CN0557-000

ANTI-ROTATIONAL SET SCREW 9 CODE 18 - BRAID TAIL BACKSHELL 218M916-19B08 SERIES ORDER NUMBER (TABLE 1) MANUFACTURER CODE (TABLE 3) MATERIAL REFER TO CH00-0250-004 FINISH REFER TO CH00-0250-004 2 ENTRY SIZE (TABLE 2) NOTES: 1. THIS PRODUCT IS DESIGNED TO TERMINATE A HEAT SHRINKABLE LIPPED BOOT TO A CONNECTOR. 2. FOR ADDITIONAL DIMENSIONS, ORDERING INFORMATION AND MODIFICATION, SEE CH00-0250-004. 3. BACKSHELL TO BE PERMANENTLY MARKED/BAGGED AND LABELLED WITH CODE IDENTIFICATION NUMBER AND PART NUMBER. (e.g. 06090-218M916-19B08). 4. WHEN ENTRY SIZE EXCEEDS "MAX ENTRY", A 2 PIECE BACKSHELL (TYPE 2) IS SUPPLIED. 5. BACKSHELL MATES TO MIL-DTL-5015D, CLASS A, E & R, MS3100, MS3101 &MS3106. RESILIENT INSERT, SOLDER TYPE AND BENDIX 10-214, CANNON CA-RX COMMERCIAL CRIMP TYPE. 6. BRAID TERMINATION RING MAY BE SUPPLIED AS TINEL-LOCK SHAPE MEMORY RING AT MANUFACTURERS OPTION. 7. ALL THREAD SIZES FOR ORDER NO. APPLY. 8. ADDITIONAL PIECE(S) SUPPLIED WHEN CONNECTOR MFR IS UNKNOWN ("D" IN TABLE 3) AND ENTRY SIZE DOES NOT EXCEED VALUE IN TABLE 1. 9. ANTI-ROTATIONAL SET SCREW, THREE #4-40 THREADED HOLES 120° ±5° APART, SINGLE MATING SET SCREW SUPPLIED. DRAWN B.VESA DATE CHECKED 08/10/2015 APPROVED K.SHEPPARD 16/10/2015 APPROVED LTR D E H.SMITH 3RD ANGLE PROJECTION NOT TO SCALE 08/10/2015 23/10/2015 REVISIONS DESCRIPTION REVISED PER ECO-14-008400 REVISED PER ECO-15-015326 UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM ANGULAR +/- 1° DATE 04.06.14 APPROVED I.MYONG 23.10.15 H.SMITH TE CAGE CODE: 06090 POLAMCO/TE CAGE CODE: U5792 TITLE: BRAID TAIL BACKSHELL ASSY USED ON: MIL-DTL-5015D TE CONNECTIVITY - POLAMCO LTD RESERVES THE RIGHT TO AMEND THIS DRAWING AND THE INFORMATION SET FORTH HEREON AT ANY TIME. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. DRAWING NO: DRAWING REV: SHT 218M9XX E 1 IF MAX ENTRY IS EXCEEDED, BACKSHELL WILL BE SUPPLIED AS TYPE 2 XXXX ØB ØK M SILICONE O-RING J E XXXX A THREAD SILICONE O-RING T A THREAD ØB SILICONE O-RING H 19,50 `0,50 W 152,40 MIN ØZ ØY TINNED COPPER BRAID 4 152,40 MIN PART MARK HERE PART MARK HERE TINNED COPPER BRAID 90° BACKSHELL - TYPE 2 90° BACKSHELL - TYPE 1 M W 19,50 `0,50 H 152,40 MIN 152,40 MIN J E T 90° BACKSHELL - TYPE 1 STAINLESS STEEL AND NICKEL ALUMINIUM BRONZE DRAWN B.VESA DATE CHECKED 08/10/2015 APPROVED K.SHEPPARD 16/10/2015 APPROVED LTR D E H.SMITH 3RD ANGLE PROJECTION NOT TO SCALE 08/10/2015 23/10/2015 REVISIONS