BGA728L7

Data Sheet, Rev. 2.0, January 2009 BGA728L7 Broadband Low Noise Amplifier for Portable and Mobile TV Applications Small Signal Discretes Edition 2009-01-20 Published by Infineon Technologies AG 81726 München, Germany © Infineon Technologies AG 2009. All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics (“Beschaffenheitsgarantie”). With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. BGA728L7 BGA728L7 Revision History: 2009-01-20, Rev. 2.0 Previous Version: 2008-09-25, Rev. 1.2 Page All Subjects (major changes since last revision) Status changed from preliminary to final data sheet Data Sheet 3 Rev. 2.0, 2009-01-20 BGA728L7 Broadband Low Noise Amplifier for Portable and Mobile TV Applications 1 Broadband Low Noise Amplifier for Portable and Mobile TV Applications Features • High gain mode: 15.75 dB gain • Low gain mode: -5.2 dB gain • Noise figure: 1.3 / 5.5 dB in high / low gain mode • Power off function • Operating frequency: 100 ~ 1700 MHz • Supply voltage: 1.5 V to 3.6 V • Small leadless TSLP-7-1 package (2.0 x 1.3 x 0.4 mm³) • Output internally matched to 50 Ω • Input pre-matched to 50 Ω • Low external component count • Integrated ESD protection (1 kV HBM) • Moisture sensitivity level: MSL 1 • Pb-free (RoHS compliant) package 6 5 4 7 1 2 3 TSLP-7-1 Applications • Portable and mobile TV in VHFIII-, UHF- and L-bands • ISM applications in 100... 1700 MHz • RKE applications Figure 1 Block diagram Data Sheet 4 Rev. 2.0, 2009-01-20 BGA728L7 Description 2 Description The BGA728L7 is a low power low noise amplifier (LNA) MMIC for portable and mobile TV applications in the VHFIII-, UHF- and L-Bands. The low gain mode with much higher linearity enables this LNA to work with much lower current consumption than commonly used TV LNAs. The LNA is based upon Infineon Technologies cost effective B7HFM Silicon Germanium technology and comes into a low profile TSLP-7-1 leadless green package. This document specifies the electrical parameters, pin-out, application circuit and packaging of the chip. Type BGA728L7 Pin Definition and Function Table 1 Pin No. 1 2 3 4 5 6 7 Maximum Ratings Table 2 Parameter 1) Package TSLP-7-1 Marking AP Pin Definition and Function Symbol GS RFin BIAS PON RFout VCC GND Function High-gain / Low-gain control RF input Bias voltage Power on / off control RF output Supply voltage DC/RF ground Maximum Ratings Symbol Value -0.3... 3.6 -0.3... 0.9 -0.3... VCC+ 0.3 -0.3... VCC+ 0.3 20 10 72 150 -40... 85 -65... 150 1 Unit V V V V mA dBm mW °C °C °C kV Voltage at pin VCC Voltage at pin RF_IN Voltage at pin RF_OUT Voltage at pin PON Current into pin VCC RF input power Total power dissipation Junction temperature Ambient temperature range Storage temperature range ESD integrity HBM 2) VCC VRFIN VRFOUT VPON ICC PIN Ptot TJ TA TSTG VESD 1) All voltages refer to GND-Node. 2) According to JESD22-A114 Data Sheet 5 Rev. 2.0, 2009-01-20 BGA728L7 Electrical Characteristics Thermal resistance Table 3 Parameter 1) Thermal resistance Symbol Value Unit K/W Junction - soldering point RthJS 240 1) For calculation of RthJA please refer to Application Note Thermal Resistance 3 Electrical