PPT0001DWW5VB-EF

PPT Precision Pressure Transducer Highly Accurate Over a Wide Temperature Range Honeywell’s Precision Pressure Transducer (PPT) offers extraordinary value with high accuracy over a wide temperature range. The PPT combines proven silicon sensor technology with microprocessor -based signal conditioning to provide an extremely smart pressure transducer. Available in a compact, rugged design, the PPT has many software features that support a wide range of applications. Specifications PERFORMANCE Total Error Band (1) See Ordering Information Temperature Range Operating: -40 to 85ºC Storage: -55 to 90°C POTENTIAL APPLICATIONS 8.33 ms to 51.2 min; minimum response delay 17 ms • Secondary Air Data Resolution Digital: Up to 0.001% FS, Analog: 1.22 mV steps (12 bits) • Altimeters Long Term Stability 0.025%FS per year typical Sample Rate (3) • Engine Testing • Flight Testing MECHANICAL • Meteorology Pressure Units (3) atm, bar, cmwc, ftwc, hPa, inHg, inwc, kg/cm2, KPa, mBar, mmHg, MPa, mwc, psi, user, lcom, pfs Media Compatibility Suitable for non-condensing, non-corrosive, and non-combustible gases Weight Approx. 5 oz. (142 gm) without fittings • Flow and Pressure Calibrators • Instrumentation and Analytical Equipment • Process Control • Research and Development ELECTRICAL Output (3) (4) RS-232 Digital with 0-5V Analog, RS-485 Digital with 0-5V Analog Power Requirements Supply Voltage: 5.5 to 30 VDC, Operating Current: 35 mA maximum Baud Rate (3) User configurable between 1200 and 28800 bits/sec Bus Addressing (3) Address up to 89 units Connector MIL-C-26482, Shell Size #10, 6-pin, #20 size ENVIRONMENTAL Mechanical Shock 1500G, 0.5 ms half sine; per MIL-STD-883D, M2002.3, Cond. B Thermal Shock 24 1-hr cycles, -40 to 85°C Vibration 0.5 in or 20G, 20-2000 Hz; per MIL-STD-883D, M2007.2, Cond. A Overpressure (2) Burst Pressure (2) 3X FS 3X FS EMC Directive Compliant, Metal Connector Model Only RoHS Non-Compliant (1) Total Error is the sum of worst case linearity, repeatability, hysteresis, thermal effects and calibration errors over the operating temperature range. Full scale for differential ranges is the sum of + and – ranges. Calibration is traceable to NIST. (2) Exposure to overpressure will not permanently affect calibration or accuracy of unit. Burst pressure is the sum of the measured pressure plus the static pressure and exceeding it may result in media escape. (3) User configurable. (4) Recommended load impedance of 100 k-ohm or greater. FEATURES & BENEFITS • HIGHLY ACCURATE Accuracy is guaranteed over the whole operating temperature range Simplifies System Design No additional signal compensation needed to gain the benefits of a very accurate sensor • SMART, DIGITAL SENSING AND CONTROL Efficient Data Acquisition Network up to 89 units • VERSATILE AND CONFIGURABLE Works with existing and new systems 0-5V analog and either RS-232 or RS-485 digital output Optimizes Output User-configurable pressure units, sampling, update rate Flags Problems Internal diagnostics set flags, indicates errors • USER SELECTABLE SOFTWARE FEATURES Baud Rate, Parity Setting, Continuous Broadcast, ASCII or Binary Output, Sensor Temperature Output (°C or °F), Deadband, Sensitivity, Tare Value, Configurable Analog Output • ISO-9001, ISO-14001 PPT Specifications Ordering Information Dimensions PPT PRECISION PRESSURE TRANSDUCER PPT Full Scale Pressure Range Absolute Gauge Differential Digital Total Error Band(1)(2) Analog Total Error Band(1)(2) 0001 N/A 1 PSI N/A ±(0.20%FS + 0.04% Abs. Reading) ±(0.24%FS + 0.04% Abs. Reading) 0001 N/A N/A ±1 PSI ±(0.10%FS + 0.04% Abs. Reading) ±(0.12%FS + 0.04% Abs. Reading) 0002 N/A 2 PSI ±2 PSI ±(0.10%FS + 0.04% Abs. Reading) ±(0.12%FS + 0.04% Abs. Reading) 0005 N/A 5 PSI ±5 PSI ±(0.10%FS + 0.04% Abs. Reading) ±(0.12%FS + 0.04% Abs. Reading) 0010 N/A 10 PSI ±10 PSI ±0.10%FS Max. ±0.12%FS Max. 0015 15 PSI N/A N/A ±0.10%FS Max. ±0.12%FS Max. 0020 20 PSI 20 PSI N/A ±0.10%FS Max. ±0.12%FS Max. 0050 50 PSI N/A N/A ±0.10%FS Max. ±0.12%FS Max. P1 PRESSURE P2 PRESSURE A Absolute TYPE 0 (vacuum) to FS N/A G Gage Reference to FS Reference D Differential +FS to –FS rel. to P2 +FS to –FS rel. to P1 P1 PRESSURE CONNECTION (ABSOLUTE, GAUGE, DIFFERENTIAL) F Filter (blocks debris) G Stainless SwagelokTM (1/8 inch female) K Stainless Swagelok-compatible (1/8 inch male) R Brass barbed, right angle (1/8 inch ID tubing) W Brass barbed (1/8 inch ID tubing) X Brass Swagelok® (1/8 inch female) P2 PRESSURE CONNECTION (GAUGE, DIFFERENTIAL) F Filter (blocks debris) G Stainless Swagelok® (1/8 inch female) K Stainless Swagelok-compatible (1/8 inch male) R Brass barbed, right angle (1/8 inch ID tubing) W Brass barbed (1/8 inch ID tubing) X Brass Swagelok® (1/8 inch female) N Not Applicable (Absolute) OUTPUTS 2V RS-232 digital, 0-5V analog 5V RS-485 digital, 0-5V analog ELECTRICAL CONNECTION A Plastic 6-pin connector B Metal 6-pin connector - OPTIONS PPT2 0020 A W N 2V A A Demonstration Kit(2) (RS-232 Only) B Mating Connector C Power Supply/Data Cable (RS-232 only) E Certificate of Conformance F Calibration Certificate -BEF (1) Tighter accuracy available on some models. Consult factory. (2) Demonstration kit includes unit, power supply/data cable (120V), demonstration software, and user manual. OPTION C EOS (electrical overstress) sensitive device Damage may occur when subjected to EOS. Do not exceed specified ratings to avoid performance degradation or loss of functionality. Find out more For more information on Honeywell’s Precision Pressure Transducers visit us online at www.pressuresensing.com. Honeywell reserves the right to make changes to improve reliability, function or design. Honeywell does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others. Customer Service Email: quotes@honeywell.com Honeywell Aerospace 12001 State Highway 55 Plymouth, MN 55441 aerospace.honeywell.com ESD (electrostatic discharge) sensitive device Damage may occur when subjected to high energy ESD. Proper ESD precautions should be taken to avoid performance degradation or loss of functionality. ADS-14179 rev F N61-2080-000-000 | 02/19 © 2019 Honeywell International Inc.