HRF-SW1001

HRF-SW1001 SPDT Absorptive RF Switch Features • • • • • • • • High Isolation Of > 40 dB @ 2 GHz Low Insertion Loss Of 1.1dB @ 2 GHz DC To 4GHz Operating Frequency Integrated CMOS Control Logic Integrated ESD Protection on Digital I/O Single Positive Supply Voltage TM Ultra Small LPCC Packaging Impedance matched for 75 Ohm systems Product Description The Honeywell HRF-SW1001 is a high performance single pole double throw (SPDT) absorptive RF switch that is ideal for use in wireless basestation and handset applications that require minimum power and minimum insertion loss. The HRF-SW1001 is manufactured with Honeywell's patented Silicon On Insulator (SOI) CMOS technology, which provides the performance of GaAs with the economy and integration capabilities of conventional CMOS technology. HRF-SW1001 in LPCCTM Package RF Electrical Specifications @ + 25oC Results @ Vdd=5.0 =/- 10%, Vss = 0 unless otherwise stated, Z0=75 ohms Parameter T est Condition Frequency Minimum Insertion Loss DC – 0.5 GHz 2.0 GHz 3.0 GHz DC – 0.5 GHz 2.0 GHz 3.0 GHz DC – 0.5 GHz 2.0 GHz 3.0 GHz Input Power Vss=Gnd Vss= -3 Two-Tone Inputs Up To + 5 dBm Vss=Gnd Vss= -3 10% To 90% 50% Cntl To 90%/10%Rf In-Band 1.0 GHz 1.0 GHz 2.0 GHz 2.0 GHz 21 29 35 35 10 20 10 dBm dBm dBm dBm nS nS mV T ypical 0.9 1.1 1.4 53.5 42.5 39.0 1.1:1 1.2:1 1.2:1 Maximum 1.5 1.7 1.9 Units dB dB dB dB dB dB Ratio Ratio Ratio Isolation 50 40 35 VSWR* 1.3:1 1dB Compression Input IP3 Trise, Tfall* Ton, Toff Transients *By design _ _______________________________________________________________________________________________________ Web Site: Email: 2002 1001W www.mysoiservices.com mysoiservices@honeywell.com Published June 2002 Page 1 Honeywell Solid State Electronics Center 12001 State Highway 55 Plymouth, Minnesota 55441-4799 1-800-323-8295 HRF-SW1001 DC Electrical Specifications @ + 25oC Parameter Single VDD Supply Voltage CMOS Logic Level (0) CMOS Logic Level (1) Input Leakage Current * Performance curves are for Vdd = +5.0 +/- 10% Minimum 3.3* 0 VDD – 0.8 T ypical 5.0 Maximum 5.5 0.8 VDD 10 Units V V V uA Absolute Maximum Ratings1 Parameter VDD Vin Digital Logic 0 Vin Digital Logic 1 Maximum Input Power ESD Voltage Operating Temperature Range Storage Temperature Range Absolute Maximum +6.0 Vss - 0.6 Vdd + 0.6 > 35 400 +85 +125 Units V V V dBm V Degrees C Degrees C (Note 1) Operation beyond any of these parameters may cause permanent damage. Latch-Up: Unlike conventional CMOS RF switches, Honeywell's HRF-SW1001 is immune to latch-up. ESD Protection: Although this device contains ESD protection circuitry on all digital inputs, conventional precautions should be taken to ensure that the Absolute Maximum Ratings are not exceeded. Package Outline Drawing 3 mm Bottom View, 12 Pin 3X3 mm LPCCTM Package ASAT LPCC Marketing Outline Dwg. # GMJ00004 For more information see http://www.asat.com 3 mm _ _______________________________________________________________________________________________________ Web Site: Email: 2002 1001W www.mysoiservices.com mysoiservices@honeywell.com Published June 2002 Page 2 Honeywell Solid State Electronics Center 12001 State Highway 55 Plymouth, Minnesota 55441-4799 1-800-323-8295 HRF-SW1001 Truth Table Switch Control 0 1 "0" = CMOS Low, "1” = CMOS High RF Output 1 RF INPUT --- RF Output 2 --RF INPUT Pin Configuration Pin 1 2 3 4 5 6 Function GROUND