Characteristics DC Characteristics: TA = 25 °C ; VCC = 2.8 V, unless otherwise stated; no RF input signal Symbol Min. 1.5 5.85 0.55 5 1.5 0 25 35 5 2 3.3 0.4 Values Typ. Max. 3.6 V mA mA µA V V µA µA µA µA V V µA 2 µA 3.3 0.4 35 High Low Unit Note / Test Condition Table 4 Parameter VCC Supply current high gain mode ICCHG Supply current low gain mode ICCLG Supply current at shutdown IOFF Logic levels PON pin VPON Supply voltage Current into PON pin IPON VPon = High, VGS = Low VPon = High, VGS = High VPon = Low, VGS = High VPon = Low, VGS = Low High Low Logic levels GS pin Current into GS pin VGS IGS 1.5 0 VGS = High VGS = Low Data Sheet 6 Rev. 2.0, 2009-01-20 BGA728L7 Electrical Characteristics Table 5 Parameter Typical RF Characteristics1) High-Gain Mode: TA = 25 °C, VCC = 2.8 V, VPON = 2.8 V, VGS = 0 V Symbol Min. Values Typ. Max. 1675 15.75 1 >25 1.3 >8 >8 >1.5 -10 -10 -9 dBm dBm dBm dBm dBm dBm µs µs MHz dB dB dB dB dB dB VHFIII/UHF/L-Band US/L-Band EU 170 2) Unit Note / Test Condition Frequency Range Power Gain Power Gain Variation over Frequency Reverse Isolation Noise figure 3) FBW |S21| ∆|S21| 1/|S12| f = 470MHz f = 170 MHz-1675 MHz NF Input return loss 1/|S11| Output return loss 1/|S22| 3) Stability factor k 3) Input 1 dB compression point I IP1dB f = 470 MHz 50 Ω 50 Ω From 30 kHz to 6 GHz 3rd order input intercept point 3) IIP3 -7 -7 -3 f = 170 MHz f = 470 MHz f = 1500 MHz f = 170 MHz; 1 MHz offset f = 470 MHz; 1 MHz offset f = 1500 MHz; 1 MHz offset Settling time for Power On3) Settling time Power Off 3) tPON tPOFF 3.5 2 1) Measured on BGA728L7 application board without substracting PCB losses (unless noted otherwise) at 470 - 1675 MHz 2) 170 MHz to 240 MHz (VHF III) can be covered by adding external capacitor on input circuit (see Application Information) 3) Verify by random sampling Data Sheet 7 Rev. 2.0, 2009-01-20 BGA728L7 Electrical Characteristics Table 6 Parameter Typical RF Characteristics1) Low-Gain Mode: TA = 25 °C, VCC = 2.8 V, VPON = 2.8 V, VGS = 2.8 V Symbol Min. Values Typ. Max. 1675 -5.2 2.1 5.5 >8 >8 3 3.5 5 MHz dB dB dB dB dB dBm dBm dBm dBm dBm dBm µs µs VHFIII/UHF/L-Band US/L-Band EU 170 2) Unit Note / Test Condition Frequency Range Power Gain Power Gain Variation over Frequency Noise figure3) Input return loss Output return loss Input compression point 3) FPW |S21| ∆|S21| NF 1/|S11| 1/|S22| IP1dB f = 170 MHz-1675 MHz f = 470 MHz 50 Ω 50 Ω 3rd order input intercept point 3) IIP3 16 16 20 f = 170 MHz f = 470 MHz f = 1500 MHz f = 170 MHz; 1 MHz offset f = 470 MHz; 1 MHz offset f = 1500 MHz; 1 MHz offset Settling time GS ON3) Settling time GS OFF 3) tGSON tGSOFF 2 3.5 1) Measured on BGA728L7 application board including PCB losses (unless noted otherwise) at 470 - 1675 MHz 2) 170 MHz to 240 MHz (VHF III) can be covered by adding external capacitor on input circuit (see Application Information) 3) Verify by random sampling Gain Mode Selection Truth Table Control Voltage VPON1) High High Low Low Control Voltage VGS1) Low High High Low Gain Mode High Gain Low Gain Low Gain OFF 1) See Table 4 for the High/Low voltage range Data Sheet 8 Rev. 2.0, 2009-01-20 BGA728L7 