HMF51232M4Y-120

HANBit HMF51232M4Y FLASH-ROM MODULE 2MByte (512K x 32-Bit) Part No. HMF51232M4Y GENERAL DESCRIPTION The HMF51232M4Y is a high-speed flash read only memory (FROM) module containing 524,288 words organized in a x32bit configuration. The module consists of four 512Kx 8 FROM mounted on a 72-pin, single-sided, FR4-printed circuit board. Commands are written to the command register using standard microprocessor write timings. Register contents serve as input to an internal state-machine, which controls the erase and programming circuitry. Write cycles also internally latch addresses and data needed for the programming and erase operations. Reading data out of the device is similar to reading from 12.0V flash or EPROM devices. Four chip enable inputs, (/CE_UU2, /CE_UM2, /CE_LM2, /CE_LL2) are used to enable the module’s 4 bytes independently. Output enable (/OE) and write enable (/WE) can set the memory input and output. When FROM module is disable condition, the module is becoming power standby mode, system designer can get low-power design. All module components may be powered from a single +5V DC power supply and all inputs and outputs are TTL-compatible. FEATURES w Access time : 55,70, 90 and 120ns w High-density 2MByte design w High-reliability, low-power design w Single + 5V ± 0.5V power supply w Easy memory expansion wAll inputs and outputs are TTLcompatible w FR4-PCB design w Low profile 72-pin SIMM w Minimum 1,000,000 write/erase cycle w Sector erases architecture w Sector group protection w Temporary sector group unprotection PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 - 55 - 70 - 90 - 120 18 19 20 21 22 23 M 24 Vss A3 A2 A1 A0 Vcc A11 /OE A10 Vcc PIN ASSIGNMENT SYMBOL PIN 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 SYMBOL Vcc DQ8 DQ9 DQ10 /CE_LM2 Vcc NC DQ15 DQ14 DQ13 DQ12 DQ11 A18 A16 Vss A6 Vcc A5 A4 Vcc /CE_UM2 NC DQ23 DQ16 72-PIN SIMM TOP VIEW PIN 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 SYMBOL DQ17 DQ18 DQ22 DQ21 DQ20 DQ19 Vcc A15 A12 A7 Vcc A8 A9 DQ24 DQ25 DQ26 /CE_UU2 NC DQ31 DQ30 DQ29 DQ28 DQ27 Vss /CE_LL2 NC DQ7 DQ0 DQ1 DQ2 DQ6 DQ5 DQ4 DQ3 /WE A17 A14 A13 OPTIONS w Timing 55ns access 70ns access 90ns access 120ns access w Package 72-pin SIMM MARKING FUNCTIONAL BLOCK DIAGRAM URL: www.hbe.co.kr REV.02(August,2002) 1 HANBit Electronics Co., Ltd. HANBit HMF51232M4Y DQ0 - DQ31 A0 - A18 32 19 A0-18 /WE /OE /CE DQ 0-7 U1 /CE_LL2 A0-18 /WE /OE /CE /CE_LM2 A0-18 /WE /OE /CE /CE_UM2 A0-18 /WE /OE /WE /OE /CE /CE_UU2 DQ24-31 DQ16-23 DQ 8-15 U2 U3 U4 TRUTH TABLE MODE STANDBY NOT SELECTED READ W RITE Note : X means don't care /OE X H L X /CE H L L L /WE X H H L DQ HIGH-Z HIGH-Z Dout Din POWER STANDBY ACTIVE ACTIVE ACTIVE URL: www.hbe.co.kr REV.02(August,2002) 2 HANBit Electronics Co., Ltd. HANBit ABSOLUTE MAXIMUM RATINGS PARAMETER Voltage with