HEDS-9711R-200LPI51

Agilent HEDS-9710, HEDS-9711 200 lpi Analog Output Small Optical Encoder Modules Data Sheet Description The HEDS-9710/HEDS-9711 series is a high performance, low cost, optical incremental encoder module. When operated in conjunction with either a codewheel or codestrip, this module detects rotary or linear position. The encoder module consists of a lensed LED source and a detector IC enclosed in a small C-shaped plastic package. Due to a highly collimated light source and a unique photodetector array, the module is extremely tolerant to mounting misalignment. The two-channel analog outputs and 5 V supply input are accessed through four solder-plated leads located on 2.54 mm (0.1 inch) centers. The standard HEDS-9710/HEDS9711 is designed for use with an appropriate optical radius codewheel, or linear codestrip. Please contact the factory for more information. Applications The HEDS-9710/HEDS-9711 provides sophisticated motion detection at a low cost, making closed-loop control very costeffective. Typical applications include printers, plotters, copiers, and office automation equipment. Note: Agilent Technologies encoders are not recommended for use in safety critical applications, eg., ABS braking systems, power steering, life support systems, and critical care medical equipment. Please contact sales representative if more clarification is needed. Features • Small size • Multiple mounting options • 200 lpi resolution • Linear and rotary options available • Insensitive to radial and axial play • 15°C to 45°C operating temperature • Two-channel analog output • Single 5 V supply • Wave solderable Theory of Operation The HEDS-9710/HEDS-9711 is a C-shaped emitter/detector module. Coupled with a codewheel, it translates rotary motion into a two-channel analog output. Coupled with a codestrip, it translates linear motion into analog outputs. ESD WARNING: NORMAL PRECAUTIONS SHOULD BE TAKEN TO AVOID STATIC DISCHARGE. The module contains a single Light Emitting Diode (LED) as its light source. The light is collimated into a parallel beam by means of a single lens located directly over the LED. Opposite the emitter is the integrated detector circuit. This IC consists of multiple sets of photodetectors and the signal processing circuitry necessary to produce the analog waveforms. The codewheel/codestrip moves between the emitter and detector, causing the light beam to be interrupted by the pattern of spaces and bars on the codewheel/ codestrip. The photodiodes which detect these interruptions are arranged in a pattern that corresponds to the radius and count density of the codewheel/ codestrip. These detectors are also spaced such that a light period on one pair of detectors corresponds to a dark period on the adjacent pair of detectors. The photodiode outputs are fed through the signal processing circuitry, which produces the final outputs for channels A and B. Due to this integrated phasing technique, the analog output of channel A is in quadrature with channel B (90 degrees out of phase). Package Dimensions See HEDS-9700 datasheet for package outline drawings. Definitions Count (N) : The number of bar and window pairs or Counts Per Revolution (CPR) of the codewheel, or the number of Lines Per Inch (LPI) of the codestrip. 