HMC483MS8G_10

HMC483MS8G / 483MS8GE v01.0710 HIGH IP3 GaAs MMIC MIXER with INTEGRATED LO AMPLIFIER, 0.7 - 1.5 GHz Typical Applications The HMC483MS8G / HMC483MS8GE is ideal for: • Cellular/3G Features +33 dBm Input IP3 Conversion Loss: 9 dB Low LO Drive: -4 to +4 dBm Single Positive Supply: 5V @ 50 mA Ultra Small MSOP Package: 14.8mm2 Included in the HMC-DK003 Designer’s Kit 10 MIXERS - HIGH IP3 - SMT • GSM, GPRS & EDGE • CDMA & WCDMA • Cable Modem Termination Systems Functional Diagram General Description The HMC483MS8G & HMC483MS8GE are high dynamic range passive MMIC mixers with integrated LO amplifiers in plastic surface mount 8 lead Mini Small Outline Packages (MSOP) covering 0.7 to 1.5 GHz. Excellent input IP3 performance of +33 dBm for down conversion and +30 dBm for up conversion is provided for 2.5G & 3G GSM/CDMA applications at an LO drive of 0 dBm. With an input 1 dB compression of +24 dBm, the RF port will accept a wide range of input signal levels. Conversion loss is 9 dB typical. The DC to 350 MHz IF frequency response will satisfy GSM/CDMA transmit or receive frequency plans configured for low side LO. The HMC483MS8G(E) are pin for pin compatible with the HMC485MS8G(E) which are 1.7 - 2.2 GHz mixers with LO amplifiers. Electrical Specifi cations, TA = +25°C, LO = 0 dBm, IF = 70 MHz*, Vdd= 5V Parameter Frequency Range, RF & LO Frequency Range, IF Conversion Loss Noise Figure (SSB) LO to RF Isolation LO to IF Isolation IP3 (Input) 1 dB Gain Compression (Input) LO Input Drive Level (Typical) Supply Current 10 6 Min. Typ. 0.8 - 1.1 DC - 350 8.5 8.5 20 10 33 24 -4 to +4 50 10.5 10.5 6 6 Max. Min. Typ. 0.7 - 1.5 DC - 350 9 9 14 13 33 23 -4 to +4 50 12 12 Max. Units GHz MHz dB dB dB dB dBm dBm dBm mA *Unless otherwise noted, all measurements performed as a downconverter. 10 - 230 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC483MS8G / 483MS8GE v01.0710 HIGH IP3 GaAs MMIC MIXER with INTEGRATED LO AMPLIFIER, 0.7 - 1.5 GHz Conversion Gain vs. Temperature 0 Isolation 0 CONVERSION GAIN (dB) -5 ISOLATION (dB) -10 10 RF TO IF LO TO RF LO TO IF -10 + 25C + 85C - 40C -20 -15 -30 -20 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5 RF FREQUENCY (GHz) -40 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5 FREQUENCY (GHz) Conversion Gain vs. LO Drive 0 Return Loss 0 CONVERSION GAIN (dB) -10 LO = -6 dBm LO = -4 dBm LO = -2 dBm LO = 0 dBm LO = +2 dBm LO = +4 dBm RETURN LOSS (dB) -5 -5 -10 -15 -15 LO RF -20 0.6 -20 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5 0.6 0.7 0.8 RF FREQUENCY (GHz) 0.9 1 1.1 1.2 FREQUENCY (GHz) 1.3 1.4 1.5 Upconverter Performance Conversion Gain 0 IF Bandwidth 0 CONVERSION GAIN (dB) -5 RESPONSE (dB) -5 CONVERSION GAIN RETURN LOSS -10 LO = -6 dBm LO = -4 dBm LO = -2 dBm LO = 0 dBm LO = +2 dBm LO = +4 dBm -10 -15 -15 -20 0.6 -20 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5 0 80 160 240 320 400 RF FREQUENCY (GHz) IF FREQUENCY (MHz) *Unless otherwise noted, all measurements performed as a downconverter, with low side LO & IF = 70 MHz. F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 10 - 231 MIXERS - HIGH IP3 - SMT HMC483MS8G / 483MS8GE v01.0710 HIGH IP3 GaAs MMIC MIXER with INTEGRATED LO AMPLIFIER, 0.7 - 1.5 GHz Input IP3 vs. LO Drive 40 Input IP3 vs. Temperature 40 INPUT IP3 (dBm) 30 INPUT IP3 (dBm) 10 MIXERS - HIGH IP3 - SMT 35 35 30 LO =-6dBm LO =-4dBm LO =-2dBm LO = 0dBm LO =+2dBm LO =+4dBm 25 + 25C + 85C - 40C 25 20 0.6 0.7 0.8 0.9 1 1.1 1.2 