SL1411A075SM

Gas Discharge Tubes SL1011A and SL1411A Series SL1011A and SL1411A Series RoHS Description The SL1011A and SL1411A series provides high levels of protection against fast rising transients in the 100V/µs to 1kV/µs range usually caused by lightning disturbances. The SL1011A and SL1411A series offers low capacitance (< 1.5pf) which provides low insertion loss at high frequencies. SL1011A offers 5kA protection without destruction whereas the SL1411A offer 10kA surge protection without destruction (maximum single surge of 12kA @ 8/20µs). Agency Approvals AGENCY AGENCY FILE NUMBER Features • Lead-free and RoHS compliant • Low insertion loss • Excellent response to fast rising transients • Ultra low capacitance E128662 2 Electrode GDT Graphical Symbol • 5kA (SL1011A) or 10kA (SL1411A) surge capability tested with 8/20μs pulse as defined by IEC 61000-4-5 2nd edition Applications • Broadband equipment • ADSL equipment • XDSL equipment Additional Information Datasheet SL1011A Resources SL1011A Samples SL1011A SL1011A Datasheet SL1411A Resources SL1411A Samples SL1411A SL1411A © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/12/17 • Satellite and CATV equipment • General telecom equipment Gas Discharge Tubes SL1011A and SL1411A Series Electrical Characteristics Device Specifications (at 25°C) Part Number (@100V/µs) (@1kV/µs) MIN TYP MAX MAX 60 75 90 500 700 72 90 108 500 600 SL1011A145 116 145 174 500 650 120 150 180 500 650 184 230 276 550 700 SL1011A075 SL1411A075 SL1011A090 SL1411A090 SL1011A150 SL1411A150 SL1011A230 SL1411A230 SL1011A250 SL1411A250 200 250 300 600 MIN 800 600 800 280 350 420 800 900 376 470 564 1000 1100 SL1011A500 400 500 600 1100 1200 1200 1400 SL1411A350 SL1011A470 SL1411A470 SL1011A600 SL1411A600 Arc Voltage (on state Voltage) @1Amp Min MAX 480 600 720 Surge Life Nominal Impulse Discharge (@100A 10/1000µs) Current Nominal AC DC AC Dischage Holdover Discharge Current Voltage4 Current (9 Cycles @ (8/20µs) (10x1s @50-60Hz) Max Impulse Discharge Current (1 Application) 50Hz) TYP TYP @ 8/20µs @ 10/350µs SL1411A: 12 kA 1 kA 1010 Ω (at 50V) 50 V 1.5 pF 10 Ω (at 100V) 10 SL1011A260 210 260 310 SL1011A350 Life Ratings Impulse Impulse Insulation CapaciDC Breakdown Breakdown Breakdown Resistance tance in Volts1,2 in Volts3 In Volts (@100V/s) (@1MHz) ~20 V 300 shots SL1011A: 10 shots (@5kA) SL1411A: 10 shots (@10kA) SL1011A: 5A SL1011A: 20 A SL1411A: 10 A SL1411A: 65 A 135 V Notes: 1. At delivery AQL 0.65 level II, DIN ISO 2859 2. In ionized mode 3. Comparable to the silicon measurement Switching Voltage (Vs) 4. Tested according to ITU-T Rec. K.12 < 150 msecs. Product Characteristics Materials Leaded Device: Nickel-plated with Tinplated wires Core and Surface Mount: Dull Tin-plated Product Marking Littelfuse 'LF' Mark, voltage and date code Glow to Arc Transition Current < 0.5 Amps Glow Voltage ~60 Volts Storage and Operational Temperature -40 to +90°C © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/12/17 Gas Discharge Tubes SL1011A and SL1411A Series Device Dimensions For SL1011A Series: 'A' Type Axial Lead Devices PROFILE VIEW 'C' Type Core Devices TOP VIEW TOP VIEW PROFILE VIEW Ø8.0 ± 0.2 [0.315 ± 0.0079] Ø0.8 [0.031] 6.05 ± 0.2 [0.238 ± 0.0079] Ø8.0 ± 0.2 Ø8.0 ± 0.2 [0.315 ± 0.0079] SEMI–PROFILE VIEW 6.05 ± 0.2 [0.238 ± 0.0079] 62 ± 2 For SL1411A series: 'A' Type Axial Lead Devices PROFILE VIEW 'SM' Type Surface Mount Devices TOP VIEW TOP VIEW PROFILE VIEW 8.3 ± 0.1 4 [0.157] Ø1.0 [0.039] + 0.10 Ø8.0 – 0.30 0.0039 [0.315 + – 0.0118 ] 5.55 [0.219] Ø8.3 ± 0.15 6.05 ± 0.2 [0.238 ± 0.0079] 6.05 ± 0.2 [0.238 ± 0.0079] 9. Ø 62 ± 2 SEMI–PROFILE VIEW 30 0.5 ± 0.1 ± 2 0. SOLDER PAD LAYOUT 1.30 [0.051] 'C' Type Core Devices 7.00 [0.276] TOP VIEW PROFILE VIEW + 