HA5022

P CT U CT ODU E PR E PR O D ET OL UT O B S U B S TI T 5 24 E S Sheet IBL Data FA1 H O SS ® HA5022 May 2003 FN3392.7 Dual, 125MHz, Video Current Feedback Amplifier with Disable The HA5022 is a dual version of the popular Intersil HA5020. It features wide bandwidth and high slew rate, and is optimized for video applications and gains between 1 and 10. It is a current feedback amplifier and thus yields less bandwidth degradation at high closed loop gains than voltage feedback amplifiers. The low differential gain and phase, 0.1dB gain flatness, and ability to drive two back terminated 75Ω cables, make this amplifier ideal for demanding video applications. The HA5022 also features a disable function that significantly reduces supply current while forcing the output to a true high impedance state. This functionality allows 2:1 video multiplexers to be implemented with a single IC. The current feedback design allows the user to take advantage of the amplifier’s bandwidth dependency on the feedback resistor. By reducing RF , the bandwidth can be increased to compensate for decreases at higher closed loop gains or heavy output loads. Features • Dual Version of HA-5020 • Individual Output Enable/Disable • Input Offset Voltage . . . . . . . . . . . . . . . . . . . . . . . . .800µV • Wide Unity Gain Bandwidth . . . . . . . . . . . . . . . . . 125MHz • Slew Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475V/µs • Differential Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.03% • Differential Phase. . . . . . . . . . . . . . . . . . . . . 0.03 Degrees • Supply Current (per Amplifier) . . . . . . . . . . . . . . . . 7.5mA • ESD Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4000V • Guaranteed Specifications at ±5V Supplies Applications • Video Multiplexers; Video Switching and Routing • Video Gain Block • Video Distribution Amplifier/RGB Amplifier • Flash A/D Driver • Current to Voltage Converter Part Number Information PART NUMBER HA5022IP HA5022IB HA5022EVAL TEMP. RANGE (oC) -40 to 85 -40 to 85 PACKAGE 16 Ld PDIP 16 Ld SOIC PKG. NO. E16.3 M16.15 • Medical Imaging • Radar and Imaging Systems Pinout HA5022 (PDIP, SOIC) TOP VIEW High Speed Op Amp DIP Evaluation Board -IN1 +IN1 DIS1 1 2 3 + - 16 OUT1 15 NC 14 NC 13 V+ 12 NC V- 4 DIS2 +IN2 -IN2 NC 5 6 7 8 + 11 NC 10 OUT2 9 NC - 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2003. All Rights Reserved All other trademarks mentioned are the property of their respective owners. HA5022 Absolute Maximum Ratings Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . 36V DC Input Voltage (Note 3) . . . . . . . . . . . . . . . . . . . . . . . . ±VSUPPLY Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10V Output Current (Note 4) . . . . . . . . . . . . . . . . . Short Circuit Protected ESD Rating (Note 3) Human Body Model (Per MIL-STD-883 Method 3015.7) . . 2000V Thermal Information Thermal Resistance (Typical, Note 2) θJA (oC/W) Operating Conditions Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC Supply Voltage Range (Typical) . . . . . . . . . . . . . . . . ±4.5V to ±15V PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 Maximum Junction Temperature (Note 1) . . . . . . . . . . . . . . . . .175oC Maximum Junction Temperature (Plastic Package, Note 1) . .150oC Maximum Storage Temperature Range . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only) CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Maximum power dissipation, including output load, must be designed to maintain junction temperature below 175oC for die, and below 150oC for plastic packages. See Application Information section for safe operating area information. 