TM21R-5B-3232D-LP

NEW Modular Jack Connectors for High-Speed LAN Transmission TM21R Series Built-in Optical Indicators LED Optical indicator Optical pipe sFeatures 1. Supports High-Speed LAN Transmission Meets requirements of TIA/EIA-568-B data wiring standard. Single port configuration meeting CAT5e and multiple port configuration meeting CAT5 transmission performance. As such, these products fully support Gigabit Ethernet (1000BASE-T) and Fast Ethernet (100BASE-TX) highspeed LAN transmission. Housing Optical indicator area Space saving Optical indicator 2. Built-in Optical Indicators Optical indicators are integral part of the connectors saving space on customer’s board. Compared with LED type indicators, they do not emit any electrical noise. 3. EMI protection Metal shield covers the outer surfaces of the connectors assuring complete protection against electromagnetic interference. Built-in multiple shield and ground contacts assure reliable connection with the mounting panel as well as with the mating connector. One additional TM21 multi-port jack can be mounted in the space previously occupied by LEDs. 4. FCC Standards Meets requirements of FCC Title 47, Part 68, Subpart F. sApplications Telecom Hubs, Routers, Bridges and ATM Transmission Equipment, Ethernet Switches and Networking Equipment, Test and Measurement Equipment, Medical Diagnostic Equipment. Built-in LED type (Possibility of electromagnetic noise emission and interference.) Built-in Optical pipe type (No electromagnetic noise emission.) 2002.11 1 sProduct Specifications Current rating Ratings Voltage rating 125 V AC 1A Operating temperature range-25ç to +80ç (Note) Item 01.Insulation resistance 100 M ohms min Specification 100 V DC 500 V AC / one minute Conditions 02.Dielectric Withstanding Voltage No flashover or insulation breakdown (between adjacent contacts) 03.Withstanding voltage No flashover or insulation breakdown (between contact and shield) 04.Contact resistance 05.Vibration 230 m ohms max. No electrical discontinuity of 5 ms or more Contact resistance: 250m ohms max. No electrical discontinuity of 5ms or more Contact resistance: 250m ohms max. Contact resistance: 250m ohms max. 1500 V AC / one minute 100mA DC Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours / 3 axis Acceleration of 490 m/s2, 11 ms duration, sine half-wave waveform, 3 cycles in each of the 3 axis 200 cycles (Temperature: -55ç/+5ç to +35ç/+85ç/+5ç to +35ç Duration: 30 / 5 / 30 / 5 (Minutes) 5 cycles 06.Shock 07.Durability (mating/unmating) 08.Temperature cycle Contact resistance: 250 m ohms max. Insulation resistance: 100 M ohms min. Contact resistance: 250 m ohms max. Insulation resistance: 1 M ohms min. (High humidity) Insulation resistance: 10 M ohms min. (Dry state) Contact resistance: 250 m ohms max. 09.Humidity 500 hours at temperature of 40ç and humidity of 90% to 95% 10.Salt Spray Exposed to density 5% salt water for 48 hours Note :Includes temperature rise caused by current flow. sMaterials Part Insulator Contact Optical pipe Shield Material PBT Copper alloy Poly carbonate Copper alloy Finish Color: Black Contact area: Gold plating Termination area: Solder plating Color: Clear Tin plating Remarks UL94V-0 ------------------- sOrdering information qJacks TM21 R - 5 A - 32 32 D - LP 1 2 3 4 5 6 7 8 q Series Name w Connector type e Jack type number r Jack performance level code TM21 R : Jack 5 : PCB Right-angle through hole