TLE4268GS

5-V Low Drop Fixed Voltage Regulator TLE 4268 Features • • • • • • • • • • • • Output voltage tolerance ≤ ±2% Very low current consumption Low-drop voltage Watchdog Settable reset threshold Overtemperature protection Reverse polarity protection Short-circuit proof Suitable for use in automotive electronics Wide temperature range Green Product (RoHS compliant) AEC Qualified P-DSO-8-3, -6, -7, -8, -9 Functional Description This device is a 5-V low-drop fixed-voltage regulator. The P/PG-DSO-20-1,-6,-7,-9,-14,maximum input voltage is 45 V. It can deliver an output current of at least 180 mA. The IC is short-circuit proof and features temperature protection that disables the circuit in the event of impermissibly high temperatures. The watchdog function is disabled as a function of the load, so that a controller is not interrupted during sleep mode by a watchdog reset. Application Description The IC regulates an input voltage VI in the range 5.5 V < VI < 45 V to VQ,nom = 5.0 V. In the event of an output voltage VQ < VRT, a reset signal is generated. The wiring of the reset switching threshold input enables the value of VRT to be reduced. The reset delay time can be adjusted using an external capacitor. The integrated watchdog monitors the connected active controller. If there is no rising edge at the watchdog input, the reset Type TLE 4268 GS TLE 4268 G Data Sheet 1 Package PG-DSO-8-16 PG-DSO-20-35 Rev. 1.5, 2007-03-20 TLE 4268 output is set to low. The reset delay capacitor provides a wide adjustment range for the pulse repetition time. The watchdog function is only activated if the load exceeds 8 mA. This ensures that a microcontroller is not activated during power-down and the current drain is not increased. The IC is protected against overload and overtemperature. PG-DSO-8-16 Ι N.C. RO GND 1 2 3 4 8 7 6 5 AEP01954 Q W RADJ D Figure 1 Table 1 Pin 1 2 3 4 5 6 7 8 I Pin Configuration (top view) Pin Definitions and Functions Symbol N.C. RO GND D RADJI W Q Function Input voltage Not connected Reset output Ground Reset delay Reset switching threshold Watchdog input 5 V output voltage Data Sheet 2 Rev. 1.5, 2007-03-20 TLE 4268 PG-DSO-20-35 N.C. N.C. RO GND GND GND GND N.C. D RADJ 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 AEP01540 N.C. N.C. Ι GND GND GND GND N.C. Q W Figure 2 Table 2 Pin Pin Configuration (top view) Pin Definitions and Functions Symbol Function Not connected. Reset output; the open collector output is connected to the 5-V output via an integrated resistor of 30 kΩ. Ground Reset delay; connect a capacitor to ground for delay time adjustment. Reset switching threshold; for setting the switching threshold, output to ground with voltage divider. If this input is connected to ground, the reset is triggered at an output voltage of 4.5 V. Watchdog input; positive-edge-triggered input for monitoring a microcontroller. 5-V output voltage; block to ground with 22 µF capacitor, ESR < 3 Ω. Input voltage; block to ground directly on the IC with ceramic capacitor. 1, 2, 8, 13, N.C. 19, 20 3 4 … 7, 14 … 17 9 10 RO GND D RADJ 11 12 18 W Q I Data Sheet 3 Rev. 1.5, 2007-03-20 TLE 4268 Circuit Description The control amplifier compares a reference voltage, which is kept highly accurate by resistance adjustment, to a voltage that is proportional to the output voltage and drives the base of the series transistor via a buffer. Saturation control as a function of the load current prevents any over-saturation of the power element. If the externally scaled down output voltage at the reset threshold input drops below 1.35 V, the external reset delay capacitor is discharged by the reset generator. If the voltage on the capacitor reaches the lower threshold VDRL, a reset signal is generated on the reset output and not cancelled again until the upper threshold voltage is exceeded. If the reset threshold input is connected to GND, reset is triggered at an output voltage of 4.5 V. A connected microcontroller is monitored by the watchdog logic. If pulses are missing, the rest output is set to low. The pulse sequence time can