TLM2AER01JTD

SMD Current Sense Metal Chip Resistor Type TLM Series Key Features Low resistance resistor for current detection Small size to power ratio Metal foil construction ensures high reliability and performance with very low and stable TCR Designed for current sense circuits in power electronic systems Terminal finish matte Sn over Ni TE Connectivity is pleased to introduce this low ohmic metal chip resistor designed for current sense circuits in power electronic systems. Supplied as standard on tape and reel for automatic insertion processes. Characteristics – Electrical Type Power Rating @ 70°C TLM 1J 0.125W TLM 2A 0.25W TLM 2B 0.5W TLM 2H 0.75W TLM 3A 1W Operating Temp. Range Resistance Range (mΩ) ±1% ±2% ±5% 10 - 19 20 - 100 10 - 19 20 - 100 10 – 19 -55~+55°C 20 - 100 10 – 19 20 - 100 10 – 19 20 - 100 TCR (PPM/°C) ±100 ±50 ±100 ±100 ±50 ±100 ±100 ±50 ±100 ±100 ±50 ±100 ±100 ±50 ±100 Operating Voltage=√(P*R) ; Overload Voltage=2.5*√(P*R) ; Operating Current=√(P/R) 1773269-1 CIS WR 01/2015 Dimensions in millimetres unless otherwise specified Dimensions Shown for reference purposes only. Specifications subject to change For Email, phone or live chat, go to: www.te.com/help SMD Current Sense Metal Chip Resistor Power derating curve For resistors operated in ambient temperatures above 70°C, power rating must be derated in accordance with this curve. Environmental Characteristics Item Temperature Coefficient of Resistance (TCR) Short Term Overload Insulation Resistance Endurance Requirement As Spec. Damp Heat with Load ±(1.0%+0.05Ω) Dry Heat Bending Strength ±(0.5%+0.05Ω) As Spec. Solderability Resistance to Soldering Heat Voltage Proof Leaching 95% min. coverage ±(0.5%+0.05Ω) No breakdown or flashover Individual leaching area ≦5% Total leaching area ≦10% ±(0.5%+0.05Ω) Rapid Change of Temperature ±(0.5%+0.05Ω) ≧10G ±(1.0%+0.05Ω) Test Method -55°C~+125°C, 25°C is the reference temperature 5 X Rated Power for 5 seconds Max. overload voltage for 1 minute 70±2°C, Max. working voltage for 1000 hrs with 1.5 hrs “ON” and 0.5 hrs “OFF” 40±2°C, 90~95% R.H. Max. working voltage for 1000 hrs with 1.5 hrs “ON” and 0.5 hrs “OFF” at +155°C for 1000 hrs Bending once for 5 seconds 2010, 2512 sizes: 2mm Other sizes: 3mm 245±5°C for 3 seconds 260±5°C for 10 seconds 1.42 times RCWV (RMS) for 1 minute 260±5°C for 30 seconds -55°C to +155°C, 5 cycles Reference Standards: IEC 60115-1, 60068-2-58; JIS-C 5201-1 Storage Temperature: 25±3°C; Humidity < 80%RH 1773269-1 CIS WR 01/2015 Dimensions in millimetres unless otherwise specified Dimensions Shown for reference purposes only. Specifications subject to change For Email, phone or live chat, go to: www.te.com/help SMD Current Sense Metal Chip Resistor Construction: 1 2 3 4 Alumina Substrate Bottom Electrode (Cu) Top Electrode (NiCr) Edge Electrode (NiCr) 5 6 7 8 Barrier Layer (Ni) External Electrode (Sn) Adhesive (Acrylic) Resistor Layer (Alloy) 9 10 Primary Overcoat (Epoxy) Marking (Epoxy) Dimensions Type TLM 1J TLM 2A TLM 2B TLM 2H