % 100 80 60 40 20 0 0 25 50 75 100 125 150 tr=10µsec Peak Value IPPM 100 Half Value IPPM IPPM ( ) 2 50 0 175 10/1000µsec. Waveform as defined by R.E.A td 1.0 0 4.0 1000 Transient Thermal Impedance (°C/W) Uni-dire onal V=0V Bi-direc 1000.00 nal V=0V 100.00 Uni-dire onal Bi-direc nal V=VR 10.00 1.00 1.00 10.00 100.00 V BR—Reverse Breakdown Voltage(V) 100 10 1 0.1 0.001 1000.00 0.01 0.1 1 10 100 1000 TP - Pulse Duration (s) Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only Figure 8 - Peak Forward Voltage Drop vs Peak Forward Current (Typical Values) 100.0 120 Single die 100 IF - Peak Forward Current(A) IFSM - Peak Forward Surge Current (A) 3.0 Figure 6 - Typical Transient Thermal Impedance 10000.00 Cj(pf) 2.0 t-Time (ms) TJ - Initial Junction Temperature (ºC) Figure 5 - Typical Junction Capacitance TJ=25°C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM 80 60 40 Stacked-die 10.0 1.0 20 0 1 10 Number of Cycles at 60 Hz 100 0.1 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 VF - Peak Forward Voltage(V) © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BA.06/28/21 TVS Diodes Surface Mount – 600W > P6SMB series Soldering Parameters Pb-Free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 120 secs Average ramp up rate (Liquidus Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max 217°C - Temperature (TL) (Liquidus) Reflow 60 – 150 seconds - Time (min to max) (tL) Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 30 seconds Max Ramp-down Rate 6°C/second Max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 260°C 0.003 ounce, 0.093 grams JEDEC DO214AA. Molded plastic body over glass passivated junction Color band denotes cathode except for bidirectional versions Matte Tin-plated leads, Solderable per JESD22-B102 Case Polarity Terminal Ramp-up TL Critical Zone TL to TP tL Ts(max) Ramp-down Ts(min) ts Preheat 25˚C t 25˚C to Peak Time (t) Environmental Specifications Physical Specifications Weight tp TP Temperature (T) Reflow Condition High Temp. Storage JESD22-A103 HTRB JESD22-A108 Temperature Cycling JESD22-A104 MSL JEDEC-J-STD-020, Level 1 H3TRB JESD22-A101 RSH JESD22-A111 Dimensions DO-214AA (SMB J-Bend) Cathode Band (for Uni-directional products only) C A B H D F E Dimensions Inches Millimeters Min Max Min Max A 0.076 0.086 1.930 2.200 B 0.160 0.187 4.060 4.750 C 0.130 0.155 3.300 3.940 D 0.078 0.103 1.990 2.610 E 0.030 0.060 0.760 1.520 F - 0.008 - 0.203 G 0.205 0.220 5.210 5.590 H 0.006 0.012 0.152 0.305 I 0.089 - 2.260 - J 0.085 - 2.160 - K - 0.107 - 2.740 L 0.085 - 2.160 - G J K L I Solder Pads (all dimensions in mm) © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BA.06/28/21 TVS Diodes Surface Mount – 600W > P6SMB series Part Numbering System P6SMB Part Marking System XXX C A Cathode Band F (for uni-directional products only) 5% VBR Voltage Tolerance XX Bi-Directional YMXXX VBR Voltage Littelfuse Logo Marking Code Trace Code Marking Y:Year Code M: Month Code XXX: Lot Code Series Packaging Component Package DO-214AA Part number P6SMBxxxXX Quantity Packaging Option Packaging Specification 3000 Tape & Reel - 12mm tape/13” reel EIA STD RS-481 Tape and Reel Specification 0.157 (4.0) Cathode 0.47 (12.0) 0.315 (8.0) 0.059 DIA (1.5) Cover tape 13.0 (330) 0.80 (20.2) Arbor Hole Dia. 0.49 (12.5) Dimensions are in inches (and millimeters). Direction of Feed Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics. © 2021 Littelfuse, Inc. Specifications are subject to change without notice. Revised: BA.06/28/21