respect to ground all other pins Voltage with respect to ground Vcc Storage Temperature SYMBOL VIN,OUT VCC TSTG HMF51232M4Y RATING -2.0V to +7.0V -2.0V to +7.0V -65oC to +125oC Operating Temperature TA -55oC to +125oC w Stresses greater than those listed under " Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operating section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. RECOMMENDED DC OPERATING CONDITIONS PARAMETER Vcc for ±5% device Supply Voltages Vcc for ± 10% device Supply Voltages Ground SYMBOL VCC Vcc VSS MIN 4.75V 4.5V 0 0 TYP. MAX 5.25V 5.5V 0 DC AND OPERATING CHARACTERISTICS (0oC ≤ TA ≤ 70 oC ; Vcc = 5V ± 0.5V ) PARAMETER Input Leakage Current Output Leakage Current Output High Voltage Output Low Voltage Vcc Active Current for Read(1) Vcc Active Current for Program /CE = VIL, /OE=VIH or Erase(2) Vcc Standby Current Low Vcc Lock-Out Voltage Notes : 1. The Icc current listed is typically less than 2mA/MHz, with /OE at VIH. 2. Icc active while embedded algorithm (program or erase) is in progress 3. Maximum Icc current specifications are tested with Vcc=Vcc max /CE= VIH ICC3 VLKO 4 3.2 20 4.2 mA V ICC2 120 160 mA TEST CONDITIONS Vcc=Vcc max, VIN= GND to Vcc Vcc=Vcc max, VOUT= GND to Vcc IOH = -2.5mA, Vcc = Vcc min IOL = 12mA, Vcc =Vcc min /CE = VIL, /OE=VIH, SYMBOL IL1 IL0 VOH VOL ICC1 80 2.4 0.45 120 MIN MAX ±1.0 ±1.0 UNITS µA µA V V mA URL: www.hbe.co.kr REV.02(August,2002) 3 HANBit Electronics Co., Ltd. HANBit ERASE AND PROGRAMMING PERFORMANCE LIMITS PARAMETER MIN. Sector Erase Time TYP. 1 MAX. UNIT HMF51232M4Y COMMENTS Excludes 00H programming 8 sec prior to erasure Excludes system-level Byte Programming Time - 7 300 us overhead Excludes system-level Chip Programming Time - 3.6 10.8 sec overhead CAPACITANCE PARAMETER SYMBOL CIN COUT CIN2 PARAMETER TEST SETUP DESCRIPTION Input Capacitance Output Capacitance Control Pin Capacitance VIN = 0 VOUT = 0 VIN = 0 6 8.5 7.5 7.5 12 9 pF pF pF TYP. MAX UNIT Notes : Test conditions TA = 25o C, f=1.0 MHz. TEST CONDITIONS TEST CONDITION Output load Output load Capacitance, CL Input Rise and Fall Times Input Pulse Levels Input timing measurement reference levels Output timing measurement reference levels 30 5 0~3 1.5 1.5 -55 1 TTL gate 100 20 0.45~2.4 0.8 2.0 pF ns V V V ALL OTHERS UNIT URL: www.hbe.co.kr REV.02(August,2002) 4 HANBit Electronics Co., Ltd. HANBit AC CHARACTERISTICS u Read Only Operations Characteristics PARAMETER SYMBOLS tRC tACC Address to Output Delay /OE = VIL tCE tOE tDF tDF Chip Enable to Output Delay Chip Enable to Output Delay Chip Enable to Output High-Z Output Enable to Output High-Z Output Hold Time From Addresses, tQH /CE or /OE, Whichever Occurs First 0 0 0 18 0 /OE = VIL 55 30 0 20 70 30 0 DESCRIPTION SETUP Read Cycle Time /CE = VIL MIN 55 55 MAX MIN 70 70 MAX MIN 90 TEST -55 -70 -90 HMF51232M4Y -120 MAX MIN 