2. θJA is measured with the component mounted on an evaluation PC board in free air. 3. The non-inverting input of unused amplifiers must be connected to GND. 4. Output is protected for short circuits to ground. Brief short circuits to ground will not degrade reliability, however, continuous (100% duty cycle) output current should not exceed 15mA for maximum reliability. Electrical Specifications VSUPPLY = ±5V, RF = 1kΩ , AV = +1, RL = 400Ω, CL ≤ 10pF, Unless Otherwise Specified TEST CONDITIONS (NOTE 11) TEST LEVEL TEMP. (oC) PARAMETER INPUT CHARACTERISTICS Input Offset Voltage (VIO) MIN TYP MAX UNITS A A 25 Full Full Full 25 Full 25 Full Full 25 Full 25 Full 25 Full 25, 85 -40 25, 85 -40 25 Full 53 50 60 55 ±2.5 - 0.8 1.2 5 3 4 10 6 10 - 3 5 3.5 8 20 0.15 0.5 0.1 0.3 12 30 15 30 0.4 1.0 mV mV mV µV/oC dB dB dB dB V µA µA µA/V µA/V µA/V µA/V µA µA µA µA µA/V µA/V Delta VIO Between Channels Average Input Offset Voltage Drift VIO Common Mode Rejection Ratio Note 5 A B A A VIO Power Supply Rejection Ratio ±3.5V ≤ VS ≤ ±6.5V A A Input Common Mode Range Non-Inverting Input (+IN) Current Note 5 A A A +IN Common Mode Rejection (+IBCMR = 1 ) +RIN +IN Power Supply Rejection Note 5 A A ±3.5V ≤ VS ≤ ±6.5V A A Inverting Input (-IN) Current A A Delta -IN BIAS Current Between Channels -IN Common Mode Rejection Note 5 A A A A 2 HA5022 Electrical Specifications VSUPPLY = ±5V, RF = 1kΩ , AV = +1, RL = 400Ω, CL ≤ 10pF, Unless Otherwise Specified (Continued) TEST CONDITIONS ±3.5V ≤ VS ≤ ±6.5V (NOTE 11) TEST LEVEL A A Input Noise Voltage +Input Noise Current -Input Noise Current TRANSFER CHARACTERISTICS Transimpedance Note 16 A A Open Loop DC Voltage Gain RL = 400Ω, VOUT = ±2.5V A A Open Loop DC Voltage Gain RL = 100Ω, VOUT = ±2.5V A A OUTPUT CHARACTERISTICS Output Voltage Swing RL = 150Ω A A Output Current Output Current, Short Circuit Output Current, Disabled Output Disable Time Output Enable Time Output Capacitance, Disabled RL = 150Ω VIN = ±2.5V, VOUT = 0V VOUT = ±2.5V, VIN = 0V, DISABLE = 0V Note 12 Note 13 Note 14 B A A B B B 25 Full Full Full Full 25 25 25 ±2.5 ±2.5 ±16.6 ±40 ±3.0 ±3.0 ±20.0 ±60 40 40 15 2 V V mA mA µA µs ns pF 25 Full 25 Full 25 Full 1.0 0.85 70 65 50 45 MΩ MΩ dB dB dB dB f = 1kHz f = 1kHz f = 1kHz B B B TEMP. (oC) 25 Full 25 25 25 PARAMETER -IN Power Supply Rejection MIN - TYP 4.5 2.5 25.0 MAX 0.2 0.5 - UNITS µA/V µA/V nV/√Hz pA/√Hz pA/√Hz POWER SUPPLY CHARACTERISTICS Supply Voltage Range Quiescent Supply Current Supply Current, Disabled Disable Pin Input Current Minimum Pin 8 Current to Disable Maximum Pin 8 Current to Enable AC CHARACTERISTICS (AV = +1) Slew Rate Full Power Bandwidth Rise Time Fall Time Propagation Delay Overshoot -3dB Bandwidth Settling Time to 1% Settling Time to 0.25% VOUT = 100mV 2V Output Step 2V Output Step Note 8 Note 9 Note 10 Note 10 Note 10 B B B B B B B B B 25 25 25 25 25 25 25 25 25 275 22 400 28 6 6 6 4.5 125 50 75 V/µs MHz ns ns ns % MHz ns ns DISABLE = 0V DISABLE = 0V Note 6 Note 7 A A A A A A 25 Full Full Full Full Full 5 350 7.5 5 1.0 15 10 7.5 1.5 20 V mA/Op Amp mA/Op Amp mA µA µA 3 HA5022 Electrical Specifications VSUPPLY = ±5V, RF = 1kΩ , AV = +1, RL = 400Ω, CL ≤ 10pF, Unless Otherwise Specified (Continued) TEST CONDITIONS (NOTE 11) TEST LEVEL TEMP. (oC) PARAMETER MIN TYP MAX UNITS AC CHARACTERISTICS (AV = +2, RF = 681Ω) Slew Rate Full Power Bandwidth Rise Time Fall Time Propagation Delay Overshoot -3dB Bandwidth Settling Time to 1% Settling Time to 0.25% Gain Flatness VOUT = 100mV 2V Output Step 2V Output Step 5MHz 20MHz AC CHARACTERISTICS (AV = +10, RF = 383Ω) Slew Rate Full Power Bandwidth Rise Time Fall Time Propagation Delay Overshoot -3dB Bandwidth Settling Time to 1% Settling Time to 0.1% VIDEO CHARACTERISTICS Differential Gain (Note 15) Differential Phase (Note 15) NOTES: 5. VCM = ±2.5V. At -40oC Product is tested at VCM = ±2.25V because short test duration does not allow self heating. 