be set within a wide range with the reset delay capacitor. The IC also incorporates internal circuits for protection against: • • • Overload Overtemperature Reverse polarity Input 18 12 Output Temperature Sensor Protection Circuit Reset Generator Control Amplifier + - 3 Reset Output Reset 10 Switching Threshold 9 Reset Delay Adjustment Bandgap Reference Watchdog 4-7, 14-17 GND 11 Watchdog Input AEB01539 Figure 3 Block Diagram TLE 4268 G (PG-DSO-20-35) Data Sheet 4 Rev. 1.5, 2007-03-20 TLE 4268 Table 3 Parameter Input I Input voltage Input current Absolute Maximum Ratings Symbol Limit Values Min. Max. 45 – 7 – 7 – 7 7 7 – 50 150 150 V – V – V – V V V – mA °C °C – Internally limited – Internally limited – Internally limited – – – Internally limited – – – Unit Notes VI II VR IR VD ID VW VRADJ VQ IQ IGND Tj TS -30 – -0.3 – -0.3 – -0.3 -0.3 -0.3 – -100 -40 -50 Reset Output RO Voltage Current Reset Delay D Voltage Current Watchdog W Watchdog input Reset threshold Output Q Output voltage Output current Ground GND Current Temperatures Junction temperature Storage temperature Reset Switching Threshold RADJ Data Sheet 5 Rev. 1.5, 2007-03-20 TLE 4268 Table 4 Parameter Input voltage Operating Range Symbol Limit Values Min. Max. 45 150 185 100 72 23 V °C K/W K/W K/W K/W – – PG-DSO-8-161) PG-DSO-20-351) PG-DSO-8-162) PG-DSO-20-353) – -40 – – – – Unit Notes Junction temperature Thermal Resistance Junction ambient (soldered) Junction pin VI Tj Rthj-a Rthj-a Rthj-pin Rthj-pin 1) Package mounted on PCB 80 × 80 × 1.5 mm3; 35µ Cu; 5µ Sn; Footprint only; zero airflow. 2) Measured to pin 2. 3) Measured to pin 5. Optimum reliability and life time are guaranteed if the junction temperature does not exceed 125 °C in operating mode. Operation at up to the maximum junction temperature of 150 °C is possible in principle. Note, however, operation at the maximum permitted ratings could affect the reliability of the device. Data Sheet 6 Rev. 1.5, 2007-03-20 TLE 4268 Table 5 Characteristics VI = 13.5 V; -40 °C ≤ Tj ≤ 125 °C (unless otherwise specified) Parameter Output voltage Symbol Min. Limit Values Typ. 5.00 250 300 13 0.25 10 10 Max. 5.10 – 450 20 0.50 30 30 V mA µA mA V mV mV 5 mA ≤ IQ ≤ 150 mA; 6 V ≤ VI ≤ 28 V – 4.90 180 – – – – – Unit Test Condition VQ Output current limiting IQ Current consumption Iq = II - IQ Current consumption Iq = II - IQ Drop voltage Load regulation Line regulation Reset Generator Reset threshold Reset adjust threshold Reset low voltage Saturation voltage Charging current Upper reset timing threshold Reset delay time Reset reaction time Pull-up Lower reset timing threshold Iq Iq VDR ∆VQ,Lo ∆VQ,Li IQ = 0 m A IQ = 150 mA IQ = 150 mA1) IQ = 5 to 150 mA VI = 6 to 28 V IQ = 150 mA – – 1 mA external VQ,rt VRADJ VRO,l VD ID,c VDU trd trr RRO VDRL 4.2 1.28 – – 5 1.4 10 – 18 0.2 4.5 1.35 0.2 30 12 1.8 15 2 30 0.4 4.8 1.45 0.5 100 18 2.2 25 – 46 0.55 V V V mV µA V ms µs kΩ V VQ < VRT VD = 1.0 V – CD = 100 nF CD = 100 nF with resp. to VQ – Data Sheet 7 Rev. 1.5, 2007-03-20 TLE 4268 Table 5 Characteristics (cont’d) VI = 13.5 V; -40 °C ≤ Tj ≤ 125 °C (unless otherwise specified) Parameter Watchdog Discharge current Charging current Upper timing threshold Lower timing threshold Watchdog period Symbol Min. Limit Values Typ. 3.5 12 1.8 0.4 55 40 8 – Max. 5.2 18 2.2 0.55 75 60 15 – µA µA V V ms ms mA Unit Test Condition ID,d ID,c VDU VDWL 1.5 5 1.4 0.2 30 25 2 5 VD = 1.0 V VD = 1.0 V – – TWP Watchdog trigger time TWT IQ Activating current Slew rate dVW/dt CD = 100 nF CD = 100 nF Activates watchdog V/µs from 20% up to 80% VQ2) 1) Drop voltage = VI - VQ (measured when the output voltage has dropped 100 mV from the nominal value obtained at 13.5 V input) 2) Watchdog pulse recognition tested with 10 kHz max. pulse frequency Note: The reset output is low in range from VQ = 1 V to VQ,rt. Data Sheet 8 Rev. 1.5, 2007-03-20 TLE 4268 ΙΙ 1000 µ F 470 nF Ι Q ΙQ 22 µF TLE 4268G VΙ W D VW VD RO RADJ VRES ΙR VQ VR GND Ι dis Ιd CD 100 nF ΙM AES01541 VDr = VΙ -VQ Outside the control range Figure 4 Test Circuit Data Sheet 9 Rev. 1.5, 2007-03-20 TLE 4268 Reset Timing