Typical Measured Results 4 Typical Measured Results TA = 25 °C, VCC = 2.8 V , VPON = 2.8 V, VGS = 0 V for High Gain Mode, VGS = 2.8 V for Low Gain Mode Note: Measurements based on VHF-board application. For UHF application NF can be further optimized by omitting the optional capacitor C5. Note: Board losses are not substracted Gain |S21| = f (f) 20 Isolation |S12| = f (f) 0 -5 15 -10 -15 mag(S12) / dB 10 mag(S21) / dB -20 -25 -30 -35 -40 -45 High Gain Low Gain High Gain 5 Low Gain 0 -5 -10 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 -50 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 f / GHz Gain .vsd f / GHz Isolation.vsd Data Sheet 9 Rev. 2.0, 2009-01-20 BGA728L7 Typical Measured Results Input Return Loss |S11| = f (f) Output Return Loss |S22| = f (f) 0 0 -2 -4 High Gain -6 Low Gain -5 mag(S11) / dB -8 -10 -12 -14 -16 -18 -20 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 mag(S22) / dB High Gain -10 Low Gain -15 -20 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 f / GHz IRL.vsd f / GHz ORL.vsd High Gain Noise Figure NF = f (f) High Gain Stability Factor k = f (f) 2.0 50 45 40 1.5 35 30 NF / dB k 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 1.0 25 20 15 0.5 10 5 0.0 0 0.0 1.0 2.0 3.0 4.0 5.0 6.0 f / GHz NF.vsd f / GHz K _factor.vsd Data Sheet 10 Rev. 2.0, 2009-01-20 BGA728L7 Application Information 5 Application Information Application Circuit N1 1 - GS GainStep RFin, 50 Ω BGA728L7 VCC - 6 Supply RFout, 50 Ω C1 2 - RF_IN RF_OUT 5 GND 7 C4 L1 3 BIAS PON - 4 PowerOn C5 (optional ) BGA 728L 7_Blockdiagram .vsd Figure 2 Table 7 Name C1 C4 C5 L1 N1 C2, C3 Application circuit of BGA728L7 Bill of Materials Value 56 pF 1 nF 1 nF 75 nH BGA728L7 not used AN163 in particular for BGA728L7 is available at Package 0402 0402 0402 0402 TSLP-7-1 Manufacturer Various Various Various Murata LQW15AN75NG00 Infineon Function DC block Supply voltage filtering Optional for VHF-band Bias Feed SiGe LNA A list of all application notes including http://www.infineon.com/MobileTVLNA Data Sheet 11 Rev. 2.0, 2009-01-20 BGA728L7 Application Information Application Board BGA728 L7_ Application_Board .vsd Figure 3 Application Board 0.017 mm 0.100 mm 0.100 mm 0.035 mm Copper Prepreg FR4 Prepreg FR4 Copper 0.460 mm FR4 0.100 mm 0.100 mm 0.017 mm Prepreg FR4 Prepreg FR4 Copper Figure 4 Cross section View of Application board 0.2 0.2 0.2 1.4 NSMD 0.2 1.4 1.4 SMD 0.2 1.4 0.2 0.25 0.2 1.9 0.2 0.25 1.9 1.9 1.9 0.2 0.2 0.2 0.25 0.2 0.3 0.3 Copper 0.3 0.25 0.25 Stencil apertures 0.2 R0.1 0.3 0.3 Copper 0.3 0.25 0.25 Stencil apertures R0.1 Solder mask Solder mask Figure 5 Recommended Land Pattern Data Sheet 12 Rev. 2.0, 2009-01-20 0.2 0.25 BGA728L7 Package Information 6 Package Information Top view 0.4 0.05 MAX. +0.1 Bottom view 1.3 ±0.05 1 ±0.05 4 5 6 1.7 ±0.05 6 x 0.2 ±0.035 1) 7 3 Pin 1 marking 2 1 6 x 0.2 ±0.035 1) GPC09484 1) Dimension applies to plated terminal Figure 6 Package Dimensions for TSLP-7-1 4 0.5 2.18 Pin 1 marking 1.45 CPSG9506 Figure 7 Tape & Reel Dimensions (Ø reel 180, pieces/reel 7500) Figure 8 Marking Layout Data Sheet 13 8 2 ±0.05 1.2 ±0.035 1) 1.1 ±0.035 1) Rev. 2.0, 2009-01-20