RF OUT 2 GROUND VDD SWITCH CONTROL VSS Pin 7 8 9 10 11 12 Function GROUND RF OUT 1 GROUND GROUND RF IN GROUND Evaluation Circuit Board Connections RF RF HRFEvaluation Top RF Honeywell HRF-SW1000 VSS VDD Ground Open SW Control _ _______________________________________________________________________________________________________ Web Site: Email: 2002 1001W www.mysoiservices.com mysoiservices@honeywell.com Published June 2002 Page 3 Honeywell Solid State Electronics Center 12001 State Highway 55 Plymouth, Minnesota 55441-4799 1-800-323-8295 HRF-SW1001 Performance Curves Insertion Loss Insertion Loss versus Frequency 0 -1 Insertion Loss (dB) -2 -3 -4 -5 -6 -7 -8 -9 -10 0 1 2 3 4 The Insertion Loss curve shows the worst case loss versus frequency at Vdd = +5.0 +/10%, Ta = 25C, Z0 = 75 Ohms Frequency Isolation Isolation versus Frequency -20.00 -30.00 -40.00 -50.00 The Isolation curve shows the typical isolation of an “off” state output to the insertion path. (dB) -60.00 -70.00 -80.00 -90.00 -100.00 0 0.5 1 1.5 2 2.5 3 Frequency (GHz) _ _______________________________________________________________________________________________________ Web Site: Email: 2002 1001W www.mysoiservices.com mysoiservices@honeywell.com Published June 2002 Page 4 Honeywell Solid State Electronics Center 12001 State Highway 55 Plymouth, Minnesota 55441-4799 1-800-323-8295 HRF-SW1001 Return Loss Input / Output Return Losses versus Frequency 0.00 -5.00 Return Loss (dB) -10.00 -15.00 -20.00 -25.00 -30.00 -35.00 -40.00 -45.00 -50.00 0 0.5 1 1.5 2 2.5 3 The return loss curve shows the input return loss S11, the output return loss in the insertion path S22, and the output return loss in the isolation state S33. Frequency (GHz) Evaluation Circuit Board Honeywell's evaluation board provides an easy to use method of evaluating the RF performance of our switch. Simply connect power, DC and RF signals to be measuring switch performance in less than 10 minutes. HRF-SW1001 Evaluation Board _ _______________________________________________________________________________________________________ Web Site: Email: 2002 1001W www.mysoiservices.com mysoiservices@honeywell.com Published June 2002 Page 5 Honeywell Solid State Electronics Center 12001 State Highway 55 Plymouth, Minnesota 55441-4799 1-800-323-8295 HRF-SW1001 Evaluation Circuit Board Layout Design Details Item PCB Switch Chip Capacitor RF Connector DC Pin Description Impedance Matched Multi-Layer FR4 HRF-SW1001 RF Switch Panasonic Model ECU-E1C103KBQ Capacitor, .01uf 0402 10% 16V Johnson Connectors Model 142-0701-801 SMA RF Coaxial Connector Mil-Max Model 800-10-064-10-001 Header Pins Ordering Information Ordering Number HRF-SW1001-B HRF-SW1001-TR HRF-SW1001-E (Note 2) Contact Honeywell for details Product Delivered In Chip Tubes 2 Delivered On Tape And Reel Engineering Evaluation Board LPCC TM is a registered Trademark of ASAT Ltd. Honeywell reserves the right to make changes to improve reliability, function or design. Honeywell does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others. _ _______________________________________________________________________________________________________ Web Site: Email: 2002 1001W www.mysoiservices.com mysoiservices@honeywell.com Published June 2002 Page 6 Honeywell Solid State Electronics Center 12001 State Highway 55 Plymouth, Minnesota 55441-4799 1-800-323-8295