1 Shaft Rotation = 360 mechanical degrees = N cycles 1 cycle (c) = 360 electrical degrees (°e) = 1 bar and window pair Pulse Width (P): The number of electrical degrees that an output is high during one cycle. This value is nominally 180°e or 1/2 cycle. Pulse Width Error (∆P): The deviation, in electrical degrees, of the pulse width from its ideal value of 180°e. State Width (S): The number of electrical degrees between a transition in the output of channel A and the neighboring transition in the output of channel B. There are four states per cycle, each nominally 90°e. State Width Error (∆S): The deviation, in electrical degrees, of each state width from its ideal value of 90°e. Phase (Φ ): The number of electrical degrees between the center of the high state of channel A and the center of the high state of channel B. This value is nominally 90°e for quadrature output. Phase Error (∆Φ) : The deviation of the phase from its ideal value of 90°e. Direction of Rotation: When the codewheel rotates counterclockwise, as viewed looking down on the module (so the marking is visible), channel A will lead channel B. If the codewheel rotates in the opposite direction, channel B will lead channel A. Optical Radius (ROP) : The distance from the codewheel’s center of rotation to the optical center (O.C.) of the encoder module. Mounting Position (RM) : Distance from Motor Shaft center of rotation to center of Alignment Tab receiving hole. Absolute Maximum Ratings Parameter Storage Temperature Operating Temperature Supply Voltage Soldering Temperature Symbol TS TA VCC Min. –40 15 –0.5 Max. 85 45 7 260 Units °C °C V °C t ≤ 5 sec. Notes Recommended Operating Conditions Parameter Temperature Supply Voltage Count Frequency 2 Symbol T VCC Min. 15 4.8 Max. 45 5.2 8 V kHz Ripple < 100 mVp-p (Velocity (rpm) x N) 60 Units Notes Waveform Definition ANALOG Iap Ibp A B Ibm Iam DIGITAL A B P P S1 S2 S3 S4 Name Analog Peak Analog Peak-to-Peak Analog Offset State Width Paramenter Definition The absolute value in µA of the magnitude of the analog signal (i.e., one-sided reading). Label Iap, Ibp, Iam, Ibm Iapp Ibpp Ipp Ioffset State Width The peak-to-peak signal magnitude in µA of the analog signal. The offset in µA from the mid-point of the analog peak-to-peak signal to the zero current point. The number of electrical degrees between a transition in channel A and the neighboring transition in channel B. There are four states per cycle, each nominally 90°e. The transitions are determined by where the analog signal crosses the Zero point. The deviation, in electrical degrees, of each state width from its ideal value of 90°e. The number of electrical degrees that an analog output is greater than zero during one cycle. This value is nominally 180° e or 1/2 cycle. State 1 State 2 State 3 State 4 State Width Error Pulse Width State Width Error Pulse Width P Pulse Width Error Pulse Width Error The deviation, in electrical degrees, of each pulse width from its ideal value of 180°e. Electrical Characteristics Electrical Characteristics over Recommended Operating Range, Typical at 25°C. Parameter Supply Current 3 Symbol ICC Min. Typ. 17 Max. 40 Units mA Notes Encoding Characteristics Encoding Characteristics over Recommended Operating Range and Recommended Mounting Tolerances. These characteristics do not include codewheel/codestrip contributions. Units Radial Tangential Gap Temperature O.R. CPR Codewheel Slot/Spoke Ipp Ioffset State Width Error Pulse Width Error microns microns microns °C mm count ratio µA µA e° e° ± 130 ± 130 50 – 250 15 – 45 18 – Linear 900 – Linear 0.9 – 1.1 Min. 10 –4 –40 –40 Max. 73 +4 +40 +40 Recommended Codewheel and Codestrip Characteristics Parameter Window/Bar Ratio Window Length (Rotary) Absolute Maximum Codewheel Radius (Rotary) Center of Post to Inside Edge of Window Center of Post to Outside Edge of Window Center of Post to Inside Edge of Codestrip Symbol Ww/Wb Lw Rc W1 W2 L Min. 0.9 1.80 (0.071) Max. 1.1 2.30 (0.091) Rop + 3.40 (Rop + 0.134) Units Notes mm (inch) mm (inch) mm (inch) mm (inch) Includes