M20-7873842P

C00116 COMPONENT SPECIFICATION M20 SERIES CONNECTORS AUGUST 2016 CONTENTS: SECTION TITLE PAGE 1 Description of Connector and Intended Application 2 2 Marking of Connector and/or Package 2 3 Ratings 3 Appendix 1 Gauges 5 APPENDICES NOTES: 1. 2. 3. 4. Third angle projection is used where projected views are shown. All dimensions are in millimetres. For explanation of dimensions, etc. see BS8888. Unless otherwise stated, all dimensions are maxima. Matthew Perren PREPARED BY: ............................................... Sam Bennett APPROVED BY: ................................................ C00116 Date: 31-08-2016 C/Note: 20036 Issue: 16 C00116 COMPONENT SPECIFICATION M20 SERIES CONNECTORS 1. DESCRIPTION OF CONNECTOR AND INTENDED APPLICATION. A range of 2.54mm (0.1”) pitch connectors, having 0.64mm (0.025”) square pins and sockets suitable for interconnecting board to board and board to wire. The socket is a box section design with a latch to locate and hold in an insulated housing. Terminations are available for wire crimp, through board solder or surface mount in either horizontal or vertical mounting. The plug pin is held in a moulding, and is available for either horizontal or vertical, surface mount or through board solder mounting. Plug mouldings are available in unlatched or latched versions. Contacts may be gold. Surface mountable pin headers are available in single and double row, vertical and horizontal variations. 2. MARKING OF THE CONNECTOR AND/OR PACKAGE (ORDER CODE). The marking (order code) shall appear on the package and shall be of the following style: M20 XXX XX XX Product Group Connector Style No. of Contacts per row Contact Finish The marking (order code) for a pin header variant shall appear on the package and shall be of the following style: M20 - XXX XXX X XX XX Product Group Dimension A Dimension B Connector Style No. of Contacts per row Contact Finish For details of Connector Style, Finish and No. Of Contacts per row, see individual drawings or Harwin catalogue. -2C00116 Date: 31-08-2016 C/Note: 20036 Issue: 16 C00116 COMPONENT SPECIFICATION M20 SERIES CONNECTORS 3. RATINGS. For all M20 Pin Headers, including Pin header variants (detailed below as “M20-PH”). Note: individual components may exceed above ratings – check individual customer information sheets. 3.1. MATERIAL & FINISH. Moulding Material: For PC Tail or SMT connectors ................................ High Temperature Thermoplastic, UL94V-0 For Cable connectors............................................... See individual drawing Contact Material ............................................................. Copper alloy Contact Finish.................................................................. See individual drawing 3.2. ELECTRICAL CHARACTERISTICS. Current Rating (per contact) ...................................................................................... 3A max Contact Resistance (initial) ........................................................................................ 20mΩ max Contact Resistance (after conditioning) .................................................................... 30mΩ max Dielectric Withstanding Voltage (Voltage Proof): M20-875…………………………………………………………………………………..500V AC, for 1 minute M20-PH (SMT), M20-786/787 ........................................................... 800V AC, for 1 minute M20-106/107/116/118 ....................................................................... 1,500V AC for 1 minute Other .................................................................................................. 1,000V AC for 1 minute Insulation Resistance: M20-PH (SMT) ..................................................................................................... 500MΩ min M20-106/107/116/118 ......................................................................................... 5,000MΩ min Other .................................................................................................................... 1,000MΩ min 3.3. ENVIRONMENTAL CHARACTERISTICS. Operating Temperature Range ........................................................................................ -40°C to +105°C Vibration: M20-PH/781/782/783/786/787/788/789/791/792/889/890/891………...50-2000Hz, 3.13Grms, Duration 15 mins in each axis Other .......................................................................................... ….............Not tested Shock: M20-PH/781/782/783/786/787/788/789/791/792/889/890/891 .................... 30G for 11ms Other .................................................................................................................... Not tested -3C00116 Date: 31-08-2016 C/Note: 20036 Issue: 16 C00116 COMPONENT SPECIFICATION M20 SERIES CONNECTORS 3. RATINGS (continued). 3.4. MECHANICAL CHARACTERISTICS. Durability: M20-PH/786/787/788/789/890 ......................................................................... 300 operations Other .................................................................................................................... 300 operations for gold 50 operations for tin Insertion force (maximum): M20-116/118 ........................................................................................................ 1.2N per contact M20-782/783/786/787/788/789/889 ................................................................ 2.0N per contact Withdrawal force (minimum): M20-116/118/781/782/783/786/787/788/789/791/792/889............................ 0.3N per contact Contact Retention force (minimum)..........................................................................7.84N per contact Contact Crimp pull-off forces: Wire Gauge 30 AWG 28 AWG 26 AWG 24 AWG 22 AWG Minimum pull-off force (Newtons) 9N 11N 18N 29N 45N 3.5. SOLDERING DATA. Solderability (for PC Tail & SMT products) ................................................................... 245°C for 5 seconds Soldering heat resistance (for PC Tail & SMT products) ........................................... 260°C for 10 seconds -4C00116 Date: 31-08-2016 C/Note: 20036 Issue: 16 C00116 COMPONENT SPECIFICATION M20 SERIES CONNECTORS APPENDIX 1 - GAUGES. NOTES: 1. 2. 3. 4. Material = Steel to BS1407 or equivalent. Gauging surfaces to be hardened/ground, 650 HV5 min. These gauges to be used for testing fully assembled components only. Ultimate wear limit 0.005mm is allowable on gauging dimensions. CONTACT PUSH-OUT GAUGE. LAP 0.2 4.40 +0.00 -0.05 LAP 0.2 11.0 10.0 3.75 +0.00 -0.05 -5C00116 Date: 31-08-2016 C/Note: 20036 Issue: 16