6. RL = 100Ω, VIN = 2.5V. This is the minimum current which must be pulled out of the Disable pin in order to disable the output. The output is considered disabled when -10mV ≤ VOUT ≤ +10mV. 7. VIN = 0V. This is the maximum current that can be pulled out of the Disable pin with the HA5022 remaining enabled. The HA5022 is considered disabled when the supply current has decreased by at least 0.5mA. 8. VOUT switches from -2V to +2V, or from +2V to -2V. Specification is from the 25% to 75% points. Slew Rate9. FPBW = ---------------------------- ; V = 2 V. 2 π V PEAK PEAK 10. RL = 100Ω, VOUT = 1V. Measured from 10% to 90% points for rise/fall times; from 50% points of input and output for propagation delay. 11. A. Production Tested; B. Typical or Guaranteed Limit based on characterization; C. Design Typical for information only. 12. VIN = +2V, DISABLE = +5V to 0V. Measured from the 50% point of DISABLE to VOUT = 0V. 13. VIN = +2V, DISABLE = 0V to +5V. Measured from the 50% point of DISABLE to VOUT = 2V. 14. VIN = 0V, Force VOUT from 0V to ±2.5V, tR = tF = 50ns, DISABLE = 0V. 15. Measured with a VM700A video tester using an NTC-7 composite VITS. 16. VOUT = ±2.5V. At -40oC Product is tested at VOUT = ±2.25V because short test duration does not allow self heating. RL = 150Ω RL = 150Ω B B 25 25 0.03 0.03 % Degrees VOUT = 100mV 2V Output Step 2V Output Step Note 8 Note 9 Note 10 Note 10 Note 10 B B B B B B B B B 25 25 25 25 25 25 25 25 25 350 28 475 38 8 9 9 1.8 65 75 130 V/µs MHz ns ns ns % MHz ns ns Note 8 Note 9 Note 10 Note 10 Note 10 B B B B B B B B B B B 25 25 25 25 25 25 25 25 25 25 25 475 26 6 6 6 12 95 50 100 0.02 0.07 V/µs MHz ns ns ns % MHz ns ns dB dB 4 HA5022 Test Circuits and Waveforms + DUT 50Ω HP4195 NETWORK ANALYZER 50Ω FIGURE 1. TEST CIRCUIT FOR TRANSIMPEDANCE MEASUREMENTS (NOTE 17) 100Ω + 50Ω RF , 1kΩ DUT VOUT RL 100Ω VIN 50Ω RI 681Ω + (NOTE 17) 100Ω VIN DUT VOUT RL 400Ω - - RF , 681Ω FIGURE 2. SMALL SIGNAL PULSE RESPONSE CIRCUIT NOTE: FIGURE 3. LARGE SIGNAL PULSE RESPONSE CIRCUIT 17. A series input resistor of ≥100Ω is recommended to limit input currents in case input signals are present before the HA5022 is powered up. Vertical Scale: VIN = 100mV/Div., VOUT = 100mV/Div. Horizontal Scale: 20ns/Div. Vertical Scale: VIN = 1V/Div., VOUT = 1V/Div. Horizontal Scale: 50ns/Div. FIGURE 4. SMALL SIGNAL RESPONSE FIGURE 5. LARGE SIGNAL RESPONSE 5 Schematic Diagram V+ R2 800 (One Amplifier of Two) R5 2.5K R6 15K D2 R10 820 QP8 QP9 QP11 R15 400 R19 400 QP14 R17 280 R18 280 R27 200 R33 2K QP18 QP19 R29 9.5 QP1 QN5 QP5 R11 1K R31 5 R24 140 R20 140 QP16 QP20 6 R8 1.25K QN8 QP2 R1 60K QN1 R7 15K DIS R3 6K QP3 QN6 QP6 R12 280 +IN QP4 QN2 QN10 D1 QN4 QN3 QP7 QN7 R13 1K R4 800 VR33 800 R9 820 QN9 QN11 QP10 QN12 C1 1.4pF QP12 -IN QN13 QP13 QP15 R28 20 QP17 QN17 HA5022 C2 1.4pF R25 20 QN15 R21 140 QN21 R32 5 QN20 R26 200 QN19 R30 7 OUT R14 280 QN14 R22 280 R25 140 QN16 QN18 R16 400 R23 400 R26 200 HA5022 Application Information Optimum Feedback Resistor