10612-24-9CS3025

10612 SPECIFICATION CONTROL DRAWING CHEMINAX 77 OHM, AWG 24, 19 STRANDS OF AWG 36, OPTIMIZED SHIELD, DATA BUS CABLE, MIL-STD-1553 Date: 2-13-18 Revision: K THIS SPECIFICATION SHEET FORMS A PART OF THE LATEST ISSUE OF RAYCHEM SPECIFICATION 1200. CONSTRUCTION DETAILS ELECTRICAL CHARACTERISTICS DIMENSIONS ARE NOMINAL VALUES IN INCHES, UNLESS OTHERWISE CHARACTERISTIC IMPEDANCE DESIGNATED. .0250 (.635 mm) .048 ± .002 (1.22 ± .05 mm) .032 (.813 mm) .113 (2.87 mm) CONDUCTORS AWG 24, 19 Strands of AWG 36, Silver-Coated HighStrength Copper Alloy 30.0 pF/ft. (98.4 pF/m) (maximum) ATTENUATION 1.4 dB/100 ft. (4.59 dB/100 m) (maximum) at 1 MHz SURFACE TRANSFER IMPEDANCE 100 milliohms/meter (maximum) (Per SAE AS85485) at 30 MHz ADDITIONAL REQUIREMENTS COMPONENT WIRE PRIOR TO CABLING (Test procedures per SAE AS22759) DIELECTRICS CONDUCTOR RESISTANCE Radiation-Crosslinked, Modified ETFE CROSSLINKING PROOF TEST Colors - Light Blue/White FILLERS Radiation-Crosslinked, Modified ETFE SHIELD AWG 38, Tin-Coated Copper, Optimized 77 ± 5 ohms, Method C at 1 MHz MUTUAL CAPACITANCE 26.5 ohms/1000 ft. (86.9 ohms/km) (nominal) 300 ± 3°C for 1 hour, .500 inch (12.7 mm) mandrel, .375 lb (170 g), 2.5 kV dielectric test INSULATION (DIELECTRIC) ELONGATION TENSILE STRENGTH 50% (minimum) 5000 lbf/in2 (34.5 N/mm2) (minimum) INSULATION FLAWS SPARK TEST IMPULSE TEST 3.0 kV (rms) 8.0 kV (peak) INSULATION RESISTANCE 5000 megohms for 1000 ft. (1524 megohms-km) (minimum) LOW TEMPERATURE-COLD BEND -65 ± 3°C for 4 hours, .750 inch (19.1 mm) mandrel, 1.00 lb (454 g), 2.5 kV dielectric test SHRINKAGE 200 ± 3°C for 1 hour, .125 inch (3.18 mm) (maximum) in 12 inches (305 mm) FINISHED CABLE (Test procedures per NEMA WC 27500, unless otherwise specified) BLOCKING CABLE LAY LENGTH .129 (3.28 mm) (nominal) .137 (3.48 mm) (maximum) JACKET Radiation-Crosslinked, Modified ETFE CROSSLINKED VERIFICATION FLAMMABILITY (Method B of Spec 1200) JACKET ELONGATION TENSILE STRENGTH JACKET FLAWS SPARK TEST IMPULSE TEST JACKET THICKNESS LOW TEMPERATURE-COLD BEND 200°C for 6 hours .75 inch (19.1 mm) (minimum), 1.25 inches (31.8 mm) (maximum) 300 ± 5°C for 6 hours, 6.00 inch (152 mm) mandrel 3 seconds (maximum); 3 inches (76.2 mm) (maximum); no flaming of facial tissue 50% (minimum) 5000 lbf/in2 (34.5 N/mm2) (minimum) 1.0 kV (rms) 6.0 kV (peak) .008 inch (.203 mm) (nominal) -55 ± 5°C for 4 hours, 6.00 inch (152 mm) mandrel 1000 volts (rms) (minimum) VOLTAGE WITHSTAND (DIELECTRIC) 15.9 lbs/1000 ft. (23.7 kg/km) (maximum) The conductor AWG size and outer jacket color will be appended to WEIGHT the part number. Unless otherwise specified, outer jacket color will CABLE IDENTIFICATION: Outer jacket shall be marked in contrasting color at 12 be white designated by a "-9" in accordance with MIL-STD-681, inch (305 mm) (nominal) intervals between marks as follows: "10612 RAYCHEM" (e.g. 10612-24-9). Other codes and suffixes may be added to the part number, as necessary, to capture any additional requirements imposed by the purchase order. ENGINEERING REFERENCE TEMPERATURE RATING 150°C (maximum) Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. TE Connectivity also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. Page 1 of 1 Cheminax, Raychem, TE Connectivity, and TE connectivity (logo) are trademarks. Raychem Wire & Cable 501 Oakside Avenue Redwood City, California 94063-3800 Phone: 1-800-522-6752 Fax: 1-650-361-6297 THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. © 2009-2018 TE Connectivity Ltd. family of companies. All Rights Reserved.