120 90 90 35 0 20 35 120 120 50 MAX UNIT ns ns ns ns ns ns 0 ns 5.0V 2.7kΩ Device Under Test CL IN3064 or Equivalent 6.2kΩ Diodes = IN3064 or Equivalent Note : CL = 100pF including jig capacitance u Erase/Program Operations PARAMETER SYMBOLS tWC tAS tAH tDS DESCRIPTION MIN W rite Cycle Time Address Setup Time Address Hold Time Data Setup Time 40 25 45 30 55 TYP MIN 70 0 45 45 50 50 HANBit Electronics Co., Ltd. -55 -70 MAX MIN 90 -90 MAX MIN 120 -120 UNIT MAX ns ns ns ns URL: www.hbe.co.kr REV.02(August,2002) 5 HANBit tDH tOES tGHWL tCS tCH tWP tWPH tWHWH1 tWHWH2 tVCS Notes : 1. This does not include the preprogramming time 2. This timing is only for Sector Protect operations Data Hold Time Output Enable Setup Time Read Recover Time Before Write /CE Setup Time /CE Hold Time W rite Pulse Width W rite Pulse Width High Byte Programming Operation Sector Erase Operation (Note1) Vcc set up time 30 35 20 7 1 50 0 0 0 0 0 45 HMF51232M4Y ns ns ns ns ns 50 ns ns µs sec µs u Erase/Program Operations Alternate /CE Controlled Writes PARAMETER SYMBOLS tWC tAS tAH tDS tDH tGHEL tWS tWH tCP tCPH tWHWH1 tWHWH2 DESCRIPTION MIN W rite Cycle Time Address Setup Time Address Hold Time Data Setup Time Data Hold Time Read Recover Time Before Write /WE Setup Time /WE Hold Time /CE Pulse Width /CE Pulse Width High Byte Programming Operation Sector Erase Operation (Note) 30 ns 35 20 7 1 40 25 ns ns 45 30 0 0 0 0 45 50 55 TYP ns MIN 70 0 45 45 50 50 MAX MIN 90 MAX MIN 120 MAX ns ns ns ns ns ns ns ns ns ns µs sec -55 -70 -90 -120 UNIT Notes : This does not include the preprogramming time. URL: www.hbe.co.kr REV.02(August,2002) 6 HANBit Electronics Co., Ltd. HANBit u READ OPERATIONS TIMING HMF51232M4Y u RESET TIMING URL: www.hbe.co.kr REV.02(August,2002) 7 HANBit Electronics Co., Ltd. HANBit u PROGRAM OPERATIONS TIMING HMF51232M4Y u CHIP/SECTOR ERASE OPERATION TIMINGS URL: www.hbe.co.kr REV.02(August,2002) 8 HANBit Electronics Co., Ltd. HANBit u DATA# POLLING TIMES(DURING EMBEDDED ALGORITHMS) HMF51232M4Y u TOGGLE# BIT TIMINGS (DURING EMBEDDED ALGORITHMS) URL: www.hbe.co.kr REV.02(August,2002) 9 HANBit Electronics Co., Ltd. HANBit u SECTOR PROTECT UNPROTECT TIMEING DIAGRAM HMF51232M4Y u ALTERNATE CE# CONTROLLED WRITE OPERATING TIMINGS URL: www.hbe.co.kr REV.02(August,2002) 10 HANBit Electronics Co., Ltd. HANBit PACKAGE DIMENSIONS HMF51232M4Y 0.25 mm MAX 2.54 mm MIN 1.27±0.08mm 1.27 Gold: 1.04±0.10 mm Solder: 0.914±0.10 mm (Solder & Gold Plating) ODERING INFORMATION Part Number Density Org. Package Component Number 4EA 4EA 4EA 4EA Vcc SPEED HMF51232M4Y-55 HMF51232M4Y-70 HMF51232M4Y-90 HMF51232M4Y-120 2MByte 2MByte 2MByte 2MByte 512K×32bit 512K×32bit 512K×32bit 512K×32bit 72 Pin-SIMM 72 Pin-SIMM 72 Pin-SIMM 72 Pin-SIMM 5.0V 5.0V 5.0V 5.0V 55ns 70ns 90ns 120ns URL: www.hbe.co.kr REV.02(August,2002) 11 HANBit Electronics Co., Ltd.