The plots of inverting and non-inverting frequency response, see Figure 11 and Figure 12 in the Typical Performance Curves section, illustrate the performance of the HA5022 in various closed loop gain configurations. Although the bandwidth dependency on closed loop gain isn’t as severe as that of a voltage feedback amplifier, there can be an appreciable decrease in bandwidth at higher gains. This decrease may be minimized by taking advantage of the current feedback amplifier’s unique relationship between bandwidth and RF . All current feedback amplifiers require a feedback resistor, even for unity gain applications, and RF , in conjunction with the internal compensation capacitor, sets the dominant pole of the frequency response. Thus, the amplifier’s bandwidth is inversely proportional to RF . The HA5022 design is optimized for a 1000Ω RF at a gain of +1. Decreasing RF in a unity gain application decreases stability, resulting in excessive peaking and overshoot. At higher gains the amplifier is more stable, so RF can be decreased in a trade-off of stability for bandwidth. The table below lists recommended RF values for various gains, and the expected bandwidth. GAIN (ACL) -1 +1 +2 +5 +10 -10 RF (Ω) 750 1000 681 1000 383 750 BANDWIDTH (MHz) 100 125 95 52 65 22 as short as possible to minimize the capacitance from this node to ground. Driving Capacitive Loads Capacitive loads will degrade the amplifier’s phase margin resulting in frequency response peaking and possible oscillations. In most cases the oscillation can be avoided by placing an isolation resistor (R) in series with the output as shown in Figure 6. 100Ω VIN RT RF RI + R VOUT CL - FIGURE 6. PLACEMENT OF THE OUTPUT ISOLATION RESISTOR, R The selection criteria for the isolation resistor is highly dependent on the load, but 27Ω has been determined to be a good starting value. Power Dissipation Considerations Due to the high supply current inherent in dual amplifiers, care must be taken to insure that the maximum junction temperature (TJ, see Absolute Maximum Ratings) is not exceeded. Figure 7 shows the maximum ambient temperature versus supply voltage for the available package styles (PDIP, SOIC). At VS = ±5V quiescent operation both package styles may be operated over the full industrial range of -40oC to 85oC. It is recommended that thermal calculations, which take into account output power, be performed by the designer. 140 MAX. AMBIENT TEMPERATURE 130 120 110 100 90 80 5 7 9 11 13 15 SUPPLY VOLTAGE (±V) SOIC PDIP PC Board Layout The frequency response of this amplifier depends greatly on the amount of care taken in designing the PC board. The use of low inductance components such as chip resistors and chip capacitors is strongly recommended. If leaded components are used the leads must be kept short especially for the power supply decoupling components and those components connected to the inverting input. Attention must be given to decoupling the power supplies. A large value (10µF) tantalum or electrolytic capacitor in parallel with a small value (0.1µF) chip capacitor works well in most cases. A ground plane is strongly recommended to control noise. Care must also be taken to minimize the capacitance to ground seen by the amplifier’s inverting input (-IN). The larger this capacitance, the worse the gain peaking, resulting in pulse overshoot and possible instability. It is recommended that the ground plane be removed under traces connected to -IN, and that connections to -IN be kept FIGURE 7. MAXIMUM