type A : CAT5 (Single row, multi-port) B : CAT5 (Double row, multi port) C : Supports CAT5e (Single port) t Jack opening code 8 : 8 contacts 32 : 8 contacts /4 ports 48 : 8 contact/6 ports y Number of inserted contacts 8 : 8 contact 32 : 8 contact inserted in 4 ports=32 contacts 48 : 8 contact inserted in 6 ports=48 contacts u Number of rows Blank: Single row D: Double row i Optical pipe LP: With optical pipe inserted Blank: Without optical pipe 2 sModular Jack Connectors Supporting CAT5e qSingle Port With Built-in Optical Pipe 16 Contact No.8 Contact No.1 0.8 21 (5.5) 13.75 13.4 3 3.6 0.8 (2.8) 1 3.05 10.25 6.35 13.05 24 0.35 2.54 0.45 11.43 15.75 0.8 0.25 0.8 Contact No.8 11.9 Part Number TM21R-5C-88-LP CL No. 222-2892-0 qSingle Port Without Optical Pipe 21 16 Contact No.8 Contact No.1 0.8 (5.5) 13.75 13.4 3 3.6 0.8 (2.8) 1 3.05 10.25 6.35 13.05 24 0.35 2.54 0.45 11.43 15.75 0.8 0.25 0.8 Contact No.8 11.9 Part Number TM21R-5C-88 CL No. 222-2893-2 TM21R-5C 1 PC Contact No.7 (5.5) Contact No.1 Contact No.2 (5.5) 1.7 TM21R-5C 1 PC Contact No.7 (5.5) Contact No.1 Contact No.2 (5.5) 1.7 3 BRecommended PCB mounting patterns qWith Built-in Optical Pipe 11.9 8.89 6.35 3.81 1.27 LED location area LED light emission area No ground traces Contact No. 3MIN 8 7 6 5 4 3 1 2 qWithout Optical Pipe 8.89 6.35 3.81 1.27 Contact No. 8 5 6 4 3 1 2 8-Ø 1 2.54 3 8Ø1 .2 Ø3 2- 13.05 6.35 6.35 2- Ø3 3MIN 7 6.75 6.75 6.75 3MIN 3.05 2Ø1 .6 3.05 11.43 15.75 Printed board edge Connector front edge 11.43MIN No conductive traces 2 2Ø1 .6 11.43 15.75 Printed board edge Connector front edge 11.43MIN No conductive traces 2 *Recommendations for PCB Design 1 The contact arrangement differs between the contact area side and Printed board side. (1,2,3,4,5,6,7,8 on the contact are side / 2,1,3,4,5,6,8,7 on the printed board side) 2 Areas indicated should be free of conductive traces. 3 Area indicated should be free of ground traces. 4 Recommended board thickness: 1.6mm. 5 To assure that the indicator light pipes operates correctly the LED 's must be installed directly on the PCB, within recommended dimensions and with light emitting center in upward direction. Contact applicable manufacturer for LED specification. 1 PCB mounting pattern Other Series 7531 TM21R Series 8532 8642 6.75 3MIN .2 2.54 1 1 No ground traces 3 7641 5 Suggested LEDs LED light emitting center 2.7MAX 3.2MAX 1.5MAX BPanel Cutout qFor Both Types, With and Without Built-in Optical Pipe (33) 0.6MIN 4.5MIN TM21P--88P Lock lever TM21R--5C--88--LP 4.5 +1 -2 1 PCB mounting surface 0.15 14.1 Panel side 16.4 1 Connector front surface 1 0 2.8 -0.8 6.75 10.25 *Recommendations for Panel Design 1 The shield contacts should connect with the panel cut-out on all sides. 4 sModular Receptacles Supporting CAT5 qSingle row/ multiple ports, with Built-in Optical Pipe 59.18 41.91 13.97 1 Contact No.1 Contact No.8 25.9 (6) 15.3 1.7 (3.5) 0.35 1.4 2.5 10.25 15.525 8.34 SML-010 Series 10.9 1.6 15.4 Part Number TM21R-5A-3232-LP CL No. 222-2873-5 1 0.45 Contact No.2 0.25 Contact No.1 53.81 58.93 Contact No.7 Contact No.8 1 (6) 3.6 11.9 BRecommended PCB mounting patterns LED Mount Area Dimensions 58.93 41.91 4-Ø2 LED location area LED light emission area 4 CL-220 Series 13.97 8.89 6.35 3.81 1.27 5.8 1.2 11.9 4 1.4 12.7 1.45 1.3 32-Ø1 15.525 5.8 8.34 12.7 1 (6) 0.75 3 12.7 8.34 8.34 1467 2358 SML-020 Series 10.4 2.5 2.7 0.6 6MAX 3MIN Contact No. 1 4-Ø2 2-Ø3.2 No conductive traces 53.81 2 Printed board edge Connector front edge 12.7 *Recommendations for PCB Design 1 The contact arrangement differs between the contact area side and Printed board side. (1,2,3,4,5,6,7,8 on the contact are side / 2,1,3,4,5,6,8,7 on the printed board side) 2 Areas indicated should be free of conductive traces. 