TLM 3A Resistance Range (mΩ) 10 – 29 30 - 100 10 – 29 30 - 100 10 - 29 30 - 100 10 - 29 30 - 100 10 – 29 30 - 100 L W T D1 D2 1.55±0.10 1.55±0.10 2.00±0.15 2.00±0.15 3.05±0.15 3.05±0.15 5.00±0.20 5.00±0.20 6.30±0.20 6.30±0.20 0.85±0.10 0.85±0.10 1.25±0.15 1.25±0.15 1.55±0.15 1.55±0.15 2.50±0.20 2.50±0.20 3.15±0.20 3.15±0.20 0.40±0.10 0.40±0.10 0.55±0.10 0.52±0.10 0.58±0.15 0.55±0.15 0.58±0.15 0.55±0.15 0.58±0.15 0.55±0.15 0.30±0.15 0.30±0.15 0.30±0.20 0.30±0.20 0.50±0.25 0.50±0.25 0.60±0.30 0.60±0.30 0.60±0.30 0.60±0.30 0.45±0.15 0.35±0.15 0.50±0.20 0.35±0.20 0.90±0.25 0.60±0.25 1.50±0.30 0.90±0.30 1.80±0.30 1.20±0.30 Recommended Land Pattern: Type TLM1J TLM2A TLM2B TLM2H TLM3A 1773269-1 CIS WR 01/2015 Dimensions in millimetres unless otherwise specified Resistance Range (mΩ) 10 – 29 30 - 100 10 – 29 30 - 100 10 - 29 30 - 100 10 - 29 30 - 100 10 – 29 30 - 100 Dimensions Shown for reference purposes only. Specifications subject to change A B C 0.40 0.70 0.80 1.00 0.9 1.50 1.70 2.80 2.30 3.60 1.20 1.05 1.10 1.00 1.70 1.40 2.35 1.80 2.90 2.25 0.50 0.90 1.35 1.35 1.70 1.70 2.50 2.50 3.10 3.10 For Email, phone or live chat, go to: www.te.com/help SMD Current Sense Metal Chip Resistor Packaging Packaging Quantity and Reel Specification: Type ΦA ΦB ΦC W T Paper Tape (EA) TLM1J TLM2A TLM2B TLM2H TLM3A 178.0±1.0 178.0±1.0 178.0±1.0 178.0±1.0 178.0±1.0 60.0±1.0 60.0±1.0 60.0±1.0 60.0±1.0 60.0±1.0 13.5±0.7 13.5±0.7 13.5±0.7 13.5±0.7 13.5±0.7 9.5±0.1 9.5±0.1 9.5±0.1 13.5±1.0 13.5±1.0 11.5±1.0 11.5±1.0 11.5±1.0 15.5±1.0 15.5±1.0 5,000 5,000 5,000 - Embossed Plastic Tape (EA) 4,000 4,000 Paper Tape Specifications Type A B W E F P0 P1 P2 ΦD0 T TLM1J 1.10 ±0.10 1.60 ±0.10 1.90 ±0.10 1.90 ±0.10 2.40 ±0.20 3.50 ±0.20 8.0 ±0.20 8.0 ±0.20 8.0 ±0.20 1.75 ±0.10 1.75 ±0.10 1.75 ±0.10 3.50 ±0.05 3.50 ±0.05 3.50 ±0.05 4.00 ±0.10 4.00 ±0.10 4.00 ±0.10 4.00 ±0.05 4.00 ±0.05 4.00 ±0.05 2.00 ±0.05 2.00 ±0.05 2.00 ±0.05 1.50 +0.1 -0 1.50 +0.1 -0 1.50 +0.1 -0 0.70 ±0.10 0.85 ±0.10 0.85 ±0.10 TLM2A TLM2B 1773269-1 CIS WR 01/2015 Dimensions in millimetres unless otherwise specified Dimensions Shown for reference purposes only. Specifications subject to change For Email, phone or live chat, go to: www.te.com/help SMD Current Sense Metal Chip Resistor Embossed Plastic Tape Specifications Type A B W E F P0 P1 P2 ΦD0 T TLM2H 2.80 ±0.10 3.50 ±0.10 5.50 ±0.10 6.700 ±0.20 12.0 ±0.10 12.0 ±0.20 1.75 ±0.10 1.75 ±0.10 5.50 ±0.05 5.50 ±0.05 4.00 ±0.05 4.00 ±0.05 4.00 ±0.10 4.00 ±0.10 2.00 ±0.05 2.00 ±0.05 1.50 ±0.10 1.50 ±0.10 1.00 ±0.20 1.00 ±0.20 TLM3A How To Order TLM Common Part TLM 1773269-1 CIS WR 01/2015 2A Size 1J – 0603 2A – 0805 2B – 1206 2H – 2010 3A – 2512 Dimensions in millimetres unless otherwise specified TCR E R01 Resistance Value D – 50PPM 10mΩ - R01 E– 100PPM 100mΩ R10 Dimensions Shown for reference purposes only. Specifications subject to change J Tolerance F - 1% J - 5% TD Pack Style TD – Reel 5K (0603,0805, 1206) TE – Reel 4K (2010, 2512) For Email, phone or live chat, go to: www.te.com/help