The power-on reset delay time is defined by the charging time of an external capacitor CD which can be calculated as follows: CD = (∆trd × ID,c)/∆V Definitions: • • • • • (1) LOW after the output voltage has dropped below the reset threshold. It is typically 1 µs for delay capacitor of 47 nF. For other values for CD the reaction time can be estimated using the following equation: CD = delay capacitor ∆trd = delay time ID,c = charge current, typical 12 µA ∆V = VDU, typical 1.8 V VDU = upper delay switching threshold at CD for reset delay time The reset reaction time trr is the time it takes the voltage regulator to set the reset out trr ≈ 20 s/F × CD (2) VΙ VQ < t rr V Q, rt d V Ι D,c = dt CD t t V DU V DRL VD VRO t rd t rr t t Power-on-Reset Thermal Shutdown Voltage Dip at Input Undervoltage Secondary Spike Overload at Output AED03010 Figure 5 Timing (Watchdog disabled) Data Sheet 10 Rev. 1.5, 2007-03-20 TLE 4268 VW Ι VΙ t VQ T WP t VD VDU VDWL VWO T WT t t WD, L t T WT = (VDU - VDWL ) Ι D, d C D ; T WP = (VDU - VDWL ) (Ι D, c + Ι D, d ) Ι D, c x Ι D, d C D ; t WD, L = (VDU - VDWL ) t Ι D, c CD AED03011_68 Figure 6 Timing of the Watchdog Function Data Sheet 11 Rev. 1.5, 2007-03-20 TLE 4268 Drop Voltage VDR versus Output Current IQ mV V dr 700 600 500 400 Tj = 125 C 300 Tj = 25 C 200 100 0 AED01544 Current Consumption Iq versus Output Current IQ 16 I q mA 14 12 10 8 6 4 2 0 AED01545 VI = 13.5 V Tj = 25 ˚C 0 50 100 150 200 250 mA 0 50 100 150 mA 200 ΙQ IQ Current Consumption Iq versus Input Voltage VI 24 AED01546 Output Voltage versus Input Voltage VI mA VQ 10 AED01547 Iq mA 20 Tj = 25 ˚C 16 R L= 33 Ω 12 8 6 R L= 33 Ω 8 4 R L= 50 Ω 4 R L= 100 Ω 0 10 20 30 40 V 50 2 0 0 0 2 4 6 8 VΙ V VI Data Sheet 12 Rev. 1.5, 2007-03-20 TLE 4268 Charge Current ID,c and Discharge Current ID,d versus Temperature Tj Ι 16 µA 14 12 10 8 6 4 AED3100 Timing Threshold VDU, VDWL, VDRL versus Temperature Tj V VD 2.8 V Ι = 13.5 V 2.4 2.0 1.6 1.2 0.8 V DU AED03101 VΙ = 13.5 V VD = 1.0 V Ι D, c Ι D, d 2 0 -40 0.4 0 -40 V DWL , V DRL 0 40 80 120 Tj C 0 40 80 120 Tj C Output Voltage VQ versus Temperature Tj V VQ 5.1 VΙ = 13.5 V 5.0 AED03102 Output Current IQ versus Input Voltage VI 300 AED01551 IQ mA 250 Tj = 25 ˚C 200 4.9 150 4.8 100 4.7 50 4.6 -40 0 40 80 120 Tj V 0 0 10 20 30 40 V 50 VI Data Sheet 13 Rev. 1.5, 2007-03-20 TLE 4268 Package Outlines 0.35 x 45° 1.75 MAX. 0.175 ±0.07 (1.45) 4 -0.21) 0.19 +0.0 6 1.27 0.41 +0.1 -0.06 8 5 0.1 B 6 ±0.2 0.64 ±0.25 0.2 M A B 8x Index Marking 1 4 5 -0.21) A 1) Does not include plastic or metal protrusion of 0.15 max. per side 2) Lead width can be 0.61 max. in dambar area GPS01229 Figure 7 PG-DSO-8-16 (Plastic Dual Small Outline) Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). You can find all of our packages, sorts of packing and others in our Infineon Internet Page “Products”: http://www.infineon.com/products. SMD = Surface Mounted Device Data Sheet 14 Dimensions in mm Rev. 1.5, 2007-03-20 8° MAX. TLE 4268 2.65 MAX. 0.35 x 45˚ 7.6 -0.2 1) 2.45 -0.2 0.2 -0.1 1.27 0.35 +0.15 2) 0.4 +0.8 10.3 ±0.3 0.1 20x 0.2 20x 20 11 1 10 12.8 -0.2 1) Index Marking 1) Does not include plastic or metal protrusion of 0.15 max. per side 2) Does not include dambar protrusion of 0.05 max. per side GPS05094 Figure 8 PG-DSO-20-35 (Plastic Dual Small Outline) Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). You can find all of our packages, sorts of packing and others in our Infineon Internet Page “Products”: http://www.infineon.com/products. SMD = Surface Mounted Device Data Sheet 15 Dimensions in mm Rev. 1.5, 2007-03-20 0.23 +0.09 8˚ MAX. TLE 4268 Version Rev. 1.5 Date Changes 2007-03-20 Initial version of RoHS-compliant derivate of TLE 4268 Page 1: AEC certified statement added Page 1 and Page 14 ff: RoHS compliance statement and Green product feature added Page 1 and Page 14 ff: Package changed to RoHS compliant version Legal Disclaimer updated Data Sheet 16 Rev. 1.5, 2007-03-20 Edition 2007-03-20 Published by Infineon Technologies AG 81726 Munich, Germany © 2007 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered.