HMC665LP4E

HMC665LP4 / 665LP4E v00.0508 GaAs MMIC MIXER w/ INTEGRATED IF & LO AMPLIFIER, 0.7 - 1.2 GHz Features High input iP3: +23 dBm Low input LO Drive: -3 to +6 dBm High LO to rF isolation: 36 dB High Conversion Gain: 10 dB ideal for Upconversion or Downconversion 24 Lead 4x4mm sMT Package: 16mm2 Typical Applications The HMC665LP4 / HMC665LP4e is ideal for: • Cellular/3G & WiMAx/LTe/4G infrastructure • Base stations & repeaters • Broadband & Fixed Wireless • Access Points 10 Mixers - HiGH iP3 - sMT • Test & Measurement equipment Functional Diagram General Description The HMC665LP4e is a highly integrated converter iC that operates from 0.7 to 1.2 GHz for both up-conversion and downconversion applications. The HMC665LP4e incorporates a high dynamic range, passive doublebalanced mixer core with integrated LO and iF amplifiers, making it ideal for compact transceiver applications in GsM, WCDMA, TD-sCDMA, WiBro and WiMAx. This versatile converter rFiC operates with a low LO input power level of only -3 dBm, provides up to 10 dB conversion gain, and exhibits +23 dBm input iP3 in downconversion mode. This rFiC provides up to 11 dB conversion gain in upconverter mode. specific evaluation boards are available for both upconverter and downconverter modes. Electrical Specifications, TA = +25° C, LO = 0 dBm, VccLO= VddIF = +5V Parameter Frequency range, rF, LO Frequency range, iF Conversion Gain Noise Figure (ssB) LO to rF isolation LO to iF isolation iP3 (input) 1 dB Compression (input) LO Drive input Level (Typical) supply Current (iddiF + iccLO) 32 7 Min. Typ. 0.7 - 1.2 250 - 450 10 10 36 1 23 10 -3 to +6 150 200 Max. Units GHz MHz dB dB dB dB dBm dBm dBm mA *Unless otherwise noted, all measurements performed as a downconverter and configured as shown in the downconverter mode application circuit, IF=250 MHz 10 - 1 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC665LP4 / 665LP4E v00.0508 GaAs MMIC MIXER w/ INTEGRATED IF & LO AMPLIFIER, 0.7 - 1.2 GHz Downconversion Plots Conversion Gain vs. LO Drive, IF = 250 MHz 15 10 5 0 -5 -10 -15 500 Conversion Gain vs. LO Drive, IF = 450 MHz 15 10 5 0 -5 -10 -15 500 LO= -3 dBm LO= 0 dBm LO= 3 dBm LO= 6 dBm CONVERSION GAIN (dB) 700 900 1100 1300 1500 700 900 1100 1300 1500 FREQUENCY (MHz) FREQUENCY (MHz) Conversion Gain vs. Temperature, IF = 250 MHz 20 15 CONVERSION GAIN (dB) Conversion Gain vs. Temperature, IF = 450 MHz 20 15 CONVERSION GAIN (dB) 10 5 0 -5 -10 -15 -20 500 +25C +85C -40C 10 5 0 -5 -10 -15 -20 500 +25C +85C -40C 700 900 1100 1300 1500 700 900 1100 1300 1500 FREQUENCY (MHz) FREQUENCY (MHz) Input IP2 vs. LO Drive, IF = 450 MHz 90 80 70 IP2 (dBm) 60 50 40 30 500 Input IP2 vs. Temperature, IF = 450 MHz 90 80 70 60 50 40 30 500 +25C +85C -40C -3 dBm 0 dBm +3 dBm +6 dBm IP2 (dBm) 700 900 RF FREQUENCY (MHz) 1100 1300 700 900 RF FREQUENCY (MHz) 1100 1300 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 10 - 2 Mixers - HiGH iP3 - sMT LO= -3 