DESCRIPTION REVISED PER ECO-14-008400 REVISED PER ECO-15-015326 UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM ANGULAR +/- 1° DATE 04.06.14 APPROVED I.MYONG 23.10.15 H.SMITH TE CAGE CODE: 06090 POLAMCO/TE CAGE CODE: U5792 90° BACKSHELL - TYPE 2 STAINLESS STEEL AND NICKEL ALUMINIUM BRONZE TITLE: BRAID TAIL BACKSHELL ASSY USED ON: MIL-DTL-5015D TE CONNECTIVITY - POLAMCO LTD RESERVES THE RIGHT TO AMEND THIS DRAWING AND THE INFORMATION SET FORTH HEREON AT ANY TIME. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. DRAWING NO: DRAWING REV: SHT 218M9XX E 2 THESE DIMENSIONS APPLY IF BACKSHELL IS STAINLESS STEEL OR NICKEL ALUMINIUM BRONZE TABLE 1 ORDER NUMBER 8S 8S 8S 8S 10S 10SL 10SL 10SL 12 & 12S 12 & 12S 12 & 12S 14 & 14S 16 & 16S 18 20 20 20 22 24 28 32 32 32 36 36 36 36 36 40 40 40 44 48 48 48 08 10 11 12 14 16 18 20 22 24 28 32 36 40 44 48 TABLE 2 ENTRY SIZE 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 20 21 22 24 28 DRAWN SHELL SIZE ØK MAX NA NA 21,0 21,0 21,0 24,5 24,5 29,0 32,5 32,5 35,5 35,5 37,0 37,0 40,0 40,0 43,5 48,5 48,5 52,1 58,5 B.VESA ØZ REF 4,77 6,35 7,92 9,52 11,12 12,70 14,27 15,87 17,47 19,05 20,62 22,23 23,82 25,40 26,98 28,60 31,80 33,34 35,00 38,10 44,45 DATE APPROVED K.SHEPPARD 16/10/2015 E H.SMITH ØY REF 13,1 13,1 13,1 17,9 17,9 17,9 17,9 24,2 24,2 24,2 24,2 30,6 30,6 30,6 33,2 33,2 42,0 42,0 42,0 42,0 49,0 23/10/2015 REVISIONS DESCRIPTION REVISED PER ECO-14-008400 REVISED PER ECO-15-015326 H ±0,5 NA NA 24,0 24,0 24,0 27,0 27,0 31,0 34,0 34,0 35,0 35,0 38,0 38,0 42,0 42,0 45,0 54,5 54,5 58,0 65,5 M ±0,5 NA NA 15,5 15,5 15,5 17,0 17,0 19,5 21,0 21,0 20,0 20,0 21,5 21,5 24,0 24,0 25,5 31,0 31,0 33,0 36,5 3RD ANGLE PROJECTION NOT TO SCALE 08/10/2015 08/10/2015 LTR D MAX ENTRY 4 04 04 04 04 06 07 07 07 08 08 08 10 12 13 16 16 16 18 20 24 24 24 24 28 28 28 28 28 28 28 28 28 28 28 28 A THREAD ØB MAX W ±0,5 T ±0,5 E ±0,5 W ±0,5 T ±0,5 E ±0,5 3/8-32 UNEF 7/16-28 UNEF 7/16-27 UNS 7 1/2-28 UNEF 9/16-24 UNEF 5/8-24 UNEF 7 5/8-24 UNEF 11/16-24 UNEF 7 3/4-20UNEF 7/8-20 UNEF 1-20 UNEF 1 1/8-18 UNEF 1 1/8-24 UNS 7 1 1/4-18 UNEF 1 3/8-18 UNEF 1 5/8-18 UNEF 1 7/8-16 UN 1 29/32-18 UN 7 2 1/16-16 UNS 2 1/16-20 UNS 2 1/8-16 UN 2 1/8-18 UNS 7 2 5/16-16 UN 2 3/8-16UN 7 2 5/8-16 UN 2 13/16-18 UNS 2 7/8-16 UN 7 18,5 18,1 18,5 18,5 19,8 21,6 23,2 23,2 23,0 24,9 24,9 27,7 30,1 34,4 37,6 37,6 37,6 40,6 43,6 48,6 54,9 54,9 54,9 64,6 64,6 64,6 64,6 64,6 70,6 70,6 69,3 82,0 