HF3-34CVFA

Cover (HIF3B Series) against EMI (Electromagnetic Interference) sFeatures 1. Electromagnetic Shielding Effect This product enhances shielding effects with a metallic cover over the ribbon cable connector (HIF3B series). sApplications Peripheral and termination equipment, control machines, measuring instruments etc. sOrdering Information 2. Screw Locking Mechanism The locking mechanism is designed in a stubborn and steady structure for the screw type. 3. Assembling The ribbon cable connector (HIF3B series) can be easily assembled. HIF 3 - * CVFA q q Series Name e CVFA : HIF 3 : Cover case for EMI w e w Number of contacts : 10, 16, 20, 26, 30, 34, 40, 50, 64 sI/O Cable Termination sMaterial Material Zinc alloy Finish Nickel plated As shown above, bend the shield knitted cord, wind the conductive tape 1 to 2 turns, and finish cable termination so as not to loosen the shield knitted cord. B45 sCover Unit : mm Part Number HIF3-10CVFA HIF3-16CVFA HIF3-20CVFA HIF3-26CVFA HIF3-30CVFA HIF3-34CVFA HIF3-40CVFA HIF3-50CVFA HIF3-64CVFA CL No. 612-0061-4 612-0062-7 612-0063-0 612-0064-2 612-0065-5 612-0066-8 612-0067-0 612-0068-3 612-0070-5 Number of Contacts 10 16 20 26 30 34 40 50 64 A 8.5 7.8 9.0 10.0 9.2 11.0 13.0 14.5 15.4 B 8.0 7.8 8.5 9.5 9.2 10.0 10.0 10.0 10.0 C 31.7 34.9 39.98 47.6 52.68 57.76 65.38 78.08 D E 38.12 17.52 41.32 25.14 46.4 59.1 71.8 84.5 30.22 42.92 55.62 68.32 86.1 54.02 37.84 64.18 48.0 95.86 102.7 B46 sApplicable Socket Connector Notes1 and 2: The number of polarizing guide and keys change according to products. Unit : mm Part Number HIF3BA-10D-2.54R-CL(21) HIF3BA-16D-2.54R-CL(21) HIF3BA-20D-2.54R-CL(21) HIF3BA-26D-2.54R-CL(21) HIF3BA-30D-2.54R-CL(21) HIF3BA-34D-2.54R-CL(21) HIF3BA-40D-2.54R-CL(21) HIF3BA-50D-2.54R-CL(21) HIF3BB-50D-2.54R-CL(21) HIF3BA-64D-2.54R-CL(21) HIF3BB-64D-2.54R-CL(21) CL No. 610-0190-4-21 610-0192-0-21 610-0193-2-21 610-0194-5-21 610-0195-8-21 610-0196-0-21 610-0197-3-21 610-0198-6-21 610-0201-9-21 610-0200-6-21 610-0203-4-21 Number of Contacts 10 16 20 26 30 34 40 50 50 64 64 A B C D Polarizing guide Polarizing keyway One at center 17.27 10.16 11.43 12.8 24.89 17.78 19.05 20.42 29.97 22.86 24.13 25.5 37.59 30.48 31.75 33.12 42.67 35.56 36.83 38.2 47.75 40.64 41.91 43.28 55.37 48.26 49.53 50.9 68.07 60.96 62.23 63.6 68.07 60.96 62.23 63.6 85.85 78.74 80.01 81.38 One on right and left sides, resp. One at center One at center One on right and left sides, resp. One at center 85.85 78.74 80.01 81.38 One on right and left sides, resp sPin Header The pin header applicable to the socket connector HIF series can wholly use the HIF3 series. It is recommended to use following products, considering positioning (protection of mating area) when the connector is engaged. In addition, when the connector is installed, the locking mechanism is removed. If needed, order the product (11) according to the specification (unlock), as shown below. HIF3B –*PA–2.54DS,DSA(11) HIF3BA–*PA–2.54DS,DSA(11) HIF3BB–*PA–2.54DS,DSA(11) Note: HIF3B–*PA–2.54DS, DSA (11) is limited to number of contacts as follows: DSA-20, 30, 34, 40 contacts DSA-26, 50 contacts B47 sRecommended Panel catouts Number of Contacts 10 16 20 26 30 34 40 50 64 A B C 10.16 17.78 30.48 D 21.8 29.5 34.5 42.2 47.2 52.3 59.9 72.6 90.4 18.52 31.7 26.14 34.9 38.84 47.6 49.0 31.22 39.98 22.86 43.92 52.68 35.56 57.76 40.64 56.62 65.38 48.26 69.32 78.08 60.96 87.1 95.86 78.74 q Right Angle Type HIF3B-*PA-DS(11) HIF3BA-*PA-DS(11) 3BB 3.45 4.75 B48 sCover Assembling Procedures 4 5 2 1 6 3 1 7 8 3 BAssembling Procedures 1. Insert the connected connector (cable shield cable after termination process) 1 in the adapter metal 2, and connect the assembly to the cover A 3. 2. Insert the cable unit 1 in the clamp slot of cover A 3, and mount the clamp metal 4. Then, tighten the unit by screws. 3. Next, place the lock screw 5 in the right slot, and mount the cover B 7 so as not to bite the cable, and tighten the assembly by screws. At this time, check that no clearance is found between cover A and B. B49