FREQUENCY (GHz) 1.3 1.4 1.5 20 0.6 0.7 0.8 0.9 1 1.1 1.2 FREQUENCY (GHz) 1.3 1.4 1.5 Input IP2 vs. Temperature 40 Input IP2 vs. LO Drive 40 INPUT IP2 (dBm) 35 35 INPUT IP2 (dBm) 30 30 LO =-6dBm LO =-4dBm LO =-2dBm LO = 0dBm LO =+2dBm LO =+4dBm 25 + 25C + 85C - 40C 25 20 0.6 0.7 0.8 0.9 1 1.1 1.2 FREQUENCY (GHz) 1.3 1.4 1.5 20 0.6 0.7 0.8 0.9 1 1.1 1.2 FREQUENCY (GHz) 1.3 1.4 1.5 Input P1dB vs. Temperature 30 Upconverter IP3 vs. LO Drive 40 INPUT P1dB (dBm) 25 30 INPUT IP3 (dBm) 20 20 15 + 25C + 85C - 40C 10 LO =-6dBm LO =-4dBm LO =-2dBm LO = 0dBm LO =+2dBm LO =+4dBm 10 0.6 0.7 0.8 0.9 1 1.1 1.2 FREQUENCY (GHz) 1.3 1.4 1.5 0 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5 RF FREQUENCY (GHz) 10 - 232 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC483MS8G / 483MS8GE v01.0710 HIGH IP3 GaAs MMIC MIXER with INTEGRATED LO AMPLIFIER, 0.7 - 1.5 GHz MxN Spurious Outputs nLO mRF 0 1 2 3 4 0 xx 4 66 83 106 1 -9 0 71 95 105 2 24 30 50 103 103 3 3 15 61 89 108 4 16 28 61 95 108 LO Freq GHz 0.7 0.8 0.9 1 1.1 1.2 1 21 15 12 9 6 3 Harmonics of LO nLO Spur at RF Port 2 23 23 26 22 22 21 3 24 18 23 33 42 25 4 25 43 39 32 10 MIXERS - HIGH IP3 - SMT 10 - 233 27 26 RF Freq = 0.87 GHz @ -10 dBm LO Freq = 0.8 GHz @ 0 dBm All values in dBc Relative to the IF power level. LO power = 0 dBm All values in dBc below input LO level measured at RF port. Absolute Maximum Ratings RF/IF Input LO Drive Bias Supply (Vdd) Channel Temperature Continuous Pdiss (T = 85°C) (Derate 8.95 mW/°C above 85°C) Thermal Resistance (RTH) (Channel to ground paddle) Storage Temperature Operating Temperature IF DC Current ESD Sensitivity (HBM) +27 dBm +10 dBm +7 Vdc 150 °C 0.58 W 111.7 °C/W -65 to +150 °C -40 to +85 °C ±40 mA Class 1B ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 5. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC483MS8G / 483MS8GE v01.0710 HIGH IP3 GaAs MMIC MIXER with INTEGRATED LO AMPLIFIER, 0.7 - 1.5 GHz Package Information Part Number HMC483MS8G Package Body Material Low Stress Injection Molded Plastic RoHS-compliant Low Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Sn MSL Rating MSL1 MSL1 [1] Package Marking [3] H483 XXXX H483 XXXX 10 MIXERS - HIGH IP3 - SMT HMC483MS8GE [2] [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX Pin Descriptions Pin Number Function Description Interface Schematic 1 LO This pin is AC coupled and matched to 50 Ohms. 2 N/C Not connected. This pin may be connected to RF/DC ground without affecting performance. This pin and the ground paddle must be connected to RF ground. 3, 6, 7 GND 4 Vdd Power supply for LO amplifier. An external RF bypass capacitor is required. 5 IF This pin is DC coupled. For applications not requiring operation to DC this port should be DC blocked externally using a series capacitor. Choose value of capacitor to pass IF frequency desired. For operation to DC, this pin must not sink/source more than 40 mA of current or failure may result. 8 RF This pin is DC coupled and matched to 50 Ohms. 10 - 234 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC483MS8G / 483MS8GE v01.0710 HIGH IP3 GaAs MMIC MIXER with INTEGRATED LO AMPLIFIER, 0.7 - 1.5 GHz Evaluation PCB 10 MIXERS - HIGH IP3 - SMT List of Materials for Evaluation PCB 105188 [1] Item J1 - J3 J4 - J5 C1 U1 PCB [2] Description PCB Mount SMA RF Connector DC Pin 10,000 pF Chip Capacitor, 0603 Pkg. HMC483MS8G / HMC483MS8GE Mixer 104813 Evaluation Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 10 - 235