HI-8588

HI-8588 August 2006 ARINC 429 LINE RECEIVER PIN CONFIGURATION VCC - 1 TESTA - 2 RINB - 3 RINA - 4 8 - TESTB DESCRIPTION The HI-8588 is an ARINC 429 bus interface receiver and is available in a SO 8 pin package. The technology is analog/digital CMOS. The circuitry requires only a 5 volt supply. The ARINC bus can be connected directly to the chip. The typical 10 volt differential signal is translated and input to a window comparator and latch. The comparator levels are just below the standard 6.5 volt minimum ARINC data threshold and just above the standard 2.5 volt maximum ARINC null threshold. The TESTA and TESTB inputs bypass the analog for testing purposes. Also if TESTA and TESTB are both taken high, the analog powers down and the digital outputs tristate allowing wire-or possibilities. Please refer to the HI-8588-10 for applications where an external resistance in series with the ARINC inputs is required for lightning protection or when the digital outputs need to be a logic zero rather than open circuit when TESTA and TESTB are both high. See Holt Application Note AN-300 for more information on lightning protection. 8588PS 7 - ROUTB 6 - ROUTA 5 - GND 8 - PIN PLASTIC NARROW BODY SOIC SUPPLY VOLTAGES vcc = 5.0V ± 5% FUNCTION TABLE RECEIVER RINA -1.25V to 1.25V -3.25V to -6.5V RINB -1.25V to 1.25V 3.25V to 6.5V -3.25V to -6.5V X X X TESTA 0 0 0 0 1 1 TESTB 0 0 0 1 0 1 ROUTA ROUTB 0 0 1 0 1 HI-Z 0 1 0 1 0 HI-Z FEATURES 3.25V to 6.5V X ! ! ! ! ! Direct ARINC 429 line receiver interface in a small outline package Receiver input hystersis at least 2 volts Test inputs that bypass analog input and can power down and tri-state outputs Plastic and ceramic package options surface mount and DIP Mil processing available X X PIN DESCRIPTION TABLE PIN 1 2 3 4 5 6 7 8 SYMBOL VCC TESTA RINB RINA GND ROUTA ROUTB TESTB FUNCTION SUPPLY LOGIC INPUT ARINC INPUT ARINC INPUT POWER LOGIC OUTPUT LOGIC OUTPUT LOGIC INPUT CMOS RECEIVER B INPUT RECEIVER A INPUT GROUND RECEIVER CMOS OUTPUT A RECEIVER CMOS OUTPUT B CMOS DESCRIPTION 5 VOLT SUPPLY (DS8588 Rev. C) HOLT INTEGRATED CIRCUITS www.holtic.com 08/06 HI-8588 FUNCTIONAL DESCRIPTION RECEIVER Figure 1 shows the general architecture of the ARINC 429 receiver. The receiver operates off the VCC supply only. The inputs RINA and RINB each have series resistors, typically 35K ohms. They connect to level translators whose resistance to Ground is typically 10K ohms. Therefore, any series resistance added to the inputs will affect the voltage translation. After level translation, the inputs are buffered and become inputs to a differential amplifier. The amplitude of the differential signal is compared to levels derived from a divider between VCC and Ground. The nominal settings correspond to a One/Zero amplitude of 6.0V and a Null amplitude of 3.3V. The status of the ARINC receiver input is latched. A Null input resets the latches and a One or Zero input sets the latches. The logic at the output is controlled by the test signal which is generated by the logical OR of the TESTA and TESTB pins. If TESTA and TESTB are both One, then the receiver is powered down and the output pins float. The powerdown does not disconnect the internal resistors at the ARINC input. ONE S Q LATCH R TEST ROUTA TEST TESTA TESTA ' TESTB RINA RINB ESD PROTECTION AND TRANSLATION NULL TEST ZERO S Q LATCH R ROUTB TEST TESTB TESTA ' TESTB NULL FIGURE 1 - RECEIVER BLOCK DIAGRAM 5V 1 HARDWIRE OR DRIVE FROM LOGIC { 2 8 4 VCC TESTA TESTB ROUTA ROUTB 6 7 RXD1 RXD0 HI-8588 RINA RINB APPLICATION INFORMATION Figure 2 shows a possible application of the HI-8588 interfacing an ARINC receive channel to the HI-6010 which in turn interfaces to an 8-bit bus. ARINC Channel 3 HI-6010 5 15V 1 6 SLP1.5 TXAOUT V+ TX1IN 8 BIT BUS 8 3 2 TXD1 ARINC Channel 7 HI-8586 TXBOUT GND VTX0IN TXD0 4 5 -15V FIGURE 2 - APPLICATION DIAGRAM HOLT INTEGRATED CIRCUITS 2 HI-8588 ABSOLUTE MAXIMUM RATINGS Voltages referenced to Ground Supply voltages VCC...................................................7V ARINC input - pins 3 & 4 Voltage at either pin......