3 Recommended board thickness: 1.6mm. 4 To assure that the indicator light pipes operates correctly the LED’s must be installed directly on the PCB, within recommended dimensions and with light emitting center in upward direction. Contact applicable manufacturer for LED specification. 4 Suggested LEDs Series Name CL-220 SML-010 SML-020 Manufacturer Citizen Electronics Co., Ltd. Rohm Co., LTD Rohm Co., LTD 1 PCB mounting pattern 2 4 6 8 1 4 6 7 1 4.4 3 1 5 7 12.7 1.5 2 3 5 8 15.4 5 BRecommended Panel Cutout 0.15 4.5MIN 13.97 41.91 Panels Side 59.6 1 (34) TM21P-- 88P Connector front surface 5 - 2.5 +1 1 Lock lever 3.5 0 -1 6 MAX 10.25 *Recommendations for Panel Design 1 The shield contacts should connect with the panel cut-out on all sides. 6 0.4MIN Shield spring contact 15.8 PCB mounting surface qDouble row / multiple port, with Built-in Optical Pipe 1 A B 13.97 Contact No.8 32.5 Upper row Contact No.1 27.9 (6) 28 TM21R-5B-3232D-LP 0.45 Contact No.1 0.25 C D (6) 1 Lower row connectors contacts 0.75 3.6 3 Contact No.8 Lower row (6) 1 (3.5) 1.4 2.5 10.25 8.34 5.8 14.94 22.125 0.35 12.4 14.94 1 PBT 2358 1467 7641 8532 TM21R-5B-4848D-LP 11.9 Upper row connectors contacts 7.7 Part Number TM21R-5B-3232D-LP TM21R-5B-4848D-LP CL No. 222-2879-1 222-2885-4 A 59.18 87.12 B 41.91 69.85 C 53.81 81.75 D 58.93 86.87 BRecommended PCB mounting pattern A B 4 Upper row LED mount position Lower row LED mount position 11.9 7.7 LED light emission area E- Ø2 13.97 8.89 6.35 3.81 1.27 Upper row contact hole Lower row contact hole 4 1.2 1.4 1.3 19.3 14.94 6 MAX 3 MIN 2.5 4- Ø2 2- Ø3.2 1 Contact No. No conductive traces C 2 Printed board edge Connector front edge Part Number TM21R-5B-3232D-LP TM21R-5B-4848D-LP CL No. 222-2879-1 222-2885-4 A 58.93 86.87 B 41.91 69.85 C 53.81 81.75 D 64 96 5.8 8.34 1467 2358 E 4 6 *Recommendations for PCB Design 1 The contact arrangement differs between the contact area side and Printed board side. (1,2,3,4,5,6,7,8 on the contact are side / 2,1,3,4,5,6,8,7 on the printed board side) 2 Areas indicated should be free of conductive traces. 3 Recommended board thickness: 1.6mm. 4 To assure that the indicator light pipes operates correctly the LED's must be installed directly on the PCB, within recommended dimensions and with light emitting center in upward direction. Contact applicable manufacturer for LED specification. 1 PCB mounting pattern Other Series 7 8 2 1 3 6 4 5 5 4 6 7 3 2 8 2 1 7 1 3 TM21R Series 8 6 4 5 5 4 6 8 3 1 7 2 4 Suggested LEDs Series Name CL-220 Manufacturer Citizen Electronics Co., Ltd. 12.4 D- Ø1 14.94 8532 7641 22.125 19.3 1.7 28 7 BPanes Cutout 1 Shield spring contact spring PCB mounting surface 0.15 4.5MIN 13.97 Panel Side A B Part Number TM21R-5B-3232D-LP TM21R-5B-4848D-LP CL No. 222-2879-1 222-2885-4 A 41.91 69.85 B 59.60 87.54 (34) 5 +1 -2.5 1 TM21P -- 88P Lock lever TM21R -- 5B -- * * * * D -- LP 1 Connector front surface 6 MAX 1 0 3.5 -1 10.25 *Recommendations for Panel Design 1 The shield contacts should connect with the panel cut-out on all sides. 