2-2151187-2

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 PART NUMBER RELEASED FOR PUBLICATION 6 REVISION DESCRIPTION FEED TYPE D FINE CRIMP HEIGHT ADJUST MECHANICAL 7-2151187-1 D MECHANICAL AND CRIMP TOOLING KIT MECHANICAL 7-2151187-2 E 7- 2151187 -7 A E 3 2 LOC 2151187 -1 2151187 -2 4 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 FINE CRIMP HEIGHT ADJUST REVISIONS DIST A ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER 1 66 P LTR PNEUMATIC PNEUMATIC AND CRIMP TOOLING KIT DESCRIPTION DATE DWN APVD B ECR-13-015652 08OCT2013 YY UG C ECR-16-002457 19NOV2016 XZ GB D ECR-18-013011 16AUG2018 FL TE E ECR-22-147681 28JUL2022 FZ TE PNEUMATIC CRIMP TOOLING KIT - D D CRIMP WIRE INSUL APPLICATOR DATA SIZE TYPE F F 2.79 mm [.110] 4.06 mm [.160] APPLICATOR INSTRUCTIONS 408-35042 TE TERMINAL TERMINAL DATA: RECEPTACLE MIC MKII TERMINAL NAME: WIRE STRIP LENGTH 3.51-5.49 [.138-.216 IN] C TERMINAL APPLICATION SPECIFICATION n 114-5071 - TE CRIMP SPECIFICATION - INSULATION DIAMETER RANGE - 2.16-3.43 mm [.085-.135 IN] - - - - 3 - 172773-5 TE TERMINAL 172773-2 C1__DWG_PN_1_0 C1__DWG_PN_1_1 172773-6 C1__DWG_PN_1_2 - TERMINALS APPLIED TE TERMINAL 172773-1 - C1__DWG_PN_2_0 C1__DWG_PN_2_1 TE TERMINAL 172773-3 C1__DWG_PN_2_2 172773-7 C1__DWG_PN_3_0 C1__DWG_PN_3_1 - TE TERMINAL 172773-4 - C1__DWG_PN_4_0 - C1__DWG_PN_4_1 - C1__DWG_PN_3_2 - WIRE SIZE 14 AWG OR 2.00mm2 16 AWG OR 1.25mm2 18 AWG OR 0.85mm2 20 AWG OR 0.50mm2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 W1__DWG_WGAUGE_4 1.68+/-0.05 [.066+/-.002] 1.55+/-0.05 [.061+/-.002] 1.42+/-0.05 [.056+/-.002] 1.35+/-0.05 [.053+/-.002] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 W1__DWG_CRIMP_HT_4 6.0 7.2 8.6 9.2 - 4 - W1__FA_SETTING_1 - W1__FA_SETTING_2 - W1__FA_SETTING_3 - W1__FA_SETTING_4 - 1 2 B 3 4 - RECOMMENDED SPARE PARTS - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. - APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. - 5. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 - 1 1 1 1 - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. A AMP 4805 REV 31MAR2000 1 1 1 - - 1 1 1 1 1 1 1 1 mm & 4 of 4) MATERIAL - PART NO 1 1 - REF REF REF REF 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 2 1 - 1 1 2 1 - 1 1 1 1 - 1 1 1 1 - 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 2 1 1 1 2 1 1 1 1 1 1 1 1 1 - 1 1 2 - 1 1 1 1 1 - 2 1 2 - 4 2 1 1 1 4 2 1 1 1 4 2 1 1 1 4 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 2 1 1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: -1 1 - - 1 1 1 1 1 1 1 1 - 1 1 1 2119641-1 2119082-9 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 994970-2 1-18028-2 2844908-1 2844907-1 455888-6 1803607-3 2119740-1 2168078-1 2168083-2 5-18022-5 1338685-1 2168083-3 2168083-3 1803382-6 18023-9 2119652-1 2119653-1 1803583-9 1803515-1 1803602-1 2-1752356-0 2079383-5 2-2844962-0 2844992-1 455888-6 1320928-1 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 1803095-1 1633923-3 1-240641-1 2119757-8 238011-4 1-1633961-4 455888-3 456408-2 - -77 -72 -71 -2 ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 1 1 TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - FEED CAM, AIR FEED CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC WASHER, FLAT, REG M4 SCREW, LOCKING POST, LOCKING SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, SKT HD CAP, RoHS, M4 X 8.0 SCR, HEX HD CAP, M4 X 6.