eccen– tricity errors 1.04 (0.041) 0.76 (0.030) 3.60 (0.142) mm (inch) 4 Analog Encoder Interface Circuit VREF I+ + – C VA IA-IN R1 VREF I+ + – C VB The circuit shown can be used to convert the current output to a voltage. Resistor value, R1, and Capacitor, C, are specified to attain required gain and low-pass filtering, which are application specific. The gain is chosen to attain maximum output swing and not clamp the op-amp. VREF should be set to 1.4 V ± 0.2 V. A 0.1 µF bypass capacitor (decoupling capacitor) is recommended to be placed within 1 cm of the encoder for optimal power supply noise rejection. Outputs are high impedance (typical 1 M ohm) and susceptible to EMI. IB-IN R1 VREF = 1.4 V ± 0.2 V (DC) Ordering Information HEDS-971 Option Lead Configurations 0 – straight leads 1 – bent leads Resolutions R – 200 lpi Bracket Options 50 51 5 Package Dimensions Option 50 LEAD THICKNESS = 0.25 mm LEAD PITCH = 2.54 mm 3.8 10.8 ± 0.5 CH B R 1.4 5.5 ± 0.3 R 2.6 3.0 OPTION CODE GND VCC 0.5 CH A PIN 1 ID 8.7 1.4 AGILENT XXXXX 50 7.0 12.6 ± 0.5 0.14 (OPTICAL CENTER) 2x ∅ 2.00 ± 0.02 4.2 7.5 10.1 3.9 0.8 1.70 ± 0.15 3.90 ± 0.10 PART # (REFER -05) 8.4 15.0 C YYWW 5.0 4.2 X 6.4 DATE CODE 20.2 ± 0.5 1.8 C = COUNTRY OF ORIGIN MARKING (REFER -05 FOR DETAILS) 9.8 Package Dimensions Option 51 LEAD THICKNESS = 0.25 mm LEAD PITCH = 2.54 mm 3.8 10.8 ± 0.5 CH B GND VCC 0.5 3.0 5.5 ± 0.3 ∅ 2.8 8.7 OPTION CODE CH A PIN 1 ID AGILENT XXXXX 51 7.0 12.6 ± 0.5 0.14 (OPTICAL CENTER) 2x ∅ 2.00 ± 0.02 4.2 7.5 10.1 3.9 0.8 1.70 ± 0.15 3.90 ± 0.10 PART # (REFER -05) 8.4 15.0 C YYWW 4.34 ± 0.20 4.2 X 6.4 DATE CODE 20.2 ± 0.5 1.8 C = COUNTRY OF ORIGIN MARKING (REFER -05 FOR DETAILS) 9.8 Package Dimensions Bent Version – Option 50 LEAD THICKNESS = 0.25 mm LEAD PITCH = 2.54 mm 6.0 3.0 ± 0.3 CH B CH A R 2.6 R 1.4 VCC OPTION CODE GND 5° TYP. PIN 1 ID 8.7 1.4 XXXXX 0.14 (OPTICAL CENTER) 2x ∅ 2.00 ± 0.02 4.2 7.5 10.1 3.9 0.8 1.70 ± 0.15 3.90 ± 0.10 PART # (REFER -05) 8.4 15.0 C YYWW 5.0 4.2 X 6.4 9.2 ± 0.3 AGILENT 50 7.0 12.6 ± 0.5 DATE CODE 20.2 ± 0.5 1.8 C = COUNTRY OF ORIGIN MARKING (REFER -05 FOR DETAILS) 9.8 3.8 0.5 10.8 ± 0.5 Package Dimensions Bent Version – Option 51 LEAD THICKNESS = 0.25 mm LEAD PITCH = 2.54 mm 6.0 3.0 ± 0.3 CH B CH A VCC OPTION CODE GND 5° TYP. ∅ 2.8 8.7 9.2 ± 0.3 4.34 ± 0.20 3.9 0.8 2x ∅ 2.00 ± 0.02 4.2 7.5 10.1 1.8 3.90 ± 0.10 1.70 ± 0.15 4.2 PIN 1 ID AGILENT XXXXX X 51 7.0 12.6 ± 0.5 6.4 0.14 (OPTICAL CENTER) 8.4 PART # (REFER -05) 15.0 C YYWW DATE CODE 20.2 ± 0.5 C = COUNTRY OF ORIGIN MARKING (REFER -05 FOR DETAILS) 9.8 3.8 0.5 10.8 ± 0.5 Mounting Considerations Note: These dimensions include shaft end play and codewheel warp. All dimensions for mounting the module and codewheel/codestrip should be measured with respect to the two mounting posts, shown above. Mounting Tolerances Case 1 specifies the mounting tolerances required on Rm in order to achieve the respective encoding characteristics shown on page 4. The mounting tolerances are as follows: Case 1: Rm ± 0.13 mm (.005 inches) Recommended Screw Size: M2.5 x 0.45 or 2-56 www.agilent.com/semiconductors For product information and a complete list of distributors, please go to our web site. For technical assistance call: Americas/Canada: +1 (800) 235-0312 or (408) 654-8675 Europe: +49 (0) 6441 92460 China: 10800 650 0017 Hong Kong: (+65) 6271 2451 India, Australia, New Zealand: (+65) 6271 2394 Japan: (+81 3) 3335-8152(Domestic/International), or 0120-61-1280(Domestic Only) Korea: (+65) 6271 2194 Malaysia, Singapore: (+65) 6271 2054 Taiwan: (+65) 6271 2654 Data subject to change. Copyright © 2002 Agilent Technologies, Inc. Obsoletes 5988-3614EN May 10, 2002 5988-6261EN