OPERATING AMBIENT TEMPERATURE vs SUPPLY VOLTAGE Enable/Disable Function When enabled the amplifier functions as a normal current feedback amplifier with all of the data in the electrical specifications table being valid and applicable. When 7 HA5022 disabled the amplifier output assumes a true high impedance state and the supply current is reduced significantly. The circuit shown in Figure 8 is a simplified schematic of the enable/disable function. The large value resistors in series with the DISABLE pin makes it appear as a current source to the driver. When the driver pulls this pin low current flows out of the pin and into the driver. This current, which may be as large as 350µA when external circuit and process variables are at their extremes, is required to insure that point “A” achieves the proper potential to disable the output. The driver must have the compliance and capability of sinking all of this current. V+ R6 15K D1 R7 15K ENABLE/DISABLE INPUT R8 QP3 R33 QP18 A position 1. At position 1 the switch pulls the disable pin up to the plus supply rail thereby enabling the amplifier. Since all of the actual signal switching takes place within the amplifier, it’s differential gain and phase parameters, which are 0.03% and 0.03 degrees respectively, determine the circuit’s performance. The other circuit, U1B, operates in a similar manner. When the plus supply rail is 5V the disable pin can be driven by a dedicated TTL gate as discussed earlier. If a multiplexer IC or its equivalent is used to select channels its logic must be break before make. When these conditions are satisfied the HA5022 is often used as a remote video multiplexer, and the multiplexer may be extended by adding more amplifier ICs. Low Impedance Multiplexer Two common problems surface when you try to multiplex multiple high speed signals into a low impedance source such as an A/D converter. The first problem is the low source impedance which tends to make amplifiers oscillate and causes gain errors. The second problem is the multiplexer which supplies no gain, introduces all kinds of distortion and limits the frequency response. Using op amps which have an enable/disable function, such as the HA5022, eliminates the multiplexer problems because the external mux chip is not needed, and the HA5022 can drive low impedance (large capacitance) loads if a series isolation resistor is used. Referring to Figure 10, both inputs are terminated in their characteristic impedance; 75Ω is typical for video applications. Since the drivers usually are terminated in their characteristic impedance the input gain is 0.5, thus the amplifiers, U2, are configured in a gain of +2 to set the circuit gain equal to one. Resistors R2 and R3 determine the amplifier gain, and if a different gain is desired R2 should be changed according to the equation G = (1 + R3/R2). R3 sets the frequency response of the amplifier so you should refer to the manufacturers data sheet before changing its value. R5, C1 and D1 are an asymmetrical charge/discharge time circuit which configures U1 as a break before make switch to prevent both amplifiers from being active simultaneously. If this design is extended to more channels the drive logic must be designed to be break before make. R4 is enclosed in the feedback loop of the amplifier so that the large open loop amplifier gain of U2 will present the load with a small closed loop output impedance while keeping the amplifier stable for all values of load capacitance. The circuit shown in Figure 10 was tested for the full range of capacitor values with no oscillations being observed; thus, problem one has been solved.The frequency and gain characteristics of the circuit are now those of the amplifier independent of any multiplexing action; thus, problem two has been solved. The multiplexer transition time is approximately 15µs with the component values shown. R10 FIGURE 8. SIMPLIFIED SCHEMATIC OF ENABLE/DISABLE FUNCTION When VCC is +5V the DISABLE pin may be driven with a dedicated TTL gate. The maximum low level output voltage of the TTL gate, 0.4V, has enough compliance to insure that the amplifier will always be disabled even though D1 will not turn on, and the TTL gate will sink enough current to keep point “A” at its proper voltage. When VCC is greater than +5V the DISABLE pin should be driven with an open collector device that has a breakdown rating greater than VCC . Referring to Figure 8, it can be seen that R6 will act as a pullup resistor to +VCC if the DISABLE pin is left open. In those cases where the enable/disable function is not required on all circuits some circuits can be permanently enabled by letting the DISABLE pin float. If a driver is used to set the enable/disable level, be sure that the driver does not sink more than 20µA when the DISABLE pin is at a high level. TTL gates, especially CMOS versions, do not violate this criteria so it is permissible to control the enable/disable function with TTL. Typical Applications Two Channel Video Multiplexer Referring to the amplifier U1A in Figure 9, R1 terminates the cable in its characteristic impedance of 75Ω, and R4 back terminates the cable in its characteristic impedance. The amplifier is set up in a gain configuration of +2 to yield an overall network gain of +1 when driving a double terminated cable. The value of R3 can be changed if a different network gain is desired. R5 holds the disable pin at ground thus inhibiting the amplifier until the switch, S1, is thrown to 8 HA5022 (NOTE 17) U 100Ω 1 1A + 16 R1 75 R3 681 2 R4 75 VIDEO INPUT #1 - VIDEO OUTPUT TO 75Ω LOAD 3 R2 681 R5 2000 1 2 R9 75 3 ALL OFF R10 2000 S1 R11 100 +5V VIDEO INPUT #2 R6 75 (NOTE 17) U 100Ω 7 1B 10 6+ 5 R7 681 R8 681 +5V IN 0.1µF + 10µF +5V -5V IN 0.1µF + -5V 10µF NOTES: 18. U1 is HA5022. 19. All resistors in Ω. 20. S1 is break before make. 21. Use ground plane. FIGURE 9. TWO CHANNEL HIGH IMPEDANCE MULTIPLEXER R3A 681 R1A 75 INPUT A R1B 75 D1A 1N4148 R5A 2000 R2B 681 R4A U2A 27 16 1+ 4 -5V 100Ω 2 3 (NOTE 17) 0.01µF R1A 681 INPUT B U1C R3B 681 7 U2B - 10 6 + 13 5 R4B 27 OUTPUT +5V CHANNEL SWITCH C1A 0.047µF 100Ω (NOTE 17) R5B 2000 INHIBIT U1A R6 100K U1B U1D 0.01µF D1B 1N4148 C1B 0.047µF NOTES: 22. U2: HA5022. 23. U1: CD4011. FIGURE 10. LOW IMPEDANCE MULTIPLEXER 9 HA5022 Typical Performance Curves 5 4 3 NORMALIZED GAIN (dB) 2 1 0 -1 -2 -3 -4 -5 2 10 FREQUENCY (MHz) 100 200 AV = 10, RF = 383Ω VOUT = 0.2VP-P CL = 10pF AV = 2, RF = 681Ω AV = 5, RF = 1kΩ NORMALIZED GAIN (dB) AV = +1, RF = 1kΩ VSUPPLY = ±5V, AV = +1, RF = 1kΩ , RL = 400Ω, TA = 25oC, Unless Otherwise Specified 5 4 3 2 1 0 -1 -2 -3 A V = -5 -4 -5 2 10 FREQUENCY (MHz) 100 200 AV = -10 VOUT = 0.2VP-P CL = 10pF RF = 750Ω AV = -1 AV = -2 FIGURE 11. NON-INVERTING FREQUENCY RESPONSE -3dB BANDWIDTH (MHz) FIGURE 12. INVERTING FREQUENCY RESPONSE 140 VOUT = 0.2VP-P CL = 10pF A V = +1 NONINVERTING PHASE (DEGREES) -45 -90 -135 -100 -225 -270 -315 -360 2 VOUT = 0.2VP-P CL = 10pF 10 FREQUENCY (MHz) 100 AV = -10, RF = 750Ω AV = -1, RF = 750Ω AV = +10, RF = 383Ω 135 90 45 0 -45 -90 -135 -180 200 INVERTING PHASE (DEGREES) 0 AV = +1, RF = 1kΩ 180 130 5 GAIN PEAKING 500 700 900 1100 1300 FEEDBACK RESISTOR (Ω) 0 1500 FIGURE 13. PHASE RESPONSE AS A FUNCTION OF FREQUENCY -3dB BANDWIDTH (MHz) 100 VOUT = 0.2VP-P CL = 10pF A V = +2 95 FIGURE 14. BANDWIDTH AND GAIN PEAKING vs FEEDBACK RESISTANCE 130 -3dB BANDWIDTH (MHz) 120 -3dB BANDWIDTH 110 6 GAIN PEAKING (dB) -3dB BANDWIDTH GAIN PEAKING (dB) 90 10 100 4 5 90 GAIN PEAKING GAIN PEAKING 350 500 650 800 950 0 1100 VOUT = 0.2VP-P CL = 10pF A V = +1 800 2 80 0 200 400 600 LOAD RESISTOR (Ω) 0 1000 FEEDBACK RESISTOR (Ω) FIGURE 15. BANDWIDTH AND GAIN PEAKING vs FEEDBACK RESISTANCE FIGURE 16. BANDWIDTH AND GAIN PEAKING vs LOAD RESISTANCE 10 GAIN PEAKING (dB) 120 -3dB BANDWIDTH 10 HA5022 Typical Performance Curves 80 VOUT = 0.2VP-P CL = 10pF AV = +10 -3dB BANDWIDTH (MHz) 60 OVERSHOOT (%) 12 VSUPPLY = ±5V, AV = +1, RF = 1kΩ , RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued) 16 VOUT = 0.1VP-P CL = 10pF VSUPPLY = ±5V, AV = +2 40 6 VSUPPLY = ±15V, AV = +2 VSUPPLY = ±5V, AV = +1 VSUPPLY = ±15V, AV = +1 20 0 200 350 500 650 800 950 FEEDBACK RESISTOR (Ω) 0 0 200 400 600 800 1000 LOAD RESISTANCE (Ω) FIGURE 17. BANDWIDTH vs FEEDBACK RESISTANCE FIGURE 18. SMALL SIGNAL OVERSHOOT vs LOAD RESISTANCE 0.08 0.10 FREQUENCY = 3.58MHz 0.08 RL = 75Ω DIFFERENTIAL PHASE (DEGREES) FREQUENCY = 3.58MHz DIFFERENTIAL GAIN (%) 0.06 0.06 RL = 150Ω 0.04 RL = 150Ω RL = 75Ω 0.04 0.02 RL = 1k Ω 0.00 0.02 RL = 1kΩ 0.00 3 5 7 9 11 SUPPLY VOLTAGE (±V) 13 15 3 5 7 9 11 SUPPLY VOLTAGE (±V) 13 15 FIGURE 19. DIFFERENTIAL GAIN vs SUPPLY VOLTAGE -40 VOUT = 2.0VP-P CL = 30pF -50 DISTORTION (dBc) HD2 -60 3RD ORDER IMD -70 HD2 HD3 -80 HD3 -90 0.3 1 FREQUENCY (MHz) 10 FIGURE 20. DIFFERENTIAL PHASE vs SUPPLY VOLTAGE 0 -10 REJECTION RATIO (dB) -20 -30 -40 -50 -60 -70 -80 0.001 A V = +1 CMRR NEGATIVE PSRR POSITIVE PSRR 0.01 0.1 FREQUENCY (MHz) 1 10 30 FIGURE 21. DISTORTION vs FREQUENCY FIGURE 22. REJECTION RATIOS vs FREQUENCY 11 HA5022 Typical Performance Curves 8.0 RL = 100Ω VOUT = 1.0VP-P AV = + 1 PROPAGATION DELAY (ns) 10 AV = +10, RF = 383Ω VSUPPLY = ±5V, AV = +1, RF = 1kΩ , RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued) 12 RLOAD = 100Ω VOUT = 1.0VP-P PROPAGATION DELAY (ns) 7.5 7.0 8 AV = +2, RF = 681Ω 6 AV = +1, RF =1kΩ 6.5 6.0 -50 -25 0 25 50 75 TEMPERATURE (oC) 100 125 4 3 5 7 9 11 SUPPLY VOLTAGE (±V) 13 15 FIGURE 23. PROPAGATION DELAY vs TEMPERATURE FIGURE 24. PROPAGATION DELAY vs SUPPLY VOLTAGE 500 VOUT = 2VP-P 450 400 SLEW RATE (V/µs) 350 300 250 200 150 100 -50 -25 0 25 50 75 TEMPERATURE (oC) 100 125 - SLEW RATE + SLEW RATE NORMALIZED GAIN (dB) 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1.0 -1.2 5 10 15 20 FREQUENCY (MHz) 25 30 AV = +10, RF = 383Ω AV = +1, RF = 1kΩ AV= +5, RF = 1kΩ AV= +2, RF = 681Ω VOUT = 0.2VP-P CL = 10pF FIGURE 25. SLEW RATE vs TEMPERATURE FIGURE 26. NON-INVERTING GAIN FLATNESS vs FREQUENCY 12 HA5022 Typical Performance Curves 0.8 0.6 NORMALIZED GAIN (dB) 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1.0 -1.2 5 10 15 20 25 30 FREQUENCY (MHz) AV = -10 AV = - 2 0 0.01 0.1 1 FREQUENCY (kHz) 10 0 100 AV = - 5 AV = - 1 VOUT = 0.2VP-P CL = 10pF RF = 750Ω VSUPPLY = ±5V, AV = +1, RF = 1kΩ , RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued) 100 AV = +10, RF = 383Ω VOLTAGE NOISE (nV/√Hz) 1000 60 +INPUT NOISE CURRENT 40 INPUT NOISE VOLTAGE 20 600 400 200 FIGURE 27. INVERTING GAIN FLATNESS vs FREQUENCY FIGURE 28. INPUT NOISE CHARACTERISTICS 1.5 2 1.0 VIO (mV) BIAS CURRENT (µA) 0 0.5 -2 0.0 -60 -40 -20 0 20 40 60 80 100 120 140 -4 -60 -40 -20 0 20 40 60 80 100 120 140 TEMPERATURE (oC) TEMPERATURE (oC) FIGURE 29. INPUT OFFSET VOLTAGE vs TEMPERATURE FIGURE 30. +INPUT BIAS CURRENT vs TEMPERATURE 22 4000 TRANSIMPEDANCE (kΩ) BIAS CURRENT (µA) 20 3000 18 2000 16 -60 -40 -20 0 20 40 60 80 100 120 140 1000 -60 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (oC) TEMPERATURE (oC) FIGURE 31. -INPUT BIAS CURRENT vs TEMPERATURE FIGURE 32. TRANSIMPEDANCE vs TEMPERATURE 13 CURRENT NOISE (pA/√Hz) 140 80 -INPUT NOISE CURRENT 800 HA5022 Typical Performance Curves VSUPPLY = ±5V, AV = +1, RF = 1kΩ , RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued) 25 125oC REJECTION RATIO (dB) 20 55oC 74 72 70 68 -PSRR 66 64 62 60 58 -100 CMRR +PSRR ICC (mA) 15 10 25oC 5 3 4 5 6 7 8 9 10 11 12 13 14 15 -50 0 50 100 150 200 250 SUPPLY VOLTAGE (±V) TEMPERATURE (oC) FIGURE 33. SUPPLY CURRENT vs SUPPLY VOLTAGE FIGURE 34. REJECTION RATIO vs TEMPERATURE 40 4.0 SUPPLY CURRENT (mA) 20 OUTPUT SWING (V) 3 4 5 6 7 8 9 10 11 12 13 14 15 30 +5V +10V +15V 3.8 10 0 0 1 2 DISABLE INPUT VOLTAGE (V) 3.6 -60 -40 -20 0 20 40 60 80 100 120 140 TEMPERATURE (oC) FIGURE 35. SUPPLY CURRENT vs DISABLE INPUT VOLTAGE FIGURE 36. OUTPUT SWING vs TEMPERATURE 30 1.2 VS = ±15V 20 VOUT (VP-P) VIO (mV) 10.00 1.1 VS = ±10V 10 1.0 0.9 VS = ±4.5V 0 0.01 0.8 0.10 1.00 -60 -40 -20 0 20 40 60 80 100 120 140 LOAD RESISTANCE (kΩ) TEMPERATURE (oC) FIGURE 37. OUTPUT SWING vs LOAD RESISTANCE FIGURE 38. INPUT OFFSET VOLTAGE CHANGE BETWEEN CHANNELS vs TEMPERATURE 14 HA5022 Typical Performance Curves 1.5 VSUPPLY = ±5V, AV = +1, RF = 1kΩ , RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued) 30 -55oC 25 ∆BIAS CURRENT (µA) 1.0 ICC (mA) 20 25oC 15 0.5 10 125oC 0.0 -60 -40 -20 0 20 40 60 80 100 120 140 TEMPERATURE (oC) 5 3 4 5 6 7 8 9 10 11 12 13 14 15 SUPPLY VOLTAGE (±V) FIGURE 39. INPUT BIAS CURRENT CHANGE BETWEEN CHANNELS vs TEMPERATURE FIGURE 40. DISABLE SUPPLY CURRENT vs SUPPLY VOLTAGE -30 A V = +1 VOUT = 2VP-P -40 ENABLE TIME (ns) SEPARATION (dB) 32 30 28 26 24 22 20 18 16 14 DISABLE -0.5 0 0.5 1.0 1.5 2.0 DISABLE ENABLE ENABLE 20 18 16 14 12 10 8 6 4 2 0 2.5 DISABLE TIME (µs) -50 -60 -70 -80 0.1 1 FREQUENCY (MHz) 10 30 12 -2.5 -2.0 -1.5 -1.0 OUTPUT VOLTAGE (V) FIGURE 41. CHANNEL SEPARATION vs FREQUENCY FIGURE 42. ENABLE/DISABLE TIME vs OUTPUT VOLTAGE 15 HA5022 Typical Performance Curves VSUPPLY = ±5V, AV = +1, RF = 1kΩ , RL = 400Ω, TA = 25oC, Unless Otherwise Specified (Continued) 0 -10 FEEDTHROUGH (dB) -20 -30 -40 -50 -60 -70 -80 0.1 DISABLE = 0V VIN = 5VP-P RF = 750Ω TRANSIMPEDANCE (MΩ) 10 1 0.1 0.01 0.001 180 135 90 45 0 -45 -90 PHASE ANGLE (DEGREES) RL = 100Ω 1 FREQUENCY (MHz) 10 20 0.001 0.01 0.1 1 FREQUENCY (MHz) 10 -135 100 FIGURE 43. DISABLE FEEDTHROUGH vs FREQUENCY FIGURE 44. TRANSIMPEDANCE vs FREQUENCY TRANSIMPEDANCE (MΩ) 10 1 0.1 PHASE ANGLE (DEGREES) 0.01 0.001 180 135 90 45 0 -45 -90 -135 0.001 0.01 0.1 1 FREQUENCY (MHz) 10 100 RL = 400Ω FIGURE 45. TRANSIMPEDENCE vs FREQUENCY All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 16 HA5022 Die Characteristics DIE DIMENSIONS: 1650µm x 2540µm x 483µm METALLIZATION: Type: Metal 1: AlCu (1%) Thickness: Metal 1: 8kÅ ±0.4kÅ Type: Metal 2: AlCu (1%) Thickness: Metal 2: 16kÅ ±0.8kÅ SUBSTRATE POTENTIAL (POWERED UP): VPASSIVATION: Type: Nitride Thickness: 4kÅ ±0.4kÅ TRANSISTOR COUNT: 124 PROCESS: High Frequency Bipolar Dielectric Isolation Metallization Mask Layout HA5022 -IN1 OUT1 V+ +IN1 DIS1 VNC DIS2 +IN2 -IN2 OUT2 17