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 12.0 SCR, SKT HD CAP, RoHS, M4 X 12.0 HOLD DOWN, SPRING LOADED SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF ATLANTIC SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION F PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM DWN 04NOV2011 CHK 04NOV2011 APVD 04NOV2011 C.CHEN S.XI I.CRUZ NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2119083 1 7-18023-7 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 1-18028-2 1 2844908 1 2844907 1 455888-6 1 1803607_3 1 2119740-1 2 2168078-1 1 2168083-2 1 5-18022-5 1 1338685-1 4 2168083-3 2 2168083-3 1 1803382-6 3 18023-9 1 2119652 1 2119653 1 1803583-9 1 1803515-1 1 1803602-1 1 2-1752356-0 2 2079383-5 2 2-2844962-0 1 2844992-1 1 455888-6 1 1320928-1 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 1803095-1 1 1633923-3 1 1-240641-1 .. 1 ITEM_6 1 2119757-8 1 238011-4 1 1-1633961-4 1 455888-3 1 456408-2 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2079764_APP 248 244 243 242 241 239 238 164 119 99 98 82 71 67 66 60 59 56 54 53 50 49 48 47 46 44 41 34 33 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2119082-9 DESCRIPTION PRODUCT SPEC - 1 2119641-1 Ocean Side Feed Applicator - DRAWING NO 2151187 SCALE 1:2 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV E C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL A D 239 D 59 44 56 2 PNEUMATIC 244 243 A 242 238 53 50 59 C 3 2 8 7 82 1 1.0 REF 0.5 34 REF 1 C 2 SEE DETAIL A 3 1 4 56 TERMINAL SUPPORT LOCATION 28 5 41 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 44.25 0.05 44 REF 66 DETAIL A 164 67 2 33 A 24 B RAM SET-UP 19 30 B 20 21 29 9 1 ITEM 30 LOCATED AT FRONT HOLES 12 241 CAM POSITIONS 13 47 29 REF 1 11 30mm STROKE 30mm STROKE 30mm STROKE 30 REF 46 98 99 34 54 8 1 60 54 10 1 119 FEED TRACK POSITION GUIDE BY INSULATION BARREL 248 48 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 04NOV2011 CHK 04NOV2011 APVD 04NOV2011 C.CHEN S.XI I.CRUZ TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2151187 SCALE 1:2 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV E 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 REVISION DESCRIPTION FEED TYPE 2- 2151187 -1 D FINE CRIMP HEIGHT ADJUST MECHANICAL 7- 2151187 -7 A CRIMP TOOLING KIT - E 3 2 LOC PART NUMBER 2- 2151187 -2 4 20 ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 5 FINE CRIMP HEIGHT ADJUST REVISIONS DIST A PACIFIC VERSION TERMINATOR INTERFACE ADAPTER 1 66 P LTR - DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - PNEUMATIC D D CRIMP WIRE INSUL APPLICATOR DATA SIZE TYPE F F 2.79 mm [.110] 4.06 mm [.160] APPLICATOR INSTRUCTIONS 408-35042 TE TERMINAL TERMINAL DATA: RECEPTACLE MIC MKII TERMINAL NAME: WIRE STRIP LENGTH 3.51-5.49 [.138-.216 IN] C TERMINAL APPLICATION SPECIFICATION n 114-5071 - TE CRIMP SPECIFICATION - INSULATION DIAMETER RANGE - 2.16-3.43 mm [.085-.135 IN] - - - - TE TERMINAL 172773-1 172773-5 TE TERMINAL 172773-2 172773-6 C1__DWG_PN_1_1 C1__DWG_PN_1_2 TE TERMINAL C1__DWG_PN_2_1 C1__DWG_PN_2_2 172773-3 172773-7 C1__DWG_PN_3_0 - TE TERMINAL 172773-4 C1__DWG_PN_3_1 1 - 14 AWG OR 2.00mm2 16 AWG OR 1.25mm2 18 AWG OR 0.85mm2 20 AWG OR 0.50mm2 W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 W1__DWG_WGAUGE_4 1.68+/-0.05 [.066+/-.002] 1.55+/-0.05 [.061+/-.002] 1.42+/-0.05 [.056+/-.002] 1.35+/-0.05 [.053+/-.002] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 W1__DWG_CRIMP_HT_4 6.0 7.2 8.6 9.2 - CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. 