dBm LO= 0 dBm LO= 3 dBm LO= 6 dBm CONVERSION GAIN (dB) 10 HMC665LP4 / 665LP4E v00.0508 GaAs MMIC MIXER w/ INTEGRATED IF & LO AMPLIFIER, 0.7 - 1.2 GHz Downconversion Plots Input IP3 vs. LO Drive, IF = 450 MHz 30 25 Input IP3 vs. Temperature, IF = 450 MHz 30 25 20 15 10 5 0 500 +25C +85C -40C IP3 (dBm) 15 10 5 0 500 -3 dBm 0 dBm +3 dBm +6 dBm Mixers - HiGH iP3 - sMT IP3 (dBm) 10 20 700 900 RF FREQUENCY (MHz) 1100 1300 700 900 RF FREQUENCY (MHz) 1100 1300 Input P1dB vs. Temperature, IF = 350 MHz 16 Isolation vs. Frequency 10 13 ISOLATION (dB) P1dB (dBm) 0 -10 RF to IF LO to RF LO to IF 10 -20 7 +25C +85C -40C -30 4 500 700 900 RF FREQUENCY (MHz) 1100 1300 -40 500 700 900 1100 1300 1500 1700 FREQUENCY (MHz) Upconversion Plots Conversion Gain vs. LO Drive, IF = 250 MHz 15 10 5 0 -5 -10 -15 650 LO= -3 dBm LO= 0 dBm LO= 3 dBm LO= 6 dBm Conversion Gain vs. LO Drive, IF = 450 MHz 15 10 5 0 -5 -10 -15 650 LO= -3 dBm LO= 0 dBm LO= 3 dBm LO= 6 dBm CONVERSION GAIN (dB) CONVERSION GAIN (dB) 825 1000 FREQUENCY (MHz) 1175 1350 825 1000 FREQUENCY (MHz) 1175 1350 10 - 3 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC665LP4 / 665LP4E v00.0508 GaAs MMIC MIXER w/ INTEGRATED IF & LO AMPLIFIER, 0.7 - 1.2 GHz Input IP3 vs. LO Drive, IF = 450 MHz 20 15 10 IP3 (dBm) 5 0 -5 -10 -15 650 -3 dBm 0 dBm +3 dBm +6 dBm Input IP2 vs. LO Drive, IF = 450 MHz 90 80 70 60 50 40 30 650 IP2 (dBm) 10 800 950 RF FREQUENCY (MHz) 1100 1250 800 950 RF FREQUENCY (MHz) 1100 1250 IF Bandwidth 10 5 Return Loss 0 -5 RETURN LOSS (dB) -10 -15 -20 -25 -30 RF LO 0 RESPONSE (dB) -5 -10 -15 -20 -25 -30 -35 200 300 400 IF FREQUENCY (MHz) 500 600 Conversion Gain Return Loss 0 0.5 1 1.5 2 2.5 3 FREQUENCY (MHz) MxN Spurious @ IF Port nLO mrF 0 1 2 3 4 0 xx 7 66 91 91 1 3 0 56 84 91 2 21 33 50 73 91 3 29 52 65 77 91 4 58 59 84 91 91 Harmonics of LO nLO spur at rF Port LO Freq. (GHz) 0.5 0.6 0.7 0.8 0.9 1.0 1.2 1.4 +22 dBm +10 dBm +15 dBm +7 Vdc +8 Vdc 150 °C 0.97 W 67.2 °C/W -65 to +150°C -40 to +85°C 1.6 1 31 28 30 37 38 35 34 35 36 2 32 23 21 21 23 24 27 32 38 3 32 32 30 32 37 40 33 33 46 4 39 47 44 47 53 43 55 58 62.6 All values in dBc below iF power level (1rF - 1LO) Absolute Maximum Ratings rF / Mix iF input (VddiF = +5V) LO input (VccLO = +5V) iFiN VccLO VddiF Junction Temperature Continuous Pdiss (T = 85°C) (derate 14.9 mW/°C above 85°C) Thermal resistance (junction to ground paddle) storage Temperature Operating Temperature LO = 0 dBm Values in dBc below input LO level measured at rF port. Typical Supply Current VddiF + VccLO +4.5 +5.0 +5.5 iddiF + iccLO 130 mA 150 mA 165 mA F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 10 - 4 Mixers - HiGH iP3 - sMT LO = -3 dBm LO = 0 dBm LO = 3 dBm LO = 6 dBm HMC665LP4 / 665LP4E v00.0508 GaAs MMIC MIXER w/ INTEGRATED IF & LO AMPLIFIER, 0.7 - 1.2 GHz Typical Performance Cascade Analysis HMC665LP4E Downconverter Mode (RF Input = 700 to 1200 MHz, IF Output = 250 to 450 MHz, LO = Low Side or High Side) Component Level Description Gain (dB) -8.0 18.0 NF (dB) 8.5 1.0 OiP3 (dBm) 15.0 37.5 OP1dB (dBm) 7.0 21.0 +5V Current (mA) 57.0 93.0 150.0 Gain (dB) -8.0 10.0 10.0 NF (dB) 8.5 9.4 9.4 OiP3 (dBm) 15.0 31.7 31.7 iiP3 (dBm) 23.0 21.7 21.7 Cumulative MCM Performance OP1dB (dBm) 7.0 19.5 19.5 iP1dB (dBm) 16.0 10.5 10.5 10 Mixers - HiGH iP3 - sMT Mixer w/ LO Amplifier iF Amplifier HMC665LP4e Cumulative MCM Performance * rF image rejection filter is not included in the released eval boards. Typical Performance Cascade Analysis HMC665LP4E Upconverter Mode Component Level Description iF Amplifier Mixer w/ LO Amplifier HMC665LP4e Gain (dB) 18.0 -7.5 NF (dB) 1.0 8.5 OiP3 (dBm) 38 21 OP1dB (dBm) 21.0 7.0 +5V Current (mA) 93.0 57.0 150.0 Gain (dB) 18.0 10.0 10.0 (RF Output = 700 to 1200 MHz, IF Input = 250 to 450 MHz, LO = Low Side or High Side) Cumulative MCM Performance NF (dB) 1.0 1.3 1.3 OiP3 (dBm) 38 20.5 20.5 iiP3 (dBm) 20 10 10 OP1dB (dBm) 21.0 7.0 7.0 iP1dB (dBm) 4.0 -3.0 -3.0 Cumulative MCM Performance * iF image rejection filter is not included in the released eval boards. Outline Drawing eLeCTrOsTATiC seNsiTiVe DeViCe OBserVe HANDLiNG PreCAUTiONs NOTes: 1. LeADFrAMe MATeriAL: COPPer ALLOY 2. DiMeNsiONs Are iN iNCHes [MiLLiMeTers] 3. LeAD sPACiNG TOLerANCe is NON-CUMULATiVe. 4. PAD BUrr LeNGTH sHALL Be 0.15mm MAxiMUM. PAD BUrr HeiGHT sHALL Be 0.05mm MAxiMUM. 5. PACKAGe WArP sHALL NOT exCeeD 0.05mm. 6. ALL GrOUND LeADs AND GrOUND PADDLe MUsT Be sOLDereD TO PCB rF GrOUND. 7. reFer TO HiTTiTe APPLiCATiON NOTe FOr sUGGesTeD LAND PATTerN. 10 - 5 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC665LP4 / 665LP4E v00.0508 GaAs MMIC MIXER w/ INTEGRATED IF & LO AMPLIFIER, 0.7 - 1.2 GHz Package Information Part Number HMC665LP4 HMC665LP4e Package Body Material Low stress injection Molded Plastic roHs-compliant Low stress injection Molded Plastic Lead Finish sn/Pb solder 100% matte sn MsL rating MsL1 MsL1 [1] Package Marking [3] H665 xxxx H665 xxxx [2] [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number xxxx 10 Mixers - HiGH iP3 - sMT 10 - 6 Pin Descriptions Pin Number 1, 2, 4, 5, 6, 8, 11, 14, 15, 19, 20, 22 - 24 Function N/C Description No connection. These pins may be connected to rF ground. Performance will not be affected. interface schematic 3 rF This pin is DC coupled and matched to 50 Ohms. 7 iFiN This pin is matched to 50 Ohms with a 56nH inductor to ground. see Application Circuit. 9 CAP AC ground. An external capacitor of 0.01 µF to ground is required for low frequency bypassing. see application circuit for further details. 10 MixiF This pin is DC coupled. For applications not requiring operation to DC, this port should be DC blocked externally using a series capacitor whose value has been chosen to pass the necessary iF frequency range. For operation to DC, this pin must not source/sink more than 18 mA of current or part non-function and possible part failure will result. This pin is AC coupled and matched to 50 Ohms. 12 iFOUT 13 VddiF Power supply for iF amplifier. Choke inductor and bypass capacitor are required. see application circuit. 16 MixLO This pin is DC coupled and matched to 50 Ohms. An off chip DC blocking capacitor is required. 17 GND Backside of package has exposed metal ground paddle that must also be connected to ground. 18 VccLO Power supply and rF Output of the LO amplifier. Three external bypass capacitors are recommended for optimum performance, as illustrated in the application circuit. F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC665LP4 / 665LP4E v00.0508 GaAs MMIC MIXER w/ INTEGRATED IF & LO AMPLIFIER, 0.7 - 1.2 GHz Pin Descriptions Pin Number (Continued) Description interface schematic Function 10 Mixers - HiGH iP3 - sMT 21 LO This pin is DC coupled and matched to 50 Ohms. An off chip DC blocking capacitor is required. see application circuit. Evaluation PCB - Upconverter Mode List of Materials for Evaluation PCB 122009 [1] item J1 - J3 J4 C1, C2, C3 C4, C6 C5, C7 C8 L1, L2 L3 r1, r3, r4 r5 U1 PCB [2] Description PCB Mount sMA rF Connector 2mm DC Header 100 pF Chip Capacitor, 0402 Pkg. 1000 pF Chip Capacitor, 0603 Pkg. 2.2 µF Capacitor, Tantalum 0.01 µF Chip Capacitor, 0402 Pkg. 56 nH Chip inductor, 0402 Pkg. 36 nH Chip inductor, 0603 Pkg. 0 Ohm resistor, 0402 Pkg. 24 Ohm resistor, 1210 Pkg. HMC665LP4(e) - Mixer 119242 evaluation Board The circuit board used in the application should use rF circuit design techniques. signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Arlon 25Fr 10 - 7 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC665LP4 / 665LP4E v00.0508 GaAs MMIC MIXER w/ INTEGRATED IF & LO AMPLIFIER, 0.7 - 1.2 GHz Evaluation PCB - Downconverter Mode 10 Mixers - HiGH iP3 - sMT List of Materials for Evaluation PCB 122010 [1] item J1 - J3 J4 C1, C2, C3 C4, C6 C5, C7 C8 L1, L2 L3 r2, r3, r4 r5 U1 PCB [2] Description PCB Mount sMA rF Connector 2mm DC Header 100 pF Chip Capacitor, 0402 Pkg. 1000 pF Chip Capacitor, 0603 Pkg. 2.2 µF Capacitor, Tantalum 0.01 µF Chip Capacitor, 0402 Pkg. 56 nH Chip inductor, 0402 Pkg. 36 nH Chip inductor, 0603 Pkg. 0 Ohm resistor, 0402 Pkg. 24 Ohm resistor, 1210 Pkg. HMC665LP4(e) - Mixer 119242 evaluation Board The circuit board used in the application should use rF circuit design techniques. signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Arlon 25Fr F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 10 - 8 HMC665LP4 / 665LP4E v00.0508 GaAs MMIC MIXER w/ INTEGRATED IF & LO AMPLIFIER, 0.7 - 1.2 GHz Application Circuit - Upconverter Mode 10 Mixers - HiGH iP3 - sMT 10 - 9 F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com HMC665LP4 / 665LP4E v00.0508 GaAs MMIC MIXER w/ INTEGRATED IF & LO AMPLIFIER, 0.7 - 1.2 GHz Application Circuit - Downconverter Mode 10 Mixers - HiGH iP3 - sMT F or price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or apps@hittite.com 10 - 10