8 0.4 MIN 28.4 BTechnical Documentation CAT5e Transmission Characteristics Data Representative values of the various transmission characteristics data for fully mated receptacle (TM21R-5C-88-LP) and plug (TM21P-88P). All plugs in the TM21R-5C Series that were manufactured based on the De-embedded method of the TIA/EIA-568-B.2 standard and meet performance requirements of CAT5e single transmission. Note:These data are for the listed connector combination. Inquire with your Hirose Electric account representative about other combinations. qSignal Attenuation 0.5 Attenuation(dB) 0.4 0.3 0.2 0.1 0 0 10 20 30 40 50 60 70 80 90 100 Frequency(MHz) 1,2 3,6 4,5 7,8 CAT5e Spec qNear-End Crosstalk (NEXT) Data 120 100 NEXT(dB) 80 60 40 20 0 0 10 20 30 40 50 60 70 80 90 100 Frequency(MHz) 1,2-3,6 3,6-7,8 1,2-4,5 4,5-7,8 1,2-7,8 CAT5e Spec 3,6-4,5 qReturn Loss 80 60 40 20 0 0 10 20 30 40 50 60 70 80 90 100 Return Loss(dB) Frequency(MHz) 1,2 3,6 4,5 7,8 CAT5e Spec 9 qFar-End Crosstalk (FEXT) 120 100 FEXT(dB) 80 60 40 20 0 0 10 20 30 40 50 60 70 80 90 100 Frequency(MHz) 1,2-3,6 3,6-1,2 4,5-1,2 7,8-1,2 CAT5e Spec 1,2-4,5 3,6-4,5 4,5-3,6 7,8-3,6 1,2-7,8 3,6-7,8 4,5-7,8 7,8-4,5 qPropagation Delay 3 2.5 Delay(ns) 2 1.5 1 0.5 0 0 10 20 30 40 50 60 70 80 90 100 Frequency(MHz) 1,2 3,6 4,5 7,8 CAT5e Spec qPropagation Delay (Delay Skew) 1.4 1.2 Delay Skew(ns) 1 0.8 0.6 0.4 0.2 0 0 10 20 30 40 50 60 70 80 90 100 Frequency(MHz) Measurement Value CAT5e Spec 10 BReference Documentation qCAT6 Certification Received Only the high quality plugs in the TM21R-5C Series (based on the De-embedded method of the TIA/EIA-568-B.2 standard) clear CAT6 single transmission performance. A certificate was issued by the GHMT, independent European testing company. Certificate of Acceptance Return Loss NEXT 11 USA: HIROSE ELECTRIC U.S.A., INC. 2688 Westhills Court, Simi Valley, CA 93065-6235 Phone : 1 805 522 7958 Fax : 1 805 522 3217 http://www.hirose.com GERMANY: EUROPE BRANCH: HIROSE ELECTRIC GmbH HIROSE ELECTRIC CO., LTD. First Class Building 4F, Beechavenue 46.1119PV Zeppelinstrasse 42 D-73760 Ostfildern Kemnat Phone : 49 711 4560021 Schiphol-Rijk, The Netherlands Fax : 49 711 4560729 Phone : 31 20 6557 460 http://www.hirose.de Fax : 31 20 6557 469 http://hiroseeurope.com CHINA: HIROSE ELECTRIC CO., LTD. 10F,No.06, Shanghai Times Square office Tower, 93. Huai Hai Zhong Road, Luwan Shanghai Phone : 86 21 6391 0011 Fax : 86 21 6391 0101 SINGAPORE: HIROSE ELECTRIC CO., LTD. 10 Anson Road #34-13 International Plaza 079903 Phone : 65 6324 6113 Fax : 65 6324 6123 UNITED KINGDOM: KOREA: HIROSE ELECTRIC UK LTD. HIROSE KOREA CO., LTD. Crownhill Business Centre 22 Vincent Avenue (#2NA311,Shihwa Industrial Complex), Crownhill, Milton Keynes MK8 OAB 1261-10, Jeoungwhang-Dong, Shihung-City, Kyunggi-Do Phone : 44 1908 305400 Phone : 82 31 496 7000,7124 Fax : 44 1908 305401 Fax : 82 31 496 7101 http://www.hirose.co.uk http://www.hirose.co.kr HONG KONG: HIROSE ELECTRIC CO., LTD. Unit 506, Energy Plaza. 92 Granville Road, Tsim Sha Tsui East, Kowloon Phone : 852 2803 5338 Fax : 852 2591 6560 TAIWAN: HIROSE ELECTRIC CO., LTD. No.28 Lane 247 Sec. 2 Yen Ping N,Rd.Taipei Phone : 886 2 2557 7351,7352 Fax : 886 2 2552 9851 Crea tiv to World E inks le eL ® 12 The contents of this catalog are current as of date of publication. Contents are subject to change without notice for the purpose of product improvements. s onic ctr HIROSE ELECTRIC CO., LTD. 5-23,OSAKI 5-CHOME,SHINAGAWA-KU,TOKYO 141-8587,JAPAN PHONE: 81-3-3491-9741, FAX: 81-3-3493-2933