1 1 - 1 1 - 1 1 1 1 - 1 1 - 1 1 1 1 1 - 1 1 1 - - - 1 - 1 1 1 1 - 1 1 1 1 1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: mm & 2 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 MECHANICAL FEED ASSEMBLY AIR FEED MODULE COUNTER, MAGNETIC FEED CAM, AIR FEED SCR, SKT HD CAP, RoHS, M4 X 16 SCR, SKT HD CAP, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM ASSEMBLY, SF PACIFIC WASHER, FLAT, REG M4 SCREW, LOCKING POST, LOCKING SPACER, CRIMPER DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 SCR, HEX HD CAP, M4 X 6.0 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 12.0 HOLD DOWN, SPRING LOADED SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) SPACER, CYLINDRICAL, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION SPACER DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION F PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM PART NO -77 -22 -21 PACIFIC VERSION AMP 4805 REV 31MAR2000 1 1 - Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 1 1 - A 1 1 - 1 1 1 - 1 2 1 - 1 2 2 - 1 1 2 - *WARNING ON INSTALLATION, SET WIRE DISC TO CRIMP HEIGHT REFERENCE SETTING FOR LARGEST WIRE SIZE. CRIMP HEIGHT REFERENCE SETTINGS GREATER THAN THE VALUE SHOWN MAY CAUSE DAMAGE TO THE CRIMP TOOLING, REFER TO THE INSTRUCTION SHEET FOR PROPER SETUP AND ADJUSTMENTS. 1 1 - 1 1 1 - 1 2 - - 1 1 1 - 1 2 1 - 5. UNLESS SPECIFIED OTHERWISE TORQUE VALUES SHALL BE USED PER DOCUMENT, 101-35000. 1 2 - 4 1 1 - APPLY PART NUMBER 2-23419-6 LOCTITE TO THREADS OF ITEM 242. 2 1 - 3 1 2 - REFER TO SUPPLIED INSTRUCTION SHEET FOR CLEANING, LUBRICATION AND STORAGE OF APPLICATOR. 1 1 - 2 1 1 - RECOMMENDED SPARE PARTS 1 1 - 1 1 1 - B 1 1 - W1__FA_SETTING_4 1 1 - W1__FA_SETTING_3 1 1 - W1__FA_SETTING_2 1 1 W1__FA_SETTING_1 4 - - 4 1 4 - CRIMP HEIGHT mm [INCH] - 1 - WIRE SIZE - REF REF - C1__DWG_PN_3_2 1 1 - C1__DWG_PN_4_1 1 - - C1__DWG_PN_4_0 1 1 C1__DWG_PN_2_0 1 1 - 2119082-9 2079764-1 2119083-1 7-18023-7 2119580-1 2844940-1 994970-2 2119641-2 2168083-8 2168083-9 2119653-2 1-1803583-0 1803516-1 1-18028-2 2844908-1 2844907-1 455888-6 1803607-3 2119740-1 2168078-1 5-18022-5 1338685-1 2168083-3 1803382-6 18023-9 2119652-1 1803602-1 2-1752356-0 2079383-5 2-2844962-0 2844992-1 455888-6 1320928-1 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 1803095-1 1633923-3 1-240641-1 2119757-8 238011-4 1-1633961-4 455888-3 456408-2 1 1 - 3 TERMINALS APPLIED C1__DWG_PN_1_0 1 DWN 04NOV2011 CHK 04NOV2011 APVD 04NOV2011 C.CHEN S.XI I.CRUZ NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 7-18023-7 1 2119580-1 1 2844940-1 1 COUNTER_994970 1 2119641-2 1 2168083-8 4 2168083-9 1 2119653-2 1 1-1803583-0 1 1803516-1 1 1-18028-2 1 2844908 1 2844907 1 455888-6 1 1803607_3 1 2119740-1 2 2168078-1 1 5-18022-5 1 1338685-1 2 2168083-3 1 1803382-6 3 18023-9 1 2119652 1 1803602-1 1 2-1752356-0 2 2079383-5 2 2-2844962-0 1 2844992-1 1 455888-6 1 1320928-1 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 1803095-1 1 1633923-3 1 1-240641-1 .. 1 ITEM_6 1 2119757-8 1 238011-4 1 1-1633961-4 1 455888-3 1 456408-2 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2119083 244 243 242 241 239 238 164 151 144 143 142 141 140 119 99 98 82 71 67 66 59 56 53 50 49 48 41 34 33 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2079764_APP DESCRIPTION PRODUCT SPEC - 1 2119082-9 Ocean Side Feed Applicator - DRAWING NO 2151187 SCALE 1:2 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV E C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 20 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL A D 140 239 59 53 56 PNEUMATIC 2 D 244 50 243 7 242 82 A 1 238 2 3 1.0 1 REF 8 2 3 59 1 0.5 34 4 REF 28 5 TERMINAL SUPPORT LOCATION 41 C C SEE DETAIL A 56 164 FEED SPRING SETTING POSITION (SHOWN FROM REAR SIDE) 66 2 33 67 A 24 35.22 0.05 140 19 REF 20 30 DETAIL A 21 29 9 1 RAM SET-UP 12 241 B 13 B 1 11 119 CAM POSITIONS 30mm STROKE 141 99 34 143 8 1 144 143 10 30 1 REF REF 29 30mm STROKE 30mm STROKE 142 98 ITEM 30 LOCATED AT FRONT HOLES 151 FEED TRACK POSITION GUIDE BY INSULATION BARREL 48 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 04NOV2011 CHK 04NOV2011 APVD 04NOV2011 C.CHEN S.XI I.CRUZ TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2151187 SCALE 1:2 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV E