7724Y3664-9

7724Y3664 SPECIFICATION CONTROL DRAWING Date: 77 OHM, AWG 24, 19 STRANDS OF AWG 36 DATA BUS CABLE, MIL-STD-1553 CHEMINAX 8-8-18 Revision: E THIS SPECIFICATION SHEET FORMS A PART OF THE LATEST ISSUE OF RAYCHEM SPECIFICATION 1200. CONSTRUCTION DETAILS DIMENSIONS ARE NOMINAL VALUES IN INCHES, UNLESS OTHERWISE DESIGNATED. .0250 .0515 + .002 - .001 .035 CONDUCTORS AWG 24, 19 Strands of AWG 36, Silver-Coated HighStrength Copper Alloy DIELECTRICS Radiation-Crosslinked, Modified ETFE Colors - Light Blue/White FILLERS Radiation-Crosslinked, Modified ETFE .120 1st SHIELD AWG 38, Tin-Coated Copper ELECTRICAL CHARACTERISTICS CHARACTERISTIC IMPEDANCE 77 ± 5 ohms, Method C at 1 MHz MUTUAL CAPACITANCE 30.0 pF/ft. (maximum) ATTENUATION 1.4 dB/100 ft. (maximum) at 1 MHz ADDITIONAL REQUIREMENTS COMPONENT WIRE PRIOR TO CABLING (Test procedures per SAE AS22759) CONDUCTOR RESISTANCE 26.5 ohms/1000 ft. (nominal) CROSSLINKING PROOF TEST 300 ± 3°C for 1 hour, .500 inch mandrel, .375 lb, 2.5 kV dielectric test INSULATION (DIELECTRIC) ELONGATION TENSILE STRENGTH 50% (minimum) 5000 lbf/in2 (minimum) INSULATION FLAWS SPARK TEST IMPULSE TEST 3.0 kV (rms) 8.0 kV (peak) INSULATION RESISTANCE 5000 megohms for 1000 ft. (minimum) LOW TEMPERATURE-COLD BEND -65 ± 3°C for 4 hours, .500 inch mandrel, 1.00 lb, 2.5 kV dielectric test SHRINKAGE 200 ± 3°C for 1 hour, .125 inch (maximum) in 12 inches FINISHED CABLE (Test procedures per NEMA WC 27500, unless otherwise specified) BLOCKING .124 .141 .157 WRAP Separator Tape 2nd SHIELD AWG 38, Tin-Coated Copper JACKET Radiation-Crosslinked, Modified ETFE Designate outer jacket color with a dash number in accordance with MIL-STD-681. Unless otherwise specified, outer jacket color will be white designated by a "-9" appended to the part number, e.g. 7724Y3664-9. Other codes and suffixes may be added to the part number, as necessary, to capture any additional requirements imposed by the purchase order. 200°C for 6 hours CABLE LAY LENGTH .75 inch (minimum), 1.25 inches (maximum) CROSSLINKED VERIFICATION 300 ± 5°C for 6 hours, 6.00 inch mandrel FLAMMABILITY (Method B of Spec 1200) 3 seconds (maximum), 3 inches (maximum); no flaming of facial tissue JACKET ELONGATION TENSILE STRENGTH 50% (minimum) 5000 lbf/in2 (minimum) JACKET FLAWS SPARK TEST IMPULSE TEST 1.0 kV (rms) 6.0 kV (peak) JACKET THICKNESS .008 inch (nominal) LOW TEMPERATURE-COLD BEND -55 ± 5°C for 4 hours, 6.00 inch mandrel SHIELD COVERAGE (each) 85% (minimum) VOLTAGE WITHSTAND (DIELECTRIC) 1000 volts (rms) (minimum) WRAP .001 inch thick (nominal), 25% overlap (minimum) CABLE IDENTIFICATION: Outer jacket shall be marked in contrasting color at 12 inch (nominal) intervals between marks follows: 7724Y3664-* RAYCHEM Where * = applicable jacket color WEIGHT 22.4 lbs/1000 ft. (nominal) ENGINEERING REFERENCE TEMPERATURE RATING 150°C (maximum) Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. TE Connectivity also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. Page 1 of 1 Cheminax, Raychem, TE Connectivity, and TE connectivity (logo) are trademarks. Raychem Wire & Cable 501 Oakside Avenue Redwood City, California 94063-3800 Phone: 1-800-522-6752 Fax: 1-650-361-6297 THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. © 2012-2018 TE Connectivity Ltd. family of companies. All Rights Reserved.