82,0 82,0 82,0 21,7 21,7 21,7 21,7 23,2 25,0 27,2 27,2 27,2 27,2 27,2 30,7 34,2 37,2 40,7 40,7 40,7 43,7 46,7 51,7 58,4 58,4 58,4 67,7 67,7 67,7 67,7 67,7 72,2 72,2 72,2 77,6 MAX 84,0 MAX 84,0 MAX 84,0 MAX 15,2 15,2 15,2 15,2 15,7 16,5 17,5 17,5 17,5 17,5 17,5 19,5 21,5 23,0 24,5 24,5 24,5 26,0 27,5 30,0 32,7 32,7 32,7 38,0 38,0 38,0 38,0 38,0 41,1 41,1 41,1 41,1 44,1 47,2 47,2 24,0 24,0 24,0 24,0 25,7 25,7 25,7 25,7 26,3 26,3 26,3 28,7 30,4 32,0 33,6 33,6 33,6 35,1 36,6 39,1 42,3 42,3 42,3 47,1 47,1 47,1 47,1 47,1 49,3 49,3 49,3 61,5 MAX 61,5 MAX 61,5 MAX 61,5 MAX 21,7 21,7 21,7 21,7 23,2 27,2 27,2 27,2 27,2 27,2 27,2 30,7 34,2 37,2 40,7 40,7 40,7 43,7 46,7 51,7 58,4 58,4 58,4 67,7 67,7 67,7 67,7 67,7 72,2 72,2 72,2 72,2 75,5 75,5 75,5 15,2 15,2 15,2 15,2 15,7 17,5 17,5 17,5 17,5 17,5 17,5 19,5 21,5 23,0 24,5 24,5 24,5 26,0 27,5 30,0 32,2 32,2 32,2 38,0 38,0 38,0 38,0 38,0 41,1 41,1 41,1 41,1 40,8 40,8 40,8 24,0 24,0 24,0 24,0 25,7 25,7 25,7 25,7 27,0 27,0 27,0 28,7 30,4 32,0 33,6 33,6 33,6 35,1 36,6 39,1 42,3 42,3 42,3 47,1 47,1 47,1 47,1 47,1 49,3 49,3 49,3 61,5 MAX 61,5 MAX 61,5 MAX 61,5 MAX THESE DIMENSIONS APPLY IF BACKSHELL IS STAINLESS STEEL OR NICKEL ALUMINIUM BRONZE CHECKED APPROVED MFR CODE TABLE 3 B C A, R D 8 C A, B, R D 8 B, C A, R D 8 A, B, C R D 8 B, C A, R D 8 B R C A D 8 B A, C, R D 8 C A, R D 8 UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM ANGULAR +/- 1° DATE 04.06.14 APPROVED I.MYONG 23.10.15 H.SMITH TE CAGE CODE: 06090 POLAMCO/TE CAGE CODE: U5792 J ±0,5 NA NA 25,7 25,7 25,7 27,2 27,2 28,7 30,4 30,4 32,1 32,1 33,7 33,7 35,2 35,2 36,7 39,8 39,8 43,8 48,9 H ±0,5 NA NA 24,3 24,3 24,3 28,3 28,3 31,1 34,2 34,2 38,5 38,5 40,7 40,7 43,7 43,7 46,4 50,0 50,0 53,5 60,3 M ±0,5 NA NA 17,2 17,2 17,2 19,4 19,4 21,0 22,8 22,8 25,3 25,3 26,1 26,1 27,6 27,6 29,1 31,0 31,0 33,0 36,5 J ±0,5 NA NA 25,7 25,7 25,7 27,2 27,2 28,7 30,4 30,4 32,1 32,1 33,7 33,7 35,2 35,2 36,7 39,8 39,8 43,8 48,9 TABLE 3 MFR CODE A B C D R - CONNECTOR MANUFACTURER (MS 3100, MS 3101 & MS 3106) AMPHENOL - CLASS A BENDIX - CLASS A, E & R CANNON - CLASS A, E & R MFR UNKNOWN, CLASS A, E & R AMPHENOL - CLASS R MFR CODE NOT REQUIRED TITLE: BRAID TAIL BACKSHELL ASSY USED ON: MIL-DTL-5015D TE CONNECTIVITY - POLAMCO LTD RESERVES THE RIGHT TO AMEND THIS DRAWING AND THE INFORMATION SET FORTH HEREON AT ANY TIME. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. DRAWING NO: DRAWING REV: SHT 218M9XX E 3