+29V to -29V DC current per input pin................ ±10mA Power dissipation at 25°C plastic DIP............0.7W ceramic DIP..........0.5W Solder Temperature ........275°C for 10 sec Storage Temperature........-65°C to +150°C NOTE: Stresses above absolute maximum ratings or outside recommended operating conditions may cause permanent damage to the device. These are stress ratings only. Operation at the limits is not recommended. Supply Voltages VCC...........................................5V ± 5% Temperature Range Industrial Screening........-40°C to +85°C Hi-Temp Screening.......-55°C to +125°C Military Screening.........-55°C to +125°C RECOMMENDED OPERATING CONDITIONS DC ELECTRICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE, VCC = 5.0V UNLESS OTHERWISE STATED PARAMETERS ARINC input voltage one or zero null common mode logic input voltage high low ARINC input resistance RINA to RINB RINA or RINB to Gnd or VCC logic input current source sink logic output drive current one zero Current drain operating powerdown SYMBOL V DIN VNIN VCOM V IH V IL R DIFF R SUP I IH I IL I OH I OL I CC1 I CC2 supplies floating " " TEST CONDITIONS differential voltage, pins 3 & 4 " " " with respect to Ground MIN 6.5 TYP 10 MAX 13 2.5 5.0 UNITS volts volts volts 3.5 - - 1.5 volts volts 30 19 75 40 - Kohm Kohm V IN = 0 V V IN = 5 V V = 4.6V OH V = 0.4V OL pins 2, 8 = 0V; pins 3, 4 open pins 2, 8 = 5V; pins 3, 4 open - - 0.1 0.1 µA µA 3.6 -1.6 5.6 -0.8 - mA mA - 2.3 0.36 6.3 0.6 mA mA HOLT INTEGRATED CIRCUITS 3 HI-8588 AC ELECTRICAL CHARACTERISTICS OPERATING TEMPERATURE RANGE, VCC = 5.0V UNLESS OTHERWISE STATED PARAMETERS Receiver propagation delay Output high to low Output low to high Receiver output transition times Output high to low Output low to high Input capacitance (1) ARINC differential ARINC single ended to Ground Logic Notes: 1. Guaranteed but not tested SYMBOL TEST CONDITIONS defined in Figure 3, C L= 50pF t phlr t plhr t fr t rr CAD CAS C IN MIN TYP MAX UNITS - 600 600 - ns ns - 50 50 5 - 80 80 10 10 10 ns ns pF pF pF VDIFF pin 4 - pin 3 t plhr t phlr 90% 10V 0V -10V t rr pin 6 t plhr 10% 5V 0V t fr t phlr pin 7 FIGURE 3 - RECEIVER TIMING 5V 0V ORDERING INFORMATION HI - 8588 xx x x PART NUMBER LEAD FINISH Blank F PART NUMBER Tin / Lead (Sn / Pb) Solder 100% Matte Tin (Pb-free, RoHS compliant) TEMPERATURE RANGE FLOW BURN IN I T M PART NUMBER -40°C TO +85°C -55°C TO +125°C -55°C TO +125°C PACKAGE DESCRIPTION I T M NO NO YES PD PS CR 8 PIN PLASTIC DIP (not available with “M” flow) 8 PIN PLASTIC NARROW BODY SOIC 8 PIN CERDIP (not available Pb-free) HOLT INTEGRATED CIRCUITS 4 HI-8588 PACKAGE DIMENSIONS inches (millimeters) 8-PIN PLASTIC DIP Package Type: 8P .385 ± .015 (4.699 ± .381) .250 ± .010 (6.350 ± .254) .100 ± .010 (3.540 ± .254) .300 ± .010 (7.620 ± .254) 7° TYP. .135 ± .015 (3.429 ± .381) .1375 ± .0125 (3.493 ± .318) .019 ± .002 (.483 ± .102) .025 ± .010 (.635 ± .254) .0115 ± .0035 (.292 ± .089) .055 ± .010 (1.397 ± .254) .335 ± .035 (8.509 ± .889) 8-PIN PLASTIC SMALL OUTLINE (SOIC) - NB (Narrow Body) .1935 ± .0035 (4.915 ± .085) Package Type: 8HN .0086 ± .0012 (.2184 ± .0305) .236 ± .008 (5.994 ± .203) PIN 1 .1535 ± .0035 (3.90 ± .09) .0165 ± .0035 (.4191 ± .0889) Detail A .055 ± .005 (1.397 ± .127) 0° to 8 ° .050 ± .010 (1.27 ± .254) .033 ± .017 (.8382 ± .4318) .0069 ± .0029 (.1753 ± .0737) Detail A HOLT INTEGRATED CIRCUITS 5 HI-8588 PACKAGE DIMENSIONS inches (millimeters) 8-PIN CERDIP Package Type: 8D .380 ± .004 (9.652 ± .102) .005 MIN. (.127 MIN.) .248 ± .003 (6.299 ± .076) .039 ± .006 (.991 ± .154) .100 ± .008 (2.540 ± .203) .015 MIN. (.381 MIN.) .314 ± .003 (7.976 ± .076) .200 MAX. (5.080 MAX.) .163 ± .037 (4.140 ± .940) Base Plane Seating Plane .056 ± .006 (1.422 ± .152) .018 ± .006 (.457 ± .152) .350 ± .030 (8.890 ± .762) .010 ± .006 (.254 ± .152`) HOLT INTEGRATED CIRCUITS 6