0.10 Ø8.00 – 0.30 0.0039 [0.315 + – 0.0118 ] SEMI–PROFILE VIEW + 0.10 Ø8.00 – 0.30 + 0.20 6.05 – 0.15 0.0079 [0.238 + – 0.0059 ] © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/12/17 5.40 [0.213] Gas Discharge Tubes SL1011A and SL1411A Series Soldering Parameters - Reflow Soldering (Surface Mount Devices) Pb-free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (Min to Max) (ts) 60 – 180 seconds Average Ramp-up Rate (Liquidus Temp (TL) to peak) 3°C/second max. TS(max) to TL - Ramp-up Rate 5°C/second max. Reflow - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds 260+0/-5 °C Time within 5°C of Actual Peak Temperature (tp) 10 – 30 seconds Ramp-down Rate 6°C/second max. Time 25°C to Peak Temperature (TP) 8 minutes max. Do not exceed 260°C Critical Zone TL to TP Ramp-up TL TS(max) tL Ramp-down Preheat TS(min) 25 Peak Temperature (TP) tP TP Temperature Reflow Condition tS time to peak temperature (t 25ºC to peak) Time Soldering Parameters - Wave Soldering (Thru-Hole Devices) Recommended Process Parameters: 280 Wave Parameter 260 240 Lead-Free Recommendation Preheat: 220 (Depends on Flux Activation Temperature) 200 180 160 140 120 100 80 60 (Typical Industry Recommendation) Temperature Minimum: 100° C Temperature Maximum: Preheat Time: 150° C 60-180 seconds Solder Pot Temperature: 280° C Maximum Solder Dwell Time: 2-5 seconds 40 230 240 220 210 200 190 180 170 160 150 140 130 120 110 90 100 80 70 60 50 40 20 0 0 30 20 10 Temperature (°C) - Measured on bottom side of board 300 Time (Seconds) Cooling Time Preheat Time Dwell Time Soldering Parameters - Hand Soldering Solder Iron Temperature: 350° C +/- 5°C Heating Time: 5 seconds max. © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/12/17 Gas Discharge Tubes < 0.7 Max. SL1011A and SL1411A Series 52.5 ± 1.5 [2.066 ± 0.059] 22.8 [0.898] 6±1 [0.236 ± 0.039] 10 ± 0.5 Pitch [0.394 ± 0.020] Packaging Dimensions For Axial Lead Items Dimensions are in millimeters [and inches] Dimensions are in millimeters [and inches] < 1.2 Max. Lead Bend 254.0 - 356.0 [10.0 - 14.0] < 0.7 Max. Direction of Feed 77.0 Max. [3.03] 52.5 ± 1.5 [2.066 ± 0.059] 22.8 [0.898] 6±1 [0.236 ± 0.039] 10 ± 0.5 Pitch [0.394 ± 0.020] For 'SM' Type Surface Mount Items (SL1411A series only) Dimensions are in millimeters [and inches] 254.0 - 356.0 [10.0 - 14.0] 0.4 ± 0.05 [0.016 ± 0.002] 77.0 Max. 8.5 ± 0.1 [0.335 ± 0.004] [3.03] 1.75 ± 0.1 [0.069 ± 0.004] Dimensions are in millimeters [and inches] 275.0 [10.83] 10x4 ± 0.1 = 40 ± 0.2 [10x0.157 ± 0.004 = 1.575 ± 0.008] 7.5 ± 0.1 [0.295 ± 0.004] 100.0 [3.94] 4 ± 0.1 [0.157 ± 0.004] 1.5 DIA. MAX. [0.059] 76.0 [2.99] 25.0 [0.98] Direction of Feed 17.7 [0.697] 16 +0.3 / -0.1 [0.630 +0.012 / -0.004] Direction of Feed 8.6 ± 0.1 [0.339 ± 0.004] 1.5 DIA. MAX. [0.059] 12 ± 0.1 [0.472 ± 0.004] For 'C' Type Core Items: Packed in plastic bag (500 pcs) © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/12/17 SL1011B XXX X Gas Discharge Tubes SL1011A and SL1411A Series Voltage Pin Configuration A = Axial Lead C = Core Remarks: Formed leads are available on request Part Numbering System and Ordering Information For SL1011A series: For SL1411A series: SL1011A XXX X SL1411 A XXX XX Voltage Surge Capability Pin Configuration Voltage A = Axial Lead C = Core Remarks: Formed leads are available on request Pin Configuration A = Axial Lead C = Core SM = Surface Mount For SL1011B series: SL1011B XXX X Voltage Pin Configuration A = Axial Lead C = Core Remarks: Formed leads are available on request For SL1411A series: SL1411 A XXX XX Surge Capability Voltage Pin Configuration A = Axial Lead C